MZE-25 - Iron MPM - Free user manual and instructions

USER MANUAL MZE-25 MPM

EN We wish you satisfaction from using the product and invite you to check a wide range of other MPM/ appliances

Blue and black steam iron with a handle, no visible text or symbols

C2 NAVOD K OBSUZE

Labeled diagram of a blue electric iron with numbered parts for identification

BEZPEČNOSTNÍ POKYNY PŘI POUŽÍVÁNÍ

-Read the instructions carefully before use.
-The iron should be connected to an earthed mains socket.
-Take special care when children are near the device. The iron's soleplate must not be touched during ironing.
- Do not immerse the device, cable or plug in water or other liquids!
-Do not leave the iron unattended if connected to the mains.
- Do not hang the cable on sharp edges or allow it to come into contact with hot surfaces.

- Regularly check the power cord and the connecting hose for any damage.

- Never use a damaged device, including one with a damaged cord or plug, in which case have it repaired at an authorised service centre.

-Always unplug the device when not in use.

-Before cleaning, first unplug the device from the mains socket and wait until it has cooled down completely.

- Disconnect the device from the mains before filling in or emptying the tank.

-Never touch the iron's soleplate when it is on!

- Fill the tank with water only. It is recommended to use distilled water to avoid limescale buildup on the iron's internal parts.

- Do not add any chemical agents to the water in the tank - they may damage the device.

-To avoid burns, do not touch the device's hot metal parts, hot water or steam.

- Do not use the device for purposes other than those for which it was intended.

-The device is intended for domestic use only.

-Do not use the device outdoors.

-Do not open the water tank's cover when using the device.

-The iron must be used and put away on a flat surface.

- Do not use the iron if it fell down, shows signs of damage or leaks.

-This equipment may be used by children of at least 8 years of age and by persons of diminished physical, mental capacity and lack of experience and knowledge of the equipment if supervision or instruction is provided regarding the safe use of the equipment so

that the hazards involved are understood. Unsupervised children should not perform cleaning and maintenance on the equipment.

-Keep the device and its cord out of reach of children under 8 years of age.

- Children should be supervised to ensure that they do not play with the equipment/device.

-Pour out the water remaining in the tank after the ironing is finished.

- Never iron clothes or fabric that are worn or placed on people or pets.

- Never direct the steam at people or pets.

• Do not pull the plug out of the power socket by pulling the cord.
• Do not connect the plug to the power socket with wet hands.
• Do not wind the power cable around the iron until it cools down.
• Do not place the device near electric or gas cookers, burners, ovens, etc.
• The equipment is not designed to operate using external timers or a separate remote control.
• When putting the iron away on the stand, make sure the surface on which the stand is placed is stable.
• Before switching the device on, make sure the mains parameters match the values on the device's identification plate.
  -For the safety of children, please do not leave freely accessible parts of the packaging (plastic bags, cardboard boxes, polystyrene, etc.).
• WARNING! Do not allow children to play with the film. Danger of suffocation!

CAUTION! HOT SURFACE!

DEVICE DESCRIPTION

1. Steam control slider and the function of self-cleaning the iron from deposits
2. Maximum water filling indicator
3. Water sprayer button
4. High steam impact button
5. Temperature control knob:

6. 1.9 m rotating mains cable

7. Operational status and mains connection indicator light

8. Water tank with a capacity of 220 ml
9. Non-stick coated soleplate
10. Sprayer hole
11. Water filler cover
12. Hand
13. Rear housing/base

BEFORE FIRST USE

1. Remove all stickers, covers and protective film from the iron's soleplate.
2. Wash and rinse the measure.
   CAUTION! A smoke may come out of the iron during the first use. This phenomenon stops after a short while.

PREPARATION FOR USE

FILLING THE WATER TANK

1. Make sure the device is not connected to the mains.
2. Set the steam control slider in (1) the "NO STEAM" position ✿.
3. Open the water filler cover (11).
4. Fill the water tank (8) to the maximum level using the measure. Check the maximum water level by placing the iron in the vertical position.

CAUTION! Do not fill the tank over the MAX level. In order to get the best results, always use fresh demineralized or distilled water. Do not use chemically descaled water or any other liquids.

1. Close the water filler cover (11).

USING THE DEVICE

TEMPERATURE SETTING

1. Connect the power cord plug (6) to a grounded power socket. The indicator lamp (7) will light up green.
2. Place the iron in an upright position and set the required ironing temperature by turning the temperature control knob (5) to the appropriate position. The indicator lamp (7) will change the colour to red to indicate the heating.

MARKING ON THE IRON THERMOSTAT ADJUSTMENT FABRIC TYPE

• low temperature synthetic materials
• average temperature silk, wool
•• /max	high temperature	cotton, linen

CAUTION! Check the required ironing temperature marked on the tag. If you do not know the fabric type of the ironed product, the correct ironing temperature should be determined by iron

ing the part of the product that will be invisible when worn or used. We start from the lowest temperature gradually increasing it . Silk, wool and man-made fabrics - to prevent the formation of shiny stains, iron fabrics on the left side covering them with another thin fabric. Do not use the sprayer function to prevent the formation of stains when ironing. Iron velvet and similar materials in one direction, do not hold them in one place. Iron synthetic fabrics and silk on the left side without using steam.

CAUTION! Always start ironing with the products requiring the lowest ironing temperature.

1. When the iron reaches the desired temperature the indicator light (7) goes out, wait a moment and you can start ironing.

STEAM IRONING

1. Check whether there is an appropriate amount of water in the tank (8).
2. Set the recommended temperature (see: "TEMPERATURE SETTING").
3. Select the appropriate steam setting 🎨 using the control slider (1).

CAUTION! Steam ironing is possible only at higher ironing temperature (temperature settings from ●● to ●●●).

CAUTION! As the iron reaches the selected temperature, it will start to produce steam. The device produces steam at a very high temperature!

IRONING WITHOUT STEAM

1. Set the steam controller in (1) the "NO STEAM" position
2. Set the recommended ironing temperature (see: "TEMPERATURE SETTING").

SPRAYER FUNCTION

This function may be used in order to remove the stubborn creases.

1. Check whether there is a sufficient amount of water in the tank (8).
2. In order to moisten the fabric that is to be ironed, press the sprayer button (3) several times.

HIGH STEAM IMPACT FUNCTION

This function (4) may be used in the vertical and horizontal position. It is useful for removing creases on the hanging clothes, curtains, etc.

CAUTION! The iron shoots a lot of hot steam! Risk of scalding! Do not direct the vapor stream at people or animals!

ANTI DRIP SYSTEM

The iron is equipped with the anti-drip system: the iron will automatically stop producing steam when the temperature is too low.

AFTER FINISHING IRONING

1. Set the temperature knob to the minimum position.
2. Unplug the power cord (6) from the electrical socket.
3. After ironing with the use of steam, empty the water tank (8).
4. Put the iron in a safe place in an upright position and wait for it to cool down.

CLEANING AND MAINTENANCE

CAUTION! Never submerge the iron in water or rinse it under running water.

1. Wipe off limescale and other deposits from the iron's soleplate (9) with a damp cloth and a (liquid) non-abrasive cleaner.

CAUTION! To keep the surface of the soleplate unscratched, the iron should not be placed near any metal objects. Do not use scourers, vinegar or other chemicals to clean the soleplate.

1. Wipe the upper part of the iron with a damp cloth.
2. Regularly rinse the tank with water (8) and empty it after rinsing.

SELF CLEAN FUNCTION - SELF-CLEANING

Use this function once in two weeks. Especially if you use tap water instead of distilled water. If the water in the area is very hard (i.e. limescale falls off the iron's soleplate during ironing), the function should be used more frequently.

1. Make sure that the device is not connected to power sources.
2. Set the steam slider in (1) the "NO STEAM" position 🌿.
3. Fill the tank to the MAX level.
4. Insert the plug to the earthed electric socket.
5. Select the maximum ironing temperature.
6. When the indicator lamp goes off, disconnect the iron from power sources.
7. Holding the iron over the sink, move the slider towards SELF CLEAN (2), then gently shake the iron. Steam and hot water will start to escape from the iron's soleplate. Impurities and limescale deposits will be flushed out.
8. After emptying the tank of water, release the SELF CLEAN slider (2). This activity must be repeated, if there are lots of impurities in the iron.

ANTI CALC FUNCTION - ACTIVE ANTI-SCALE SYSTEM

The anti-scale cartridge prevents the steam outlet holes from being clogged by limescale. It is permanently active and needs no replacement.

Do not use limescale removal agents as this may destroy the anti-scale cartridge.

STORAGE

1. Set the steam controller in the "NO STEAM" position ⚙ and remove the plug from the mains socket.
2. Empty the water tank (8).
3. Wait until the iron cools off. Wind the mains cable around the iron.
4. Always store the empty iron in an upright position on a stable surface.

TECHNICAL DATA:

Technical specifications are given on the product nameplate. Length of mains cable: 1.9 m

CAUTION! MPM agd S.A. reserves the right to technical changes.

Proper disposal of the product (waste electrical and electronic equipment)

Marking on the product indicates that after the service-life of the product expires, it should not be disposed with other type of municipal waste. Used equipment may have a negative impact on the environment and health of people due to potentially containing hazardous substances, mixtures and components.

Mixing electric waste with other types of waste or disassembling those in an unprofessional manner may cause a release of substances that are hazardous to the environment and health. Used equipment should

be handed-over to a point for collection of electric waste. In order to obtain detailed information regarding the electric waste collection points, the user should contact the municipal point of electric waste collection or used equipment processing department.

BESCHRIJVING VAN HET APPARAAT

ANTI CALC FUNCTIE - ACTIEF ANTIKALKSYSTEEM

FUNCTIA ANTI CALC - SISTEM ACTIV ANTICALC