RunFree Lite - Earphones SoundPEATS - Free user manual and instructions

USER MANUAL RunFree Lite SoundPEATS

1. Long Press the power button for 3 seconds to turn on the headset. Aer the white

light is on once, the headset enters the pairing mode, and the red and white lights ash alternately.

2. Turn on the bluetooth of your device, then select“SOUNDPEATS RunFree Lite” from

the bluetooth list to complete the pairing. SOUNDPEATS RunFree Lite Connected2 Reset English

1. Please insert the charging cable into the charging port to make the headset enter

the charging status.

2. Long press the power button for 3 seconds, the red and white lights will ash

alternately twice, a total of 4 seconds to restore factory settings.

3. Unplug the charging cable and turn it on, the headset reset is complete.English

2. Rotate the headset and nd the most comfortable position.

Product Diagram 2x1x 3x 1.5s 1x1.5s 1.5s1x5 Control English Power on Power O Play/Pause Volume- Volume+ Play Previous Play Next Enter/Exit Game Mode Answer/Hang up phone call Reject phone call Switch between two calls Activate voice assistant Manually: Long Press the power button for 3 seconds when the headset is turned o Automatically: No device connection for 3 minutes, the headset will automatically shut down Manually: Long Press the power button for 3 seconds when the headset is turned on Short press the power button Short press the volume "-" button Short press the volume "+" button Long press the volume "-" button Long press the volume "+" button Triple tap the power button Short press the power button Long press the power button for 1.5 seconds Double tap the power button Double tap the power button6 English

1. Connect with a Type-C charging adapter to charge .(Charging current is not

2. When not using for a long time, please charge it once every three months at

least. Q1: How to charge the headset? Method 1. Long press the volume button "+" and "-" at the same time for 3 seconds (long press the volume button "+" and "-" in the music and call state is invalid). Method 2. Turn o the Bluetooth of mobile phone , the headset will disconnect. Q2: How does the headset disconnect from the phone? Step 1. Turn on the headset, and connect device A to the headset. Step 2. Disconnect device A , and the headset enters pairing mode. Step 3. Connect device B to the headset. Step 4. Manually connect device A to the headset again. Aer manually connecting two devices for the rst time, they will connect automatically the second time. Q3: How can the headset connect to two devices at the same time? Q&AEnglish

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifcations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Statement IC ID - English: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference thatmay cause undesired operation of the device. - French: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.Deutsch Paarung

voltooid.Netherlands