IAN 290615 - Lighting Livarno Lux - Free user manual and instructions

USER MANUAL IAN 290615 Livarno Lux

Case temperature at stated point d.c. DC Direct current For your safety Polarity of the power supply

Dispose of the packaging and de- vice in an environmentally friendly manner! Make-up Light Introduction Please be sure to carefully read the com- plete instructions for use. These instructions are part of the product and contain im- portant information on setup and handling. Always follow all safety instructions. Before using this product for the first time verify the correct voltage and that all parts are properly in- stalled. If you have any questions or you are unsure about operating the product, please contact the distributor or service centre. Please keep these in- structions in a safe place and pass them on to third parties if necessary.13 GB/IE Introduction / Safety Intended Use This light is only suitable for indoor use in dry and enclosed spaces. This device is only intended for use in a private do- mestic environment, not for commercial use. Any use other than that described above is prohibited and will result in product damage. It is further asso- ciated with dangers, e.g. short circuit, fire, electric shock, etc. Scope of delivery Check that all the parts are present and that the de- vice is in perfect condition immediately after unpa- cking. 1 Make-up light 2 Suction cups 1 Instructions for use Description of Parts

Output voltage / current: 4.8 W DC

24 V, max. 0.2 A Protection class: II / LED non-replaceable Safety Safety notes Damage due to failure to comply with these opera- ting instructions will void the warranty! We assume no liability for consequential damages! We assume no liability for property damage or personal injury due to improper handling or failure to observe the safety instructions!

AND SMALL CHILDREN! Never leave children unsupervised with the packaging material. The packaging material poses a suffocation hazard. Children fre- quently underestimate the dangers. Always keep children away from the product. This device may be used by children age 8 years and up, as well as by persons with re- duced physical, sensory or mental capacities, or lacking experience and/or knowledge, so long as they are supervised or instructed in the safe use of the device and understand the as- sociated risks. Do not allow children to play with the product. Cleaning and user mainte- nance must not be performed by children with- out supervision.14 GB/IE Safety / Before Use / Installing the light Avoid the risk of fatal injury from electric shock Check the lamp for possible damage before every use. Never use the light if it shows any signs of damage. CAUTION! A damaged supply cable poses a danger to life by electric shock. The device‘s supply cable can- not be replaced. If the cable is damaged, the appliance must be disposed of. The appliance contains no parts which may be serviced by the consumer. Before use, verify that the available mains volt- age corresponds with the required operating voltage of the item (see „Technical Data“). Never allow the live power leads and contacts to come into contact with water or other liquids. Never open any of the electrical equipment or in- sert objects into these. This will pose a risk of fatal injury from electric shock. Do not install the light on damp or conductive surfaces. Protect the product from sharp edges, mechani- cal loads and hot surfaces. Do not secure with sharp staples or nails. Always unplug the plug-in transformer from the socket before installation, removal or cleaning. Never touch the plug-in transformer with wet hands. Only use the individual parts supplied, other- wise all warranty claims will become invalid. In the case of damage, repairs or other pro- blems, please contact the service centre or a qualified electrician. Prevent fire and injury hazards This product does not contain any parts that can be serviced by the user. The LEDs cannot be replaced. If the LEDs cease to function at the end of their operational life, the entire item must be replaced. The installed LEDs are not suitable for dimmers or electronic switches. Do not look into the LED from a close distance during operation. Do not look at the LED with an optical instru- ment (e.g. magnifier). For your safety Install the light so that it is protected from dirt and excessive heat. Always be attentive! Always pay attention to what you are doing and use common sense. Never use the light if you are having difficulty concentrating or do not feel well. Familiarise yourself with all instructions and diagrams in this manual as well as with the light itself before use. To disconnect the lamp completely from the power supply, the plug-in transformer must be removed from the mains socket. Before Use Remove all packaging materials before first use. Please remove the protective film

from the light. The light should not be connected to the supply network while it is still in its packaging. Installing the light Note: Ensure that the installation area is clean, grease-free and dry. Otherwise the functionality of the suction cups may be impaired. Note: Ensure that a plug socket is located in close proximity to the installation area. Choose a suitable installation area (mirror etc.). Press the suction cup

onto the installation surface. Verify it is positioned correctly and securely. Clip the light

Ensure that the light

is positioned correctly.15 GB/IE Installing the ... / Maintenance and Cleaning / Disposal / Warranty and Service Connect the supply cable

with the plug-in transformer

via the connecting plug

Ensure that the polarity of the connecting plug

and the plug-in transformer

is correct. Plug the transformer

into the mains socket. If the suction cups

should alter their position over time, the light must be re-installed. Your light is now ready to use. Switching the light on/off Switch the light

Dimming the light Press and hold the touch button

until the light is set to the desired brightness. The light

dimmer function is continous (stepless). If the light

is switched off while it is dimmed, it will use the same dimmer setting when switched on again. Maintenance and Cleaning

ELECTRIC SHOCK! Before performing any work, first disconnect the light from the mains power. Unplug the plug-in transfor- mer

from the socket. Do not use solvents, petrol, etc. Otherwise the lamp will be damaged. Clean the light

with a dry, lint-free cloth. Disposal The packaging is made entirely of recy- clable materials, which you may dispose of at local recycling facilities.