METABO FSP 1000 S - Screwdriver

FSP 1000 S - Screwdriver METABO - Free user manual and instructions

Find the device manual for free FSP 1000 S METABO in PDF.

English EN ⬇ Download 💬 AI Question ❓ 10 questions ⚙️ Specs
📄

Document temporarily unavailable

The manual is currently being transferred to our new server. It will be accessible again in a few hours. Thank you for your patience.

Pick your language and provide your email: we'll send you a specifically translated version.
Product type Pneumatic paint spray gun
Brand Metabo
Model FSP 1000 S
Intended use Application of varnish and paint on suitable surfaces
Power supply Compressed air via 1/4" quick coupling
Spray pattern Adjustable round or wide (depending on equipment)
Paint volume adjustment Adjustment screw (5) for paint flow
Air flow regulation Adjustment screw (4) for fine adjustment
Spray distance Approx. 10 to 15 cm
Max. permissible operating pressure Stated in technical specifications (do not exceed)
Container capacity Gravity feed or suction feed container depending on model
Compatible materials Varnishes and paints; FSP 600 HVLP/LVLP models suitable for water-based varnishes
Cleaning Immediately after use; do not use halogenated solvents
Lubrication Oil moving parts; avoid lubricants with silicone
Safety Wear safety goggles, respiratory protection; do not point at people
Wear parts Nozzle and needle
Recommended accessories Use only genuine Metabo accessories
Maintenance By qualified personnel; use Metabo spare parts
Repairs Contact Metabo agency (addresses at www.metabo.com)
Disposal Follow national regulations for recycling

Frequently Asked Questions - FSP 1000 S METABO

How to adjust the spray pattern?
Use the adjustment screw (3) to switch from round to wide spray. Turn the nozzle head (2) to orient the spray horizontally or vertically.
How to adjust the paint quantity?
Turn the adjustment screw (5): open about 2 to 2.5 turns for a test, then adjust according to desired flow. Opening increases flow, closing reduces it.
What air pressure to use?
Operating pressure must not exceed the maximum permissible pressure stated in the technical specifications. Too high pressure causes fine atomization and a rough finish; too low gives a wavy appearance.
How to clean the spray gun?
Clean immediately after use. Do not fully immerse in solvent and do not use halogenated solvents. Oil moving parts regularly.
Can I use water-based paints?
Yes, but only with FSP 600 HVLP and FSP 600 LVLP models. Check the compatibility of your model.
What protective equipment to wear?
Always wear impact-resistant safety goggles, appropriate respiratory protection (activated carbon filter), and protective clothing. Hearing protection is recommended.
How to avoid nozzle blockages?
Clean the nozzle regularly. If the spray is irregular, clean it. Use filtered paints and follow cleaning instructions.
Where to find spare parts?
Use only Metabo spare parts. Visit www.metabo.com or contact the Metabo agency for parts lists and repairs.
Can the spray gun be used with flammable gases?
No. Never use oxygen or flammable gases as energy source. Use only purified compressed air free of condensate and oil.
How to store the tool after use?
Disconnect the air supply, clean it thoroughly, and store in a dry place out of reach of children. Protect from dust and moisture.

User questions about FSP 1000 S METABO

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

No questions yet. Be the first to ask one.

Download the instructions for your Screwdriver in PDF format for free! Find your manual FSP 1000 S - METABO and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. FSP 1000 S by METABO.

USER MANUAL FSP 1000 S METABO

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : METABO

Model : FSP 1000 S

Category : Screwdriver