EL230RGB MK2 - Laser pointer Laserworld - Free user manual and instructions

USER MANUAL EL230RGB MK2 Laserworld

1. Product and package contents 4

2. Preliminary warning notices 4

3. Initial operations, safety instructions 4

4. Working on the device 5

6. Warnings and other notices on the device 6

7. Device connections 7

8.1 Power on the Laser system

8.6 Turn off the Laser system

Final statement Technical data sheet Laser specicationsLaserworld EL-230RGB Laserworld EL-230RGB 4 / 28 5 / 28

1. Product and package contents

Please check if all listed parts are included and undamaged. Included in delivery: Laser system, power cable, keys, interlock bridge plug, manual

2. Preliminary warning notices

• Please use this device only according to these operating instructions.

• Do not use the device if there are any visible damages on housing, connector panels, power supplies or power cords.

• Never look directly into the light source of a laser projector. Danger of damage to the eyes or even blindness in extreme circumstances!

• This device must not be permanently connected to mains. Disconnect it from mains or use the power button to switch if o if not in use.

• Do not operate the device at high humidity, in the rain or in dusty environments.

• Protect device against dripping or splashing water. Do not place any liquid lled containers near to this device.

• Any warranty claims are void if the warranty label is removed or tampered with in any way.

3. Initial operations, safety instructions

• Make sure to use correct voltage; see information on device & in this manual.

• Make sure that the device is not connected to mains during installation.

• Installation has to be done by technical experienced and qualied persons according to safety regulations of the respective country.

• Always ensure that maximum permissible exposure (MPE) is not exceeded in areas accessible to the public or members of staff.

• In some countries an additional inspection by technical control institutes could be necessary.

• Connect an easily accessible interlock connector or circuit breaker to the projector.

• The power supply should be easily accessible.

• When installing the laser mount it with a minimum distance of 15 cm from walls and objects.

• For safe setup e.g. on walls or ceilings please use a safety cord. The safety cord should be able to withstand tenfold the weight of the device. Please follow the accident prevention regulations of professional associations and/or comparable regulations for accident prevention.

• If the device has been exposed to great temperature changes, do not switch it on immediately. Condensation (or any moisture / water formed) may damage device.

• Never use dimmer, RC or other electronically switched sockets. Whenever possible, do not use the laser projector together with large appliances (especially fog machines) on the same mains!

• Ensure sufcient ventilation and do not place the device on any warm or heat radia- ting surface. Especially the ventilation openings must not be covered!

• Ensure that device does not get overheated. Make sure that the device is not exposed to spotlights (especially moving heads). Heat of spotlights could overheat laser in a little while and leads to a degradation of performance.

• This unit is intended for indoor use only.

4. Working on the device

• This product has no user serviceable parts inside and should only be maintained and serviced by a qualied engineer.

• Be sure that the mains plug is not connected to the power supply while installing.

• Take off all reecting things like rings, watches etc. before starting to work with or at the projector.

• Only use non-reecting tools to work on device.

• Wear protective clothing (like glasses, gloves etc.) accor- ding to laser power and wavelength of the laser.

• Moisture and heat can reduce lifetime of the laser system dramatically and expires any warranty claim.

• Quick on/off switching of this device will reduce durability of the laser diode dramatically.

• Avoid sharp knocks and shocks to this device and ensure sufcient protection during transportation. Look after your Laserworld product.

• To increase durability of your laser, protect device against overheating:

1. Always ensure sufcient ventilation.

2. Do not face spotlights (especially moving heads) to the device.

3. Check temperature after approx. 30 minutes with each new installation. If necessary

install the projector at a place with different temperature.

4. Keep the device dry. Protect it from moisture, rain and damp.

5. Switch off device when it is not needed. Diodes are switched on and can wear out

even if there is no visible laser output.

6. Please ensure the fans and heatsinks are clear from dust and debris otherwise the

risk of overheating may occur. If the unit and airways appear to be blocked then please contact a qualied service engineer to maintain and service the product.

• The devices of the Ecoline Series are not meant for professional applications. They are not suitable for 24/7 operation.

• Removal of the warranty label as well as damages to the device caused by impro- per handling, neglect of the safety instructions and service notes will void the warrantyLaserworld EL-230RGB Laserworld EL-230RGB 6 / 28 7 / 28 Laser radiation! Avoid exposure to beam Caution of ra- diation if cover is removed Power supply & consumption Model type Wavelength Output power Production year Use in enclosed spaces only! Laser class 3B

6. Warnings and other notices on the device 7. Device connections

DMX address, operation mode Interlock DMX out DMX in ON/OFF switch key switch mains connection microphoneLaser emission LEDLaser aperture warning labeltrim pot for music-sensitivity

8.1. Power on the Laser system a. Connect the power cable to the device and then to the mains b. Insert the key into the key switch and turn it to the„ON“ position c. Connect the Interlock Connector with the Interlock Port at the back of the device d. Press „ON“ to switch the device onLaserworld EL-230RGB Laserworld EL-230RGB 8 / 28 9 / 28 8.2. Automatic mode, Stand-alone operation Set the device to auto mode:

8.3. Music mode, Sound-to-light operation Set the device to music mode:

Control the music sensitivity with the trim pot at the front panel. The LED is ashing when the device is triggered. 8.4. DMX-512 mode Switch 10 must be set to „o“, the other switches are used for setting the DMX address:

Connect a DMX controller to operate the laser. Use the switches 1 - 9 to set the DMX address of the laser. Each switch represents a number. To dene a number use the preceding number and multiply it by 2: Switch 1 2 3 4 5 6 7 8 9 10 Number 1 2 4 8 16 32 64 128 256 Mode Switch

The laser uses 9 DMX channels, so make sure that the next device uses an address that doesn’t overlap with this range. Channel Value Function 1 0 - 49 Laser off

2 0 - 255 Pattern selection 3 1 - 10 Center Position on X axis

11 - 255 X axis positioning

4 1 - 10 Center Position on Y axis

11 - 255 Y axis positioning

5 0 - 255 Scanning speed 6 0 - 255 Dynamic pattern speed 7 0 - 255 Zoom / size 8 0 - 255 Color 9 0 - 255 Color segment Please note that a pattern can not necessarily be combined with each effect. 8.5. Master-Slave mode This mode will allow to link up several units together without a controller. Choose a unit to function as Master, set the dipswitch to select Sound mode or Automatic mode. The other units must be set to slave mode (Switch 10 must be set to „off“). Use standard XLR cable to chain your units together via the XLR connector on the rear of the units. After the slave units are turned „on“ they will reset and start in Slave mode to mirror the behaviour of the master unit. 8.6. Turn laser of To turn off the device switch it off („OFF“), switch the key to „OFF“ and discon- nect the power cable from the mains.Laserworld EL-230RGB Laserworld EL-230RGB 10 / 28 11 / 28 Final statement Laserworld products are tested and product packaging is inspected before leaving our warehouse. Users must to follow the local safety regulations and warnings within this manual and adhere to any regulations within its place of use. Damages through inappropriate use will void any liability or warranty of our products. Due to continual product developments, please check for the latest update of this product manual at www.laserworld.com. If you do have any further questions, then please contact your dealer/place of purchase or use our contact section on our website. For service issues, please contact your dealer/place of purchase and ensure only genuine Laserworld spare parts are used in any service repairs. Errors and omissions excepted and products are subject to change. Laserworld (Switzerland) AG Kreuzlingerstrasse 5 8574 Lengwil SWITZERLAND Registered oce: 8574 Lengwil / Switzerland Company number: CH-440.3.020.548-6 Commercial Registry Kanton Thurgau CEO: Martin Werner VAT no. (Switzerland): 683 180 UID (Switzerland): CHE-113.954.889 VAT no. (Germany): DE258030001 WEEE-Reg.-No. (Germany): DE 90759352 www.laserworld.com [e-mail] representative according to EMVG: Ray Technologies GmbH Managing Director: Martin Werner Mühlbachweg 2 83626 Valley / Germany Inhalt