IAN 302568 - Lighting Livarno Lux - Free user manual and instructions

USER MANUAL IAN 302568 Livarno Lux

Assembly, operating and safety instructions

NL BE

LED-PENDELLAMP

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

FR BE

GB / IE Assembly, operating and safety instructions Page 11

Intended use......Page 12

Scope of delivery....Page 12

Parts description Page 13

Technical data......Page 13

Safety Page 13

Safety instructions......Page 13

Preparation......Page 14

Required tools and material Page 14

Mounting the light Page 14

Initial use....Page 14

Changing the bulb ......Page 14

Maintenance and cleaning......Page 15

Disposal Page 15

Information......Page 15

Warranty Page 15

Declaration of conformity....Page 15

Manufacturer / Service Page 16

List of pictograms used
	Please read the operating instructions! War	Risk of electric shock!
	Earth conductor The LED light is not dimmal
	Volt (AC)		This light is only suitable for indoor use in dry and enclosed spaces.
	Hertz (frequency) Safe working
	Watt (effective power) Warning - hot surfac
	Observe the warning and safety instructions!		Dispose of packaging and device in an environmentally-friendly way!
	Switching cycles LED life

ED pendant lamp

Introduction

Congratulations on the purchase of your new device. You have selected a high quality product. Please be sure to care-

fully read the complete instructions for use. Fold out the page with the illustrations. These instructions are part of the product and contain important information on setup and handling. Always follow all safety instructions. Before using this product for the first time verify the correct voltage and that all parts are properly installed. If you have any questions or you are unsure about operating the product, please contact the distributor or service centre. Please keep these instructions in a safe place and pass them on to third parties if necessary.

Intendeduse

This light is only suitable for indoor use in dry and enclosed spaces. The light can be fastened to any normally inflam-

mable surface. This product is only intended for private household use, not for commercial purposes.

- Scope of delivery

Check immediately after unpacking that the parts are complete and that the product is in proper condition.

1 LED pendant lamp, Model 14130205L

5 Lampshades

2 Wall plugs

2 Screws

2 Protective tubes

5 LED light bulb

1 Set of assembly instructions and instructions for use

Partsdescription

1 Wall plug
2 Mounting bracket
3 Locating screw
4 Screw
5 Protective tube
6 Mains connection cord (external)
7 Terminal block
8 Terminal housing
9 Socket
10 Lamp shade
11 Lamp ring
12 Light bulb

●Technicaldata

Item no.: 14130205L

Socket: 1 x E14

Operating voltage: 230-240V\~50Hz

Rated power: 5 x max. 5 W

Light bulb: 5 x LED-light bulb, E14

Protection class: I

Degree of protection: IP20

Safety

Safetyinstructions

Damage due to failure to comply with these instructions for use will void the warranty! We assume no liability for consequential damages! We assume no liability for property damage or personal injury due to improper handling or failure to comply with the safety instructions! Only use the included parts, using other parts will void the warranty.

- hit device may be used by children aged 8 years and up, as well as by persons with reduced physical, sensory or mental capacities, or lacking experience and / or knowledge, so long as they are supervised or instructed in the safe use of the device and understand the associated risks. Do not allow children to play with the

appliance. Cleaning and user maintenance should not be performed by children without supervision.

Avoid the risk of fatal injury from electric shock

■ Ensure that a qualified electrician, or a person trained to carry out electrical installations, performs the electrical installation.
We assume no liability for property damage or personal injury due to improper handling or failure to observe the safety notices!
■ Never use the light if any defects have been identified.
Prior to installation, remove the fuse or switch off the circuit breaker 0 setting in the fuse box.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
■ Ensure that the light does not come into contact with water or other liquids under any circumstances.
Prior to installation verify the mains voltage on site corresponds with the operating voltage required for the light (see "Technical data").
Be sure not to damage any wires during installation.
The length of the pendant light is not adjustable.

Prevent fire and injury hazards

To prevent burns, be sure the light is switched off and cooled down before touching it.
Do not mount the light to a damp or conductive surface.
Do not leave the light or packaging material lying about unattended. Plastic film or bags, plastic parts, etc. are dangerous for children to play with.

The LED light is not dimmable.

Do not look directly into the illuminant (lamp, LED, etc.). Do not look into the illuminant (lamp,

Safety/Preparation/Mounting the light/Initial use/Changing the bulb

LED, etc.) with an optical instrument (e.g. magnifier).

This light is only suitable for indoor use in dry and enclosed spaces.

Safe working

• Install the light so it is protected from moisture, dirt and extreme heating.
  Always be attentive! Always pay attention to what you are doing and use common sense. Never use the light if you are having difficulty concentrating or do not feel well.
  Familiarise yourself with all instructions and diagrams in this manual as well as with the light itself before use.

● Preparation

• Required tools and material

The tools and materials specified are not included. This information and these values are non-binding and are only provided as a reference. The nature of the material is determined by the individual local conditions.

• Pencil / marking tool
• Voltage tester
• Screwdriver
• Electric drill
• Drill (approx. ∅ 6 mm)
• Side cutting pliers
• Ladder

- Mounting the light

WARNING! RISK OF ELECTRIC SHOCK!

Prior to installation, remove the fuse or switch off the circuit breaker in the fuse box (Position 0) (fig. A).

☐ Remove the locating screws 3 visible at the side of the terminal housing 8 and remove the mounting bracket 2 at the back.
☐ Use the slotted holes for the screws 4 on the mounting bracket 2 to mark the bores. Now drill the mounting holes (approx. 6 mm, depth approx. 30 mm). Be sure not to damage the supply line.
☐ Insert the wall plugs 1 into the drilled holes.
☐ Fasten the mounting bracket 2 with the provided screws 4.
☐ Pull the protective tube 5s over cables L and N of the mains connection cord (external) 6.

Note: Be sure to correctly connect the individual leads on the mains connection cord (external) 6: live wire, black or brown = symbol L, neutral wire, blue = symbol N, earth wire, green-yellow = symbol ⊥.

☐ Now use the locating screws 3 to connect the light to the mounting bracket 2.
☐ Loosen the lamp rings 11 from the bulb socket 9.
□ Completely remove the protective film from the lampshades 10.
Place a lampshade 9 onto every bulb socket 10 and use the lamp rings 11 to secure them in place.
☐ Use a clean, lint-free cloth when inserting the light bulbs 12.
☐ Screw the light bulb clockwise into the bulb socket 9.

Ensure that they are positioned correctly.

☐ Reinsert the fuse or switch the circuit breaker back on (fig. C).

Your light is now ready to use.

- Initial use

☐ Use the wall switch to switch the light on or off.

- Changing the bulb

WARNING! RISK OF ELECTRIC SHOCK!

When replacing the light bulbs, first disconnect the

light from the mains. To do so, remove the fuse or switch off the circuit breaker in the fuse box 0 position (fig. A).

⚠️ CAUTION! RISK OF BURNS DUE TO HOT SURFACES!

Allow the light to cool completely.

Only replace the light bull once they have fully cooled down.
☐ Use a clean, lint-free cloth to replace the light bulbs 12.
Carefully turn the defective light bulb anti-clockwise out of the bulb socket 9.
☐ Only use the light bulbs specified in chapter "Technical data".
Carefully screw the new light bulb2 clockwise into the bulb socket 9. Ensure that it is positioned correctly.
☐ Reinsert the fuse or switch the circuit breaker back on (fig. C).

● Maintenance and cleaning

WARNING! RISK OF ELECTRIC SHOCK!

Disconnect the light from the mains circuit before cleaning. To do so, remove the fuse or switch off the circuit breaker in the fuse box 0 position.

• Allow the light to cool off completely.
  ■ Only clean using a dry, lint-free cloth a brush or a clean brush.
  Do not use solvents, spirit or similar substances. They could damage the light.
  ☐ Replace the fuse or switch on the circuit breaker (Position I) inside the fuse box.

●Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.

Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning:

1-7: plastics / 20-22: paper and fibre-board/80-98: composite materials.

The product and packaging materials are recyclable, dispose of it separately for better waste treatment. The Triman logo is valid in France only.

Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.

To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.

Information

Warranty

You receive a 36 month warranty on this product, valid from the date of purchase. The appliance has been carefully produced under strict quality control. Within the warranty period we shall rectify without charge all material and manufacturing defects. In the event of a defect during the warranty period, please send the product to the service address listed, indicating the following item number: 14130205L.

Wear parts (such as bulbs) and damage caused by improper handling, non-observance of the operating instructions or unauthorised interference are excluded from the warranty. The performance of services under the warranty does not extend or renew the warranty period.

Declaration of conformity

This product meets the requirements of applicable European and national directives. Conformity has been demonstrated. The relevant declarations and documents are held by the manufacturer.

Manufacturer / Service

Please have your receipt and the item number (e.g. IAN 12345) ready as your proof of purchase when enquiring about your product.