FX-4MS142 - Lawn mower Fuxtec - Free user manual and instructions

USER MANUAL FX-4MS142 Fuxtec

Petrol brush cutter/grass trimmer FX-4MS142

Your new device has been developed and designed to meet FUXTEC's high standards, such as easy operation and user safety. Properly treated, this device will serve you well for years to come.

WARNING: To reduce the risk of injury, the user must read and understand this manual

before operating the device.

FUXTEC GMBH KAPPSTRAßE 69, 71083 HERRENBERG, GERMANYManual_FX-4MS142_Int24_rev2 We are constantly striving to improve our products. Therefore technical data and illustrations can change!

Type FX-4MS142 Engine type 142F, air-cooled; 4-stroke Cubic capacity 42.5cm

Maximum output power (kW) (in accordance with ISO 8893)

The maximum speed of the engine

Idle speed of the machine

Maximum diameter of the thread Ф440mm (Φ2.5mm) Rotation direction of the cutting device Counterclockwise (see the mark on the plate) Number of the handle 2 pieces Dry weight (kg)

Fuel tank capacity (ml)

Oil tank capacity (ml) 100ml Oil FUXTEC 4-stroke oil (SAE30) Fuel consumption (kg/h) (in accordance with ISO 8893)

Specific fuel consumption (g/kWh) (in accordance with ISO 8893)

Weight (net/gross) in (kg)

ALWAYS WEAR EYE PROTECTION, EAR PROTECTION, AND HEAD PROTECTION

WEAR FOOT PROTECTION.

ALWAYS KEEP 15 METERS AWAY FROM OTHER

WARNING OF FLYING OBJECTS

FUMES FROM THIS PRODUCT CONTAIN

Before use, fill in 70ml of engine oil 4 strokes and check every 10 hours.

Please follow the instructions for refueling

Do not allow others to use this machine unless they are fully responsible and have read and understood the machine manual and are trained in its operation.Manual_FX-4MS142_Int24_rev2

Extensive use of a tool exposes the user to shocks that can lead to white finger disease (Raynaud's syndrome) or carpal tunnel syndrome. This condition reduces the hand's ability to feel and regulate temperatures, causes numbness and sensations of heat, and can lead to nerve and circulatory damage and tissue death. Not all factors leading to white finger disease are known. Still, cold weather, smoking, and conditions affecting blood vessels and circulation, as well as extensive or prolonged exposure to shocks, are mentioned as factors in the development of white finger disease. To reduce the risk of white finger disease and carpal tunnel syndrome, please note the following Wear gloves and keep your hands warm. Take regular breaks. All the above precautions cannot eliminate the risk of white finger disease or carpal tunnel syndrome. Long-term and regular users are, therefore, advised to monitor the condition of their hands and fingers closely. Consult a doctor immediately if any of the above symptoms occur. The operating noise of the tool may damage your hearing. Wear a sound-proofing (Oropax or ear muffs) to protect it. Long-term and regular users are recommended to check your hearing regularly. Be especially vigilant and careful when wearing hearing protection as it limits your ability to hear warnings (cries, alarms, etc.). ⚫ WARNING: Some noise exposure from this device cannot be avoided. Do not work in noisy environments during approved and designated times. If necessary, observe rest periods and limit the working time to the absolute minimum. For your protection and protection of persons in the vicinity, wear suitable hearing protection.

18. General Safety Instructions

This machine may only be used for mowing or trimming grass, weeds, and undergrowth. Never use it for other purposes, as this may cause injuries! Correct safety instructions must be observed. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general safety instructions. ⚫ Always wear safety glasses for eye protection. Long hair must be tied back. Do not wear loose clothing or jewelry that can get caught in moving parts of the machine. Safe, strong, non-slip safety shoes must always be worn. It is recommended that legs and feet are covered to protect against fly debris during operation.Manual_FX-4MS142_Int24_rev2

⚫ Check the entire machine for loose parts over (nut, bolt, screw, etc.). Maintain or replace them if necessary, before you use the device. Do not use accessories with this drive head other than those recommended by our company. Otherwise, severe injuries to the user or bystanders and damage to the machine may result. ⚫ Keep the handles free of oil and fuel. ⚫ Always use the correct handles and shoulder strap when cutting. ⚫ Do not smoke when mixing the fuel or filling the tank. ⚫ Do not mix fuel in a closed room or near open fires. Ensure sufficient ventilation/air circulation. ⚫ Mix and store the fuel mixture in a marked container approved for such consumption according to local regulations. ⚫ Never remove the fuel tank cap while the machine is running. ⚫ Do not operate the machine in a closed room or building. Exhaust gases contain dangerous carbon monoxide. ⚫ Do not attempt to adjust the machine while running or carrying the device. Always adjust the machine on a flat, free surface. ⚫ Do not use the machine if it is damaged. Never remove the protection of the device. Otherwise, severe injuries of the operator or spectators, as well as damage to the device, can result. ⚫ Check the area to be cut and remove any debris that may be entangled in the nylon cutting head or cutting blade. Also, remove any objects that the machine may throw around while cutting. ⚫ Never leave the machine unattended. ⚫ Do not reach far forward. Maintain a firm stand and balance at all times. Do not let the machine run while standing on a rope ladder or any other unstable standing position. ⚫ Children must not have access to the machine. Spectators should be kept at a safe distance from the work area, at least 15 METERS. ⚫ Keep hands and feet free of the nylon cutting head or metal blade during the operation. ⚫ Do not use the machine if you are tired, sick, or under the influence of medication, drugs, or alcohol. ⚫ Use an undamaged nylon cutting head. If you hit a stone or any other obstacle, stop the machine and check the nylon cutting head. Never use a defective or unbalanced nylon cutting head.Manual_FX-4MS142_Int24_rev2

⚫ Before starting, after failure or impact, be sure to check the device and make sure it is in good condition. ⚫ Attention! Local regulations may limit the use of the machine. ⚫ Always keep the device with the cutting tool in good condition. ⚫ Note, improper maintenance, use of non-compliant spare parts, or removal or modification of safety devices can cause damage to the device, and severe injury to the person working with it. ⚫ Secure the device properly during transportation to prevent loss of fuel, damage to the device, and injury. ⚫ For machines with a clutch, regularly check that the cutting attachment stops rotating when the engine is idling. ⚫ Before each use, check the machine for loose fasteners, fuel leaks, damaged parts, etc. Replace damaged parts before use. ⚫ It is necessary to take sufficient breaks and change the working position regularly.

19. Instructions for accessories

⚫ Do not store the machine in an enclosed area where fuel vapors can reach an open fire from water heaters, stoves, etc. Store the device in a well-ventilated area only. ⚫ Make sure that your product is only equipped with original accessories. These parts are available from your dealer. The use of any other accessories or attachments may cause injury to the user and damage to the machine. ⚫ Clean the machine thoroughly, mostly the fuel tank and air filter. All fuel must be removed after using the device. ⚫ IMPORTANT: When filling fuel, make sure that the machine is off and cooled down. Never refuel when the device is running or hot. If gasoline is spilled, wipe it up before starting the machine. ⚫ Keep at least 15m distance to other persons during the work. ⚫ If you, as a spectator, approach a user of the machine, carefully attract his attention and confirm that the user stops the machine. Please do not startle or distract the user. Otherwise, you could cause an unsafe situation. ⚫ Never touch the nylon cutting head or metal blade when the machine is running. If it is necessary to replace the guard or cutting tool, be sure that the machine and cutting tools have stopped. ⚫ The machine must be OFF before changing the machine's working range. ⚫ Please make sure that the nylon cutting head does not hit against stones or other hard objects. ⚫ Please always make sure that screws have not become loose or that the machine does not overheat.Manual_FX-4MS142_Int24_rev2

⚫ If necessary, have the machine serviced by an authorized dealer. If the device is defective, do not let it continue to run. ⚫ When starting or operating the machine, never touch hot parts like the exhaust, the ignition cables, or the spark plug. ⚫ After the machine has stopped, the exhaust is still hot. Never place the device near inflammable materials (dry grass, inflammable gases, or inflammable liquids, etc.). ⚫ Take special care that the ground can be slippery when operating the machine in the rain or immediately after rain. ⚫ If you slip or fall to the ground, release the throttle immediately. ⚫ Be careful not to drop the machine or hit it against obstacles. ⚫ Before adjusting or repairing the machine, make sure that the device is stopped, and the spark plug connector is removed. ⚫ If the machine is to be stored for an extended period, drain fuel from the fuel tank and carburetor, clean the parts, place the device in a safe place and ensure that the machine has cooled down completely. ⚫ Carry out constant checks to ensure safe and efficient operation. For a complete check of your machine, please contact a specialist workshop. ⚫ Keep the machine away from fire or sparks. ⚫ Be careful when using it. There is a danger of kick-back and recoil. ⚫ Use extreme caution when using this machine with the cutting blade. A cutting blade kick-back is a reaction that can occur when the rotating cutting blade hits an object that cannot be cut. This contact causes the cutting knives to stop for a moment and then suddenly push away from the hit object with accelerated force. This kick-back reaction can be severe enough that the operator loses control of the machine. A cutter blade kick-back can occur without warning if the cutter blade encounters an obstacle, becomes blocked, or jams. This is more likely in areas where it is difficult to see the material being cut. For easy and safe cutting, approach the weeds to be mowed from your right to your left side. If an object or stick of wood is hit unexpectedly, this can reduce a cutter blade kick-back.

CUTTING WITH A CUTTING BLADE

A metal sheet with 3 teeth is equipped with the machine. The metal blade is used for cutting bushes and weeds up to 3/4" in diameter. The use of the saw blade with this machine is prohibited.

WARNING DANGER Do not cut with blunt, cracked or damaged metal sheets. Before working, check the surface for obstacles such as stones, metal bars or other objects. If they cannot be removed, mark this position to avoid collision with the sheet. Lines can become entangled on the blade head and flap or be whirled into the air.Manual_FX-4MS142_Int24_rev2

WARNING DANGER Additionally, wear head, eye, face, and hearing protection and shoes against smooth surfaces. Do not wear bars, jewelry, or loose, dangling clothes that could get caught in the machine. Do not wear footwear with unprotected toes and do not work barefoot or without leg protection. In certain situations, you must wear head protection.

WARNING DANGER Do not use the motor scythe to cut out trees. WARNING DANGER Always use the shoulder strap. Adjust and fix the belt and belt clamping plate on the machine so that the machine hangs a few cm above the floor. The cut-out head and the protective shield should be aligned horizontally in all directions. Pre-tension the machines on the right side of your body.Manual_FX-4MS142_Int24_rev2

The shoulder strap is equipped with a quick-release device (see picture). You can quickly remove the shoulder strap by pulling the quick release. Read the manual carefully. Be thoroughly familiar with the controls and correct use of the machine. Learn how to stop the machine and how to turn off the device. Understand how to stop and shut down the device. Understand how to release a clamped attachment quickly. Do not allow anyone to use the machine without correct instructions. Be sure that the user wears a foot, leg, eye, face, and hearing protection. Keep the area clear of bystanders, children, and pets. Never allow children to operate or play with the machine. Never allow anyone to enter the HAZARDOUS ZONE while working with you. The DANGER ZONE is an area with a radius of 15 meters (approximately 16 steps) or 50 feet. Insist that persons in the DANGER ZONE wear eye protection from thrown objects beyond the danger zone. If the machine is to be used where there are unprotected people, operate at a low, reduced speed to reduce the risk of an object thrown.

*8 GAS LEVER LOCK prevents accidental acceleration of the engine. The throttle stick can only be pressed when the throttle stick lock is pressed.Manual_FX-4MS142_Int24_rev2

21. Mounting the motor scythe

Attaching the handle The handle must be mounted before use. For correct installation, follow the illustrations below. Mounting the handle tube for use Place cup B on the shaft tube, up and down, screw both cups and the shaft tube together. Put the handle into the provided clamping bush, which is already attached to the shaft tube. Now place the other shell on top and screw both half-shells and the grip tube together. Please pay attention to the illustration "Components" to ensure that the handle is in the correct position!

Mounting the drive axle 1). Place the drive axle against the main shaft so that the hole of the axle is aligned with the locking bolt of the connecting piece.

2). Actuate the locking pin and insert the drive axle into the main shaft. Release the locking pin and ensure that the locking pin engages in the hole.

3). Turn the wing screw clockwise to secure the connection.Manual_FX-4MS142_Int24_rev2 Installing the protective shield Install the blade guard on the driveshaft tube against the gear housing. Tighten the holder of the guard so that the blade guard does not move or slide down during operation.

Mounting the lawn trimmer Step 1: Insert the key (1) into the hole in the gear head so that the gear shaft is locked. Unscrew and remove the nut. Since it is a safety nut, please make sure that there is a left-hand thread here Step 2: mount the distance disk (2) and install the thread spool on the gear shaft. And then tighten it by hand. Warning! Make sure that all components are correctly assembled and installed and that all screws are tightened.

Installation of the protective shield Install the protective shield on the driveshaft tube against the gear housing. Tighten the holder of the guard so that the blade guard does not move or slide down during operation.

Mounting the metal blade steps:

1. Place the key (1) in the hole at the gear head.

2. Remove the nut, the cover (4), and the

upper distance disk (3) from the gear shaft

3. Place the metal sheet on the lower

distance disk (2). Make sure that the marked side of the cutting blade is in contact with the disc (2).

4. Slide the upper distance disk (3) over the

gear shaft on the metal sheet. Make sure the upper side of the cutting blade is in contact with the distance disk (3).

5. Put on the cover (4) and screw

the union nut tight with locked gear head (see point 1)

1Manual_FX-4MS142_Int24_rev2 Check the oil level. 1 Place the engine horizontally on the floor. 2 Unscrew the dipstick and check the oil level, which should be up to the oil filler neck 3 If the oil level is too low, add the recommended oil up to the oil filler neck. 4 Close the oil cap.

WARNING The capacity of the oil tank is 75ml. Due to the low capacity, it is necessary to fill the oil slowly to avoid overflow and spillage. Check the oil level every 10 working hours and top up if necessary WARNING We recommend the Oregon 4-stroke oil or other brand oils SAE 10W-30 in average ambient temperature. WARNING The use of 2 stroke oil is not allowed and reduces the life of the engine. The recommended operating temperature is between -5℃ and +40℃ Recommended fuel It is recommended to use unleaded gasoline with an octane number of 90 # or higher to reduce carbon deposition in the combustion chamber. Do not use old or dirty gasoline. Do not use a fuel mixture of engine oil and gasoline. Keep the fuel tank dust-free and avoid water getting into the tank. Sometimes misfiring will occur due to usual overload. If the backfires are heard under the average load, we recommend changing the gasoline. If the misfire is still present afterward, please consult an authorized workshop. WARNING

max. filling level engine oil

● Gasoline is highly flammable, and sparks can cause an explosion. ● Refuel only in well-ventilated rooms and let the engine cool down before filling. Smoking and open fire, as well as any sparks, must be avoided during refueling. ● Do not overfill the tank (the level should not be higher than the tank nozzle). After refueling, check that the tank cap is closed correctly. ● Avoid spilling any gasoline. ● Keep the machine away from children Tank capacity: S35 (139F/P-B) 0.6L Gasoline with an ethanol content The engine can be operated with E10 gasoline. However, do not use gasoline with the higher ethanol content of 10%.

22. Cold start of the machine

1. Place the device on a firm and flat surface.

Slide the engine stop switch down.

2. Move the choke lever upwards to "COLD START."

3. Press the carburetor pump about 8-10 times (until gasoline flows in the line)

4. Pull out the starter rope with a short-stroke until

resistance is felt (about 100mm). A continuous, mainly fast train will provide a strong spark, and the engine will respond after 2-3 trains.

5. Important: After the engine has responded, return the

choke lever to the "WARM START" position and immediately pull the starter again until the engine starts. Also, see the video "Device start" on our homepage.

6. Let the engine warm-up for about 10 minutes at idle

NOTE: If the machine does not start after repeated attempts, refer to troubleshooting chapters.

NOTE: Always pull the starter cord straight out. Pulling the starter at an angle will cause the rope to rub against the eyelet. Pulling the starter at an angle can cause the starter cord to fray or break. Always hold the starter handle firmly when the rope pulls back. Never let the rope be thrown back from the pulled-out position. This could damage the starter device.

23. Warm start of the machine

1. Place the device on a firm and flat surface.

2. Move the engine stop switch down

3. Slide the choke to the "WARM START" position

4. Pull out the starter rope with a short-stroke until resistance is felt

(about 100mm). A continuous high-speed train will provide a strong spark and start the engine If the machine does not start, please proceed again according to "Cold start of the machine STOP MACHINE Unlock the throttle lever. Let the machine return to idle. Push the engine stop switch until the machine stops.

ADDITIONAL SAFETY INSTRUCTIONS

Before running your machine, repeat GENERAL SAFETY INSTRUCTIONS in this manual. CAUTION IF YOU are NOT familiar with the trimming techniques, practice with the MACHINE in the "OFF" position. ALWAYS TRIM OR CUT AT HIGH ENGINE SPEEDS. Do not run the machine slowly at the beginning or when trimming. ALWAYS MAKE DISTANCE IN WORKING AREAS from cans, bottles, rocks, etc. Striking objects can cause serious injury to users or bystanders and can also damage the machine. If an object is accidentally struck, immediately stop the MACHINE and check the device. Never run the machine with damaged or defective parts. DO NOT use the machine for any purpose other than trimming grass. NEVER lift nylon cutting head above knee height when operating. Do not run the machine on a slope if there is a chance of slipping or losing stability.

RELEASE OF THE NYLON CUTTING HEAD

To release fresh thread, leave the machine at full power and "push" on Run nylon cutting head against the lawn. The thread releases automatically. The blade in the protective shield cuts off excess thread.Manual_FX-4MS142_Int24_rev2

CAUTION: Remove grass deposits regularly to prevent overheating of the drive axle. Grass build-up occurs when weed fibers become entangled around the shaft under the protective shield. This condition prevents the shaft from cooling correctly. Remove grass deposits with a screwdriver or similar tool only when the machine is switched off.

When properly equipped with a protective shield and nylon cutting head, your machine will trim unsightly weeds and tall grass with extended reach and areas along fences, walls, land, and around trees. NOTE: Pay special attention when trimming on brick or stone walls, etc., which will cause rapid weed wear.

TRIM MORE ACCURATELY

Swing the trimmer from side to side with a nylon cutting head. Do not tilt the nylon cutting head while working. For correct cutting height, trim in a test area beforehand. For right cutting height, trim in advance in a test area. Keep nylon cutting head at the same level for the uniform depth of the cut.

TRIMMING AROUND TREES

Trim around logs with a slow approach, so the thread does not contact the log. Walk around the tree from left to right. Approach grass or weeds with the tip of the thread and tilt the nylon cutter head slightly. Replace nylon thread

1. Switch off the engine.

2. Place the trimmer on the floor so that the cutting tool is facing upwards with the bobbin.

3. Open the cutting device and the spool by turning the locking knob on the shock absorber.Manual_FX-4MS142_Int24_rev2

4. Cut the new thread to 6 or 5 meters and wind it tightly clockwise around the bobbin.

5. Remove the superfluous thread.

6. After the bobbin is wrapped, fix the thread ends, as shown in the picture.

7. put the cord ends through the holes in the outer part of the bobbin.

8. Press the inner and the outer bobbin together and turn them against each other until they

25. Maintenance and care

Regular checks and adjustments must be made to ensure that the gasoline engine maintains its excellent performance. Periodic maintenance also provides a long service life. See the following table for the regular maintenance cycle.

connecting elements such as screws and nuts Check (tighten if necessary)

Idle speed Check and adjust

Valve clearance Check and adjust

combustion chamber Clean up

WARNING A. Increase maintenance intervals if working in dusty environments. B. All maintenance work - except for the work listed in the operating instructions - must be carried out by qualified maintenance personnel C. For commercial use, maintenance cycles must be adjusted as required. Oil change It is also recommended to replace the oil if it runs hot and loses its lubricating properties. 1 After filling, check that the oil cover is well closed. 2 When changing the oil, unscrew the oil cover and tilt the motor towards the oil filler neck to collect the oil in a suitable container for used oil. 3 Fill in sufficient new 4 cycle oil. 4 Screw the oil cover back in. In case of spillage, please wipe off the overflowing oil and do not forget to wash your hands well with soap. WARNINGManual_FX-4MS142_Int24_rev2

Please contact your local community for the disposal of the used oil. Please do not dispose of used oil in the sewage system or the open environment. Maintenance Air Filter The function of the air filter is to clean impurities like dust from the air and to prevent these dust particles from entering the combustion chamber and the carburetor. To avoid any damage to the carburetor, it is necessary to carry out regular maintenance of the air filter. The maintenance intervals must be increased when working in a dusty environment. WARNING Please do not use alcohol or highly flammable agents to clean the air filter, as this could lead to a fire or even an explosion It is strictly forbidden to operate the engine without an air filter, as this would cause damage to the engine. 1 Turn the screw counterclockwise to remove the filter cover 2 Use non-flammable solvents or cleaning agents with a high flash point to clean the filter element and let it dry completely. 3 Immerse the filter element in fresh lubricating oil and then press out the oil. 4 Put the filter element in the correct position again. 5 Install the filter cover and screw the screw back in clockwise.Manual_FX-4MS142_Int24_rev2

Spark plug maintenance To ensure regular operation of the engine, the ignition distance of 0.6 - 0.7 must be maintained and free of carbon deposits. 1 Carefully remove the spark plug connector. Do not pull on the cable but directly on the plug. 2 Use the spark plug wrench supplied to unscrew the spark plug. 3 Visually check the spark plug for damage or electrode burn-off. Remove the carbon deposits.

4 Check the gap with a feeler gauge and bend the electrode to the correct distance of 0.6 to 0.7mm 5 Check the spark plug washer and screw the spark plug in the first 2-3 threads manually first. 6 Mount the ignition cap back on the spark plug WARNING The spark plug must be screwed down tightly; otherwise, the engine runs hot and is damaged. Maintenance during storage of the machine If the engine is not to be used for a more extended period, the following maintenance must be carried out: 1 Open the fuel filler cap and drain the fuel completely. Operate the primary pump until the gasoline is completely removed from the fuel lines. 2 Open the oil cap and completely drain the lubricating oil as described 3 Adjust the crankshaft to top dead center (by pulling the starter) to ensure that the air does not cause corrosion Spark plug window Spark plug Spark plug connector cleaning of coal deposits Removing the spark plug 0.6~0.7mmManual_FX-4MS142_Int24_rev2

4 Wipe off all oil stains and clean the cooling fins. Place the device in a clean, dry, and well-ventilated place.

1. Remove the cutting blade (E) from the protective shield (F).

2. Clamp the knife in a vice. Sharpen the knife with a flat-file.

Please make sure that you keep the angle of the cutting edge. Move the blade only in one direction.

WARNING: If these steps are not taken, plaque will form in the carburetor

and cause difficult starting or permanent damage due to storage.

1. Perform all general maintenance recommended in the maintenance section of

2. Clean the exterior of the machine, drive axle, protective shield, and nylon cutting head.

3. Drain fuel from the fuel tank.

4. After fuel is drained, start the machine.

5. Let the device idle until the machine stops by itself. This cleans the

8. Pour 1 teaspoon of clean 2-cycle oil into the combustion chamber. Pull the starter cord

slowly several times to coat the internal components. Replace the spark plug.

9. Store the machine in a cool, dry place away from any ignition source such as

an oil burner, water heater, etc. TRANSPORT PROTECTION Make sure that the machine is well visible during transport to avoid fuel loss, damage, or injury. Use transport protection for metal sheets during transport and storage.Manual_FX-4MS142_Int24_rev2

1. Difficulties during commissioning

Spark plug Coal deposit Clean the spark plug. Adjust the gap 0.6~0.7mm Replace the spark plug other ignition coil defective flywheel magnet too weak replaced ignition coil replaced flywheel Weak ignition spark

Compression Too much gasoline in the combustion chamber Poor fuel or water in the tank Remove the spark plug and allow it to dry. Replace fuel The carburetor does not pump oil anymore. Oil line blocked Cleaning the carburetor and cleaning the pipes

regular oil supply but weak compression Piston rings do not close spark plug not tightly screwed on Cylinder head, not tight Incorrect valve clearance or ignition timing. replace screw tight Replace or adjust regular oil supply and good ignition spark Poor contact between ignition cap and spark plug Short circuit or on/off switch replace or check

2. Emergencies during operation

Situation Cause Solution the engine does not reach the speed Choke is in the wrong position. The exhaust system does not clog the air supply. Moving elements have worn ignition spark weakly too much valve clearance. Cylinder head sooty Open choke Replace exhaust system Check or replace ignition coil, flywheel. Spark plug Adjust valves Clean cylinder head Operating materials are leaking Lines to carburetor blocked Spark plug spacing incorrect Adjust replaced lines and carburetor gap Engine noises Wrong choke position Camshaft damaged Check Replace camshaft Carburetor leaking Failure of the check valve on the tank cap replaced the tank cap The carburetor gasket is worn out Replace carburetor or gasket

Have your purchased device repaired only by qualified personnel and only with original spare parts. This will ensure that the safety of the device is maintained. If you do not have the addresses of authorized service centers, please contact the sales office where you purchased the device. Please contact the manufacturer FUXTEC GmbH directly at www.fuxtec.de at any time regarding maintenance work and procurement of spare parts.

The warranty period is 24 months from the date of purchase. Please keep your proof of purchase in a safe place. Excluded from the warranty are wearing parts and damage caused by improper use, use of force, technical modifications, use of wrong accessories or non-original spare parts, and repair attempts by non-qualified personnel. Authorized dealers may only carry out warranty repairs.

Please contact your local community for the disposal of the device. Please dispose of all functional materials such as gasoline and oil in advance.Manual_FX-4MS142_Int24_rev2

Herewith we FUXTEC GMBH KAPPSTRAßE 69, 71083 HERRENBERG, GERMANY We herewith declare, Declare that the machine described below, due to its design and construction and in the version marketed by us, complies with the relevant essential health and safety requirements of the EC directives. That the following machine complies with the appropriate basic safety and health requirements of the EC Directive based on its design and type, as brought into circulation by us. This declaration becomes invalid if the machine is modified without our agreement. In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity

Measured sound power level Measured sound power level LPA =104dB Guaranteed sound power level: Guaranteed sound power level LWA=113dB Relevant EG-straightening thread: Applicable EC Directives: EC machine straightening thread 2006/42/EG EC Machinery Directive: 2006/42/EC EC Directive on Electromagnetic Compatibility (EMC) 2004/108/EC EC Directive of Electromagnetic Compatibility 2004/108/EC EC-directive thread Noise emission (2000/14/EWG & 2005/88/EC) EC Directive of noise emission (2000/14/EC & 2005/88/EC) applied harmonized standards: Applicable Harmonized Standards: EN 11806-1 EN ISO 14982 Manufacturer signature/date: Authorized Signature/Date/ Place:

L. Zirkler, 07.06.2023 The name and address of the person authorized to compile the technical documentation established within the community Name and address of the person authorized to compile the technical file, which must be established in the

INDOSSARE GUANTI (bordo affilato!).

WAARSCHUWING VOOR GEVAAR

Snijd niet met botte, gebarsten of beschadigde metalen messen. Controleer voor het werken het gebied op obstakels zoals stenen, metalen staven of andere voorwerpen. Als deze niet worden verwijderd Markeer deze positie zodat een botsing met het mes wordt vermeden. Leidingen kunnen vast komen te zitten aan de bladkop en flap of in de lucht worden geslingerd.

WAARSCHUWING VOOR GEVAAR

Gebruik de bosmaaier niet voor het zagen van bomen.

WAARSCHUWING VOOR GEVAAR

WAARSCHUWING VOOR GEVAAR

Varning! Brandfarliga material!

POLSKA WERSJA JEZYKOWA