Thermup 2.0 - Bottle warmer Lionelo - Free user manual and instructions

USER MANUAL Thermup 2.0 Lionelo

Dear Customer! In case of any questions or comments on the purchased product, please contact us: [e-mail] Producer: BrandLine Group Sp. z o. o. ul. A. Kręglewskiego 1, 61-248 Poznań, Poland Recommended operang condions Humidity: 50 - 80% Room temperature: 15 - 30°C Important informaon Please read this manual before using the product to familiarize yourself with its funcons and use it as intended. Failure to follow the safety instrucons and use not in accordance with the instrucons may result in damage to health. Keep this instrucon manual for future reference.

Do not repair or modify the device yourself. These operaons can only be performed by an authorized service centre.

2. This device is not a toy. Do not allow children to play

with it. Keep the device out of the reach of children.

The device may be used by children of at least 3 years of age and persons with reduced physical, sensory or mental capabilies, as well as persons without relevant‑ 6 ‑EN knowledge and experience in the use of the device, if they are supervised or have been previously instructed in the safe use of the device and the risks involved.

Cleaning and maintenance of the device can be performed by children aged at least 8 and under supervision. Keep the device and power cable out of reach of children below the age of 3.

5. The device is for domesc use only. The device is not

suitable for outdoor use. It should not be used for other purposes incompable with its intended use.

Do not let the power cord hang over the edge of a table or countertop. Do not bring the power cable into contact with hot elements. It should not be pulled over sharp edges.

Only connect the device to a mains socket outlet with a ground connecon. Make sure the power cord is properly connected to the power source.

Use a mains power supply corresponding to that indicated on the device label.

Use the device on a at heat-resistant surface. Do not move the device during operaon or when there is hot water in it.

10. Use only original accessories and spare parts.

11. Regularly check the device for damage. Do not use a

damaged device. Do not aempt to repair the device‑ 7 ‑ EN yourself – contact an authorized repair centre. If the mains cable becomes damaged, it should be replaced by the manufacturer to avoid danger.

12. Aer use, during assembly, disassembly and cleaning,

the device must be switched o and disconnected from the power supply.

Keep the device away from sharp edges and sources of heat and moisture. The device should not be exposed to direct sunlight.

Do not immerse the device or the power cord in water or other liquids.

15. Avoid overheang the device.

16. Before pung the bole in the heater and pouring in

the water, make sure it is rmly capped.

Make sure there is water in the device before switching it on. Never switch on the device if there is no water in it.

Hot water can cause severe burns. If there is hot water in the device, handle it with care.

When exposed to hot water, the surface of the device can become hot. It is important to remain cauous.

When the heated food has reached the desired temperature, remove the bole from the heater. Do not heat the food for too long.

Always check the temperature of the food before giving it to the baby.‑ 8 ‑EN

22. Allow the device to cool down before cleaning.

The device should be descaled regularly, every four weeks or so.

The heang element surface is subject to residual heat aer use. The product complies with the requirements of European Union direcves. In accordance with Direcve 2012/19/EU, this product is subject to separate collecon. The product should not be disposed of with municipal waste as it may pose a risk to the environment and human health. Return the used product to the recycling centre for electrical and electronic equipment. Parts list (g. A)

The switch is illuminated with a steady light when the device is switched on. The switch ashes when the device is in standby mode.

2. Decreasing the set value

Press and hold for approximately 2 seconds to acvate mute mode.

3. Increasing the set value

Press and hold for approximately 2 seconds to return to the factory temperature and me sengs.

Defrost/quick warm-up funcon Funcon with the opon to run for 3 to 8 minutes. Aer the selected me has elapsed, the device will beep ve mes and then automacally enter warming mode, maintaining the temperature of the food for 24 hours.‑ 9 ‑ EN

1. Place the bole or food container in the heater (g. 1).

2. Fill the heater with 80 ml of dislled water (g. 2).

In the display, select the Fast defrost/quick warm-up funcon (g. 3). Wait unl the indicator light comes on. NOTE Due to the high variety of textures of baby food, frequent mixing and controlling the temperature of the food being defrosted is recommended. Do not give milk/food to your child immediately aer defrosng. Frozen milk or food should not be heated. Milk or food can be reheated aer defrosng. Specics of the operang mode Quick warm-up Bole type Inial temper- -ature Amount of water Amount of milk 60 ml 120 ml 180 ml 240 ml Glass 4°C 80 ml 3 min 4 min 5 min 6 min 20°C 2,5 min 3 min 4 min 4,5 min Plasc 4°C 3 min 4,5 min 6 min 7 min 20°C 2,5 min 3,5 min 4,5 min 5 min Milk warming funcon The heang me can vary depending on the amount of milk or water and the inial temperature.

1. Place the milk or water bole in the heater (g. 1).

2. Fill the heater with 80 ml of dislled water (g. 2).

Select the temperature using the increase and decrease buons of the selected value (2, 3, g. B). The temperature range for this funcon is 37 - 60°C. The display shows the current uid temperature. NOTE It is advisable to give the milk to the baby immediately aer heang. Reheang the milk should be avoided. Always check the temperature of the milk before giving it to the baby (g. 5).‑ 10 ‑EN Food warming funcon

1. Place the food container in the heater (g. 6).

2. Fill the heater with 80 ml of dislled water (g. 7).

Select the temperature using the increase and decrease buons of the selected value (2.3, g. B). The temperature range for this funcon is 45 - 80°C. The display shows the current food temperature. NOTE Due to the high variety of textures of baby food, frequent mixing and controlling the temperature of the food is recommended (g. 9). Always check the temperature of the food before feeding (g. 10). Sterilizaon funcon Wash and thoroughly rinse the bole and accessories before disinfecon.

Place the item to be sterilized in the heater (g. 11). The bole should be placed boom up.

2. Fill the heater with 30 ml of dislled water (g. 12).

In the display, select the Sterilize disinfecon funcon (g. 13). Wait unl the indicator light comes on. Once the water has evaporated, the device switches o automacally. The disinfecon me is approximately 10 minutes. Temperature range and operang me of selected modes Note! If there is no water in the reservoir, the device will switch o automacally. Mode Temperature range Operang me Milk 37 - 60°C Up to 24 hours Food 45 - 80°C Up to 24 hours Sterilize 100°C Up to 10 min Fast 100°C 3-8 min Cleaning

Unplug the device aer each use and before cleaning. Allow the device to cool down before cleaning (g. 14).

2. Empty the device of water (g. 15).‑ 11 ‑

3. If food has been heated in the device, make sure there are no leovers on the boom.

4. Wipe the casing and the inside of the heater using a so damp cloth, then wipe dry with

a clean cloth or paper towel (g. 16). Note! Do not use scouring sponges, scouring agents or any corrosive substances or chemicals for cleaning. Descaling Regular descaling every four weeks is recommended to ensure that the device works properly.

1. Pour 50 ml of white vinegar and 100 ml of cold water into the device.

2. Switch the device on and then select the milk heang funcon. Allow the device to run

3. Leave the soluon in the device unl the scale dissolves completely.

4. Unplug the device before draining it.

Pour the soluon out of the device. Pour water into the device, rinse out the residual soluon and then empty the device. NOTE! Descalers based on citric acid can also be used. Do not use other types of descaler. The photos are for illustrave purposes only, the actual appearance of the products may dier from those shown in the pictures.