Sevo GS PG 8119 - Grill plate SEVERIN - Free user manual and instructions

USER MANUAL Sevo GS PG 8119 SEVERIN

Black SEVO grill with red grating and stainless steel stand (no visible text or symbols)

eBBQ

ART.-NO. PG 8119 SEVO GS

GB Instructions for use

FR Mode d'emploi

Exploded view diagram of a microwave oven with numbered parts for identification

Standgrill

Before using the appliance, read the following instructions carefully and keep this manual for future reference. The appliance must only be used by persons familiar with these instructions.

Familiarisation

1. Wind-guard, 2 parts
2. Grill rack, 2 parts
3. Heating element with junction box
4. Rotary control with display and light-ring
5. Power cord with plug
6. Reflector tray inserts
7. Reflector tray
8. Grill housing
9. Core thermometer, 1 piece

Base stand:

1. Base stand frame
2. Support legs, 4 pieces
3. Storage rack
   Not illustrated:
   4 screws
   4 wing nuts

Important safety instructions

• The appliance should only be connected to an earthed socket installed in accordance with the regulations.
• The appliance is also designed for outdoor use, and must therefore be operated with an additional earth-leakage circuit-breaker with a rated tripping current not exceeding 30mA.
• Make sure that the supply voltage corresponds with the voltage marked on the rating label.
• The power cord should be regularly examined for any signs of damage. In the event of such damage being found, the appliance must no longer be used.
• In order to avoid hazards, and to comply with safety requirements,

repairs to this electrical appliance or its power cord must be carried out by our customer service. If repairs are needed, please contact our customer service department by phone or email (see appendix).

Caution: This symbol indicates that the wind-guard, and heating element may very hot during operation - a danger of burns.

• Before cleaning the grill, ensure it is disconnected from the power supply and has completely cooled down.
• To avoid the risk of electric shock, the heating element with sensor and power cord and the core thermometer must not be immersed in liquid or even allowed to come into contact with it.
• Clean the grill rack, reflector tray, the tray inserts and wind-guard with hot soapy water, or in a dish-washer. For detailed information on cleaning the appliance, please refer to the section Cleaning and care.
• The appliance is not intended to be operated by means of an external timer or separate remote-control system.
• Warning! Do not, under any circumstances, use charcoal or any other solid or liquid fuel to operate the grill.

• Caution: Do not cover the grill rack with aluminium foil, barbecue dishes or other items, as the resulting build-up of heat could seriously damage the grill.

• A maximum of 2 litres of water may be poured into the reflector tray.

• This appliance is intended for domestic or similar applications, such as

• in staff kitchens in shops, offices and other similar working environments,

• in agricultural working environments,
• by customers in hotels, motels etc. and similar establishments,
• in bed-and breakfast type environments.

- This appliance may be used by children (at least 8 years of age) and by persons with reduced physical, sensory or mental capabilities, or lacking experience and knowledge, provided they have been given supervision or instruction concerning the use of the appliance and fully understand all dangers and safety precautions involved.

• Children must not be permitted to play with the appliance.
• Children must not be permitted to carry out any cleaning or maintenance work on the appliance unless they are supervised and at least 8 years of age.
• The appliance and its power cord must be kept well away from children under 8 at all times.
• Caution: Keep any packaging materials well away from children – these are a potential source of danger, e.g. of suffocation.

• Before the appliance is used, the main body as well as any attachment fitted should be checked thoroughly for any defects. Should the appliance, for instance, have been dropped onto a hard surface, it must no longer be used: even invisible damage may have adverse effects on the operational safety of the appliance.

• During operation, the grill must be placed on a level, heat-resistant surface, impervious to splashes and stains. When grilling food with a high fat or moisture content, splashes are not always avoidable.

• Do not position the grill next to a wall or corner, and ensure that no inflammable materials are stored near it.
• Remember that food with a high fat or moisture content may tend to ignite; therefore always fill the reflector tray with water before use. Do not connect the grill to mains power until the trey has been filled with water. The water helps to cool down the reflector tray, reduces the build-up of smoke, and also facilitates cleaning.

Keep monitoring the water level. Water should be added in good time, while ensuring that it does not come into contact with the heating element. Caution: Disconnect the grill from the mains before adding water.

• Before the grill is used, always check that the heating element is correctly fitted in the housing and reflector tray.

• The grill must be supervised at all times during operation.

• Do not allow the power cord to touch any hot parts of the appliance.

• Route the power cord in such a way that no one can trip over it.

- Always remove the plug from the wall socket

• before filling with water,
• after use,
• in case of any malfunction, and
• during cleaning.

- The use of an extension cord or reel causes a loss of power, possibly combined with a subsequent heat build-up in the cable. It is therefore necessary to unwind the cable completely before use. Make sure that the cord is approved for outdoor use and for the power specified (see rating label).

• Never move the barbecue while it is in operation.
• Remove water after use.

- Caution! Always make sure that the barbecue has cooled down completely before it is moved, cleaned, covered or stored.

• Caution! Whenever the barbecue is not in use, the heating element with the connection box must be removed from the barbecue and stored in a dry space indoors.
• The other parts of the barbecue must not be stored outdoors or in an open area where they could be affected by the weather.
• The grill may only be used with the supplied core thermometer or the SEVERIN item no. ZB 8126.
• No responsibility is accepted if damage results from improper use, or if these instructions are not complied with.
• This product complies with all binding CE labelling directives.

Before using for the first time

• Remove any packaging materials and stickers from the appliance.
• Clean the grill rack, reflector tray, the tray inserts and wind-guard with warm soapy water; wipe thoroughly dry afterwards.
• Assemble the appliance as described in Preparing the unit.
• Let the grill heat up for approximately 10 minutes at maximum power without any food (see 'Boost-zone' grilling). This will remove the smell typically encountered when first switching on a grill. A little smoke may be emitted; for that reason, adequate ventilation should be ensured by opening windows or balcony doors; an extractor hood is also suitable.

Grill assembly

• Assemble the grill as shown in the diagrams:
• Place the reflector tray into the grill housing.
• Note: Fit the tray inserts so that each insert covers four protrusions.
• Fit the heating element with junction box into the reflector tray. The appliance is equipped with a safety switch. The unit can be operated only with the junction box properly installed.
• Fit both grill rack elements so that the studs on the rack fit into the corresponding openings in the reflector tray.
• Fit the wind-guard elements first at the rear into the recesses on the grill rack, and then secure them on the grill rack frame.

Assembling the base stand

Assemble the base stand as shown in the figure:

• Insert the four support legs into the frame from below until they engage.
• Insert the storage grate and secure it to the support legs with the four wing nuts.
• Check that the base stand is secure.
• Put on the assembled grill.

The maximum load of the storage grate is 9 kg.

Preparing the unit

• Assemble the unit as described in "Grill assembly" and "Assembling the base stand".
• Fill the reflector tray with water to the Max marking (max 2 litres). Do not pour water on the heating element or its sensor.

Hint!

During grilling, the water in the reflector tray should be replenished in good time. Caution: Always disconnect the appliance from the mains before re-filling.

• Connect the appliance to the mains.
• The light ring lights up blue, the unit is ready for use.

Rotary control

The rotary control is used for function selection or switching off (Sleep mode).

Turn:

Select the Function/Temperature/Timer.

Push - short:

Confirm the selection.

Push - two seconds:

1 x: return to stand-by mode to change a function
2 x: return to sleep mode

Rotary control - light ring

The light ring indicates the current operating mode:

No light:

The unit is in sleep mode.

Blue light:

The unit is in stand-by mode.

Flashing:

The grill rack has not yet reached the selected temperature.

The unit is heating up or cooling down.

Steady:

The selected temperature has been reached.

Orange:

Grilling 80-320 °C

Red:

Boost-zone 330-500 °C

Timer

The timer is used to monitor the grilling time. It can be set from 1 min to 23 h 59 mins. Beep signals indicate that the running time has elapsed; the heating element remains switched on.

• Turn the rotary control until lights up.
• Press the rotary control briefly and turn to select the hours.
• Press the rotary control briefly and adjust the minutes.
• Confirm the time setting by briefly pressing the control. The colon starts flashing; once the time has elapsed, beep signals are heard.
• To return to stand-by mode, press the rotary control for two seconds.
• Alternatively, set the timer to 0:00, and press the control briefly to return to stand-by mode.
• If the heating is switched off after the timer is set, the appliance will change to sleep-mode 5 minutes after the last input, i.e. the timer is switched off.
• If the timer is set with the heating already off, it will continue until the pre-selected time is reached, when the unit changes to sleep-mode.

Grilling 80-320 °C

To grill sausages, poultry, fish etc. For finishing or keeping warm steaks.

The entire grill surface is heated.

• Turn the rotary control until lights up.
• Press the rotary control briefly and turn to select the desired temperature. Press briefly to confirm.
• The ring starts flashing orange and the appliance is heating up.
• Once the selected temperature has been reached, the ring shows steady orange.
• Place the food on the grill surface.

'Boost-zone' grilling 330-500 °C

For searing or light grilling of steaks.

The boost-zone is located to the right; the left side is heated to 320 °C.

• Turn the rotary control until lights up.
• Press the rotary control briefly and turn to select the desired temperature. Press briefly to confirm.
• The ring starts flashing red and the appliance is heating up.
• Once the selected temperature has been reached, the ring shows steady red.
• Place the food on the boost-zone.
• For subsequent cooking, lower the temperature or shift the food to the left on the grill surface.

1 Grilling with the core thermometer

• Scope of supply: 1 piece
Other core thermometers are available under item no. 8126.
- Fit the thermometer plugs into the sockets at the lower left of the junction box. To prevent the appliance from switching off, ensure that the box is not lifted up and stays properly connected.
- Select the desired grill function and temperature.
- Once pre-heating is complete and the ring shows a steady light, put on the food.
- Push the tips of the thermometers into the centre of the food.
- Use the rotary control to set the desired core temperature - ① . Press briefly to confirm.
- The display shows the respective current core temperature.
- Once the pre-set core temperature on one thermometer is reached, three long beep signals are heard.
- Remove the respective thermometer and take off the food.

Note:

The grill plate remains on even after the pre-set core temperature has been reached.

Stand-by mode

• To switch off the heating and return to stand-by mode, press the rotary control for two seconds.
- Alternatively, press the control briefly, set the temperature to 00 and press again briefly to return to stand-by mode.

Sleep mode

• If the heating is switched off, the appliance will change to sleep-mode 5 minutes after the last input.
• To switch off earlier, press the rotary control for two seconds.

After grilling

• Always disconnect the unit from the mains and allow it to cool down after grilling.

Cleaning and care

• Ensure that the grill is thoroughly cleaned after use.
• Before cleaning the grill, ensure it is disconnected from the power supply and has completely cooled down.
• Do not use metallic pads or abrasive cleaning agents.
• Remove the wind-guard and grill rack and clean them in a dish-washer or with warm soapy water. To remove persistent food residues, they can be left soaking for a while.
• Remove the heating element. To avoid the risk of electric shock, do not clean the heating element with water and do not immerse it in water. The junction box may be wiped with a slightly damp lint-free cloth.
  Take off the reflector inserts and tray and clean them in a dish-washer or with warm soapy water. To remove persistent food residues, they can be left soaking for a while.
• The core thermometer tips may be wiped with a moist cloth.
• All other parts can be cleaned with a cloth soaked in soapy water, and should be wiped completely dry afterwards.

Hint!

To help clean the wind-guard, grill rack and reflector tray, baking powder may be used. Mix a paste from water and baking powder, rub the paste onto the affected areas and let it take effect for a while. Clean with a soft brush/sponge and rinse thoroughly afterwards.

Disposal

Devices marked with this symbol must be disposed of separately from your household waste, as they contain valuable materials which can be recycled. Proper disposal protects the

environment and human health. Your local authority or retailer can provide information on the matter.

Guarantee

This product is guaranteed against defects in materials and workmanship for a period of two years from the date of purchase. Under this guarantee the manufacturer undertakes to repair or replace any parts found to be defective, providing the product is returned to one of our authorised service centres. This guarantee is only valid if the appliance has been used in accordance with the instructions, and provided that it has not been modified, repaired or interfered with by any unauthorised person, or damaged through misuse.

This guarantee naturally does not cover wear and tear, nor breakables such as glass and ceramic items, bulbs etc. This guarantee does not affect your statutory rights, nor any legal rights you may have as a consumer under applicable national legislation governing the purchase of goods. If the product fails to operate and needs to be returned, pack it carefully, enclosing your name and address and the reason for return. If within the guarantee period, please also provide the guarantee card and proof of purchase.

Chère cliente, Cher client,

Grillen 'Boost-zone' 330-500 °C

1 Angel Kanchev, 5th floor

1000 Sofia, Bulgaria

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Croatia

Koracell d.o.o.

Donje Svetice 40

26 Oaktree Business Park

Trim Co., Meath

Tel.: [phone]

Fax: [phone]

Web: www.bluestone.ie

Italia

ASSISTENZA POST-VENDITA

NUMERO VERDE 800224155

E-Mail: [e-mail]

Indonesia

PT. Setai Modern Elektronik

Email.: [e-mail]

Web.: www.severin.co.id

Jakarta

Komp. Glodok Plaza Blok F No. 9, Jl. Pinangsia Raya,

Jakarta Barat

021 65911888 / 021 6592889

Medan

JI. Apel No. 88 Kom. Cemara Asri

061 6620186 / 061 6625836

Surabaya

Pergudangan Mutiara Margo Mulyo Indah,

Blok DC No. 2

Telp : [phone], [phone]

Banjarmasin

Dr.Waleed Maraga commercial center, Level 1

Khalda, Amman Zip code: 11953

Tel: [phone]

Fax: [phone]

Mob Jordan: [phone]

Kuwait

Mohammed Abdulrahman Al Bahar

Al Bahar Building P.O. Box 148

Safat 13002 Kuwait

Tel.: [phone]

Latvia

SIA GTCL BALTIC

Piedrujas iela 7

LV - Riga 1073

Tel.: [phone]

Fax: [phone]

Lebanon

Khoury Home

7th Floor, Cité Dora 3 Building, Dora

P.O.Box 70611

Antelias, Lebanon

Tel.: [phone]

Fax:[phone]

E-Mail: [e-mail]

Internet: www.khouryhome.com

Lithuania

UAB Topo Grupe

Savanoriu PR. 206A,

50193 Kaunas, Lithuania

Tel.: [phone]

A.A.K & Partners L.L.C.

P.O Box:-1650, Muttrah

Postal Code - 114

Sultanate of Oman

Tel.: [phone]

Fax.: [phone]

E-Mail: [e-mail]

Peru

SEVERIN PERU / Comercial Rebeca S.R.L

Mezzanine 1, South Center Tower

2206 Venture Street, Madrigal Business Park

Alabang, Muntinlupa City

Tel.: [phone]

E-Mail: [e-mail]

Polska

Severin Polska Sp.z o.o.

6 Tagore Drive, #03-04

Singapore 787623

Tel.: [phone]

Fax: [phone]

Web: www.beste.com.sg

E-Mail: [e-mail]

Slovenia

SEVTIS d.o.o.

Smartinska 130

1000 Ljubljana

Tel.: [phone]

Fax: [phone]

Slowak Republic

BVZ Commerce s.r.o.

Parkerova 618

CZ 25067 Klecany

Tel.: [phone]

Fax: [phone]

South Africa

AL&CD Ashley (PTY) Ltd.

3rd Floor, Grove Exchange

Grove Avenue

Claremont

South Africa

7708

Tel: [phone]

Fax: [phone]

Web: http://www.alcdashley.co.za

Mail: [e-mail]

Svenska

EI & Digital Service AB

Folkungagatan 144

11630 Stockholm

Tel.: [phone]

www.eldigital.se

E-Mail: [e-mail]

Switzerland

SPC Electronics AG

Mövenstrasse 12

CH – 9015 St. Gallen

Tel.: [phone]

E-Mail: [e-mail]

www.spc.ch

Thailand

Verasu Ltd. part.

83/7 Wireless Rd., Lumpini,

Patumwan, Bangkok 10330

Tel.: [phone]

E-Mail: [e-mail]

Tunisie

GEI

54, rue du Mercure

Zone Industrielle 2013-BEN AROUS

TUNISIE

Ukrayina

Service for Modern Electronics LLC

Sim'i Khokhlovykh Str.8

4119 Kiev

Tel.: [phone]

E-Mail: [e-mail]

United Kingdom

Homespares Centres Limited

Firwood Industrial Estate

Thicketford Road

Bolton, BL2 3TR

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Web: www.homespares.co.uk

Vietnam

BRAND PARTNER

CTY TNHH DOI TAC NHAN HIEU

2/7 NGUYEN THANH Y

DA KAO WARD, DISTRICT 1

HO CHI MINH CITY, VIETNAM

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Stand: 01.2021