3TS995BT - Washing machine BALAY - Free user manual and instructions

Product type	Washing machine
Brand	BALAY
Model	3TS995BT
Required repair tools	Torx T20 screwdriver, torque wrench 20-100 Nm, fine needle nose pliers, cutting pliers, flathead screwdriver (3.5 mm and 5.5 mm)
Available spare parts	Top, control panel, product drawer, drawer handle, door, door components, door gasket, door lock, drum light, pump cover, front panel
Risk levels	DANGER, WARNING, CAUTION
Danger symbols	Electric shock, explosion, cut, crushing, hot surfaces, magnetic field
Repair conditions	Appliance disconnected from mains, powered off and disconnected from water supply
Safety instructions	Wear protective gloves, secure appliance against falling, perform an electrotechnical test after repair (according to VDE 0701)
Routine maintenance	Remove and clean product drawer, check door gasket, clean pump filter
Part accessibility	Disassembly possible of top, control panel, front panel, door
Provided documentation	Detailed repair manual (505 pages) containing assembly/disassembly instructions
After-sales service	Contactable for additional questions
Recommended tightening torque	Door gasket: 3.4 Nm

Frequently Asked Questions - 3TS995BT BALAY

How to remove the top of the Balay 3TS995BT washing machine?

Remove the screws at the rear (1), then push the top towards the back (2) and lift it (3). For reassembly, follow the reverse order. Make sure the appliance is unplugged and powered off.

How to replace the door gasket?

First remove the product drawer, the door, the pump cover and the front panel. Loosen the clamping ring with a plastic tool, remove the old gasket and install the new one. Tighten the tension ring to 3.4 Nm.

How to clean the product drawer?

Open the product drawer, press the latch (1) to release it, then pull it outward (2). Clean it under warm water and put it back by pushing until it clicks. Do not use abrasive products.

How to access the control panel?

First remove the top and the product drawer. Then unscrew the screws (1) and remove the fixing elements (2, 3). Disconnect the connector from the control unit, then remove the panel. Wear protective gloves against sharp edges.

What tools are needed for repairing this washing machine?

The main tools are: a Torx T20 screwdriver (with hole for security tamper-proof screws), a torque wrench (20-100 Nm), an angled fine needle nose pliers, cutting pliers and insulated flathead screwdrivers (3.5 mm and 5.5 mm). Use appropriate tools to avoid damaging the appliance.

How to change the drum light?

Remove the top, the product drawer and the control panel. Take out the drum light holder, disconnect the electrical connections and remove the old light. Mount the new one in reverse order. Unplug the appliance before any intervention.

How to remove the washing machine door?

Open the door, remove the screws (1) on the hinges, then lift the door to free it. Be careful of the hinge area: risk of finger crushing. Wear protective gloves. Reassembly is in reverse order.

What safety precautions to take before repair?

Before any repair, unplug the appliance from the mains and wait at least 60 seconds. Disconnect the water supply. Do not insert fingers into the hinge area. Secure the appliance against falling and wear protective gloves. After repair, perform a safety test according to VDE 0701.

How to replace the door lock?

Disconnect the door lock connector, release it from its housing and remove it. For installation, follow the reverse order. After replacement, have the installation checked by a qualified electrician and perform an electrotechnical test before commissioning.

Where to find the repair manual for the Balay 3TS995BT?

The complete repair manual (505 pages) is available free of charge in PDF format on sites like notice-facile.com. It contains detailed instructions for disassembly, reassembly and safety instructions. You can download it by selecting your language.

USER MANUAL 3TS995BT BALAY

3.2 CmHa Ha facadnnaheI 7

3.2.1 CbJIHe Ha pacaHnnaHn 7
3.2.2 MoHTIpaHHe Ha fapaHnnaHn 7

3.3 CmHa Ha YekMeJKeTo 3a nepuHn npenapat 8

3.3.1 CbAJIHe Ha YekMeDKeTo 3a nepuHn npenapat 8
3.3.2 MoHTIpaHe Ha YeKMeJKeTo 3a nepuHn npenapat.. 8

3.4 CmHa Ha dpkKaTa Ha YekMeJKeTo 3a nepnne HpnapaT.. 9

3.4.1 CbAHe Ha dpBkKaTa Ha YeKeMeJKeTo 3a nepnEn npenapaT.. 9
3.4.2 MoHTnpaHe Ha DpbXkKaTa Ha YekMeXdKeTo 3a nepnEn npenapat .9

3.5 CmHa Ha BpaTata 10

3.5.1 ⅢBaKaDaHe Ha BpaTaTa.. 10
3.5.2 MoHTnpaHe Ha BpaTaTa.. 10

3.6 CMraHa HA KOMnOHeHTnte Ha BpaTata 11

3.6.1 CbajHe Ha KOMnoHEnTe Ha BpaTaTa 11
3.6.2 MoHTIpaHe Ha KOMNOHEHTITe Ha BpaTaTa 11

3.7 CmHa Ha ynnbTHHeHMeTo Ha BpaTaTa 12

3.7.1 CbaJnHe Ha yIbTHHeHHeTo Ha BpaTaTa 12
3.7.2 MoHTIpaHe Ha yNbTHHeHMeTo Ha BpTaTa 15

3.8 CmHa Ha KInoua Ha BpaTaTa 16

3.8.1 CbJIaHe Ha KIOUaIaNkata Ha BpaTata. 16
3.8.2 MoHTnpaHe Ha KIOUHAnKaTa Ha BpaTata 17

3.9 CMnHa Ha oCBeTneHMeTo Ha 6apa6aHa. 18

3.9.1 CbaJrHe Ha oCBetJeHMeTo Ha 6apa6aHa 18
3.9.2 MoHTnpaHe Ha OCBeTJIeHMeTo Ha 6apa6aHa 18

CIMBOHTE3aONACHOCTCa CIMBOHNUH N3o6paXeHNA, KOHTO DaBaT INDINKAUHA 3a BnDa ONACHOCT.

BTo3n DOKyMeHCTe H3N013BaT CNEdHInTe CMBOIN 3a OnaCHOCT:

HakpainnK Torx TX20 cOTBOP,6,30MM (14") 152mm,3a BnHTOBc [00341272]

N3nCKBaHe:

YpeBte n3KIOUeHOT 3aXpaHbHeTo.
YpeBTe N3KJIoueH OT BOIOcHbIteHnHaT MpeXa.

3.1.1 CbJIaHe Ha ropHna pa6oTeH nIOT

1.CBaNETe BnHTOBete(1).
2. 136yTaIe rOpHnpa6oTeH nnot KbM 3aHnKpAHa ypeJa (2).
3. PnemecTe rOpHna paBoTeH nnot HArope (3), 3a Da rO cbAnnte.

3.1.2 MoHTnpaHe Ha ropHna pa6oTe Hnnot

MoHTnpaTaTe B o6paTeH peJ.

PemOH

3.2CMHaHaΦacHnaHn

BHNMATEJIHO

Octpn p60Be Ha Kopnycal

HapaHbAHmO Tnp3BaHe

Hocete npedna3n pbkabu.

EDYNPPEKDEHME

Ppnnb3BaHe Ha HAKNOHEn ypeNi!

KoctHn ppaKtpn/HapaHbAHHN O TnpMa3BaHe

YkpeneTe ypeDnTe cpeu npnnB3BaHe.

BHIMATEJIHO

Pnck OT nadaun yactn npadn pa3xna6eHN BHTOBE!

HapaHbHe npa nadaunact

3akpenete KOMNOHHTa, Taka Ye da He naHe.

BHIMAHHEI

Pnck OT naaun yactn npaepa3xna6eHN BnHTOBE!

NopeHa npTu qactn Ha ypeHa nnB Doma Ha KneHTa, Hap. bHo

10.

3akpenete KOMnoHeHTa, TaKa Ye Da He naHHe.

N3nCKBaHe:

YpeBt E N3KIOUeHOT 3aXpaHbHeTo.
YpeDbTe n3KIOUeH OT BOOCha6DHTeHnHaT aMpexka.
FopHnT pa6oTeH nnot eCBaneH.→6
YekmedkeTo3a nepunHn npenapat cBaneHo.→8

3.2.1 CbAaHe Ha aacadnnaHc

1. 1.CBANETEBHTOBETE(1).

2.Ocbo6oTe KpenexHnTe eJeMeHTn (2,3).

2.Ocbo6oTeE uencenHTo CbeHNHeHHe Ha KOHTponnHa 6nK.
3. CbaneTe paacnnaHn naHn.

3.2.2 MoHTpaHHe Ha paacnnaHn

MoHTnpaTBeBobpaTeHpe.

PemOH

3.3CMHaHa YekMeJKeTo 3a nepuH npenapaT

N3nCKBaHe:

YpeBbTe H3KnIOueHOT 3axpaHBAHeTo.
YpeBt E n3KIOUeH OT BOOCha6DnTeHnHa MPeka.

3.3.1 CbānHe Na YekMeJxKeTo 3a nepuH npenapat

1. ⅠnterTne TeueKMeDxkeTo 3a nepiIne npenapat.
   2.1.HaTnCHete HADONY Bbpxy NOIIOKKaTa(1).

2.CbaneTe YekMeJKeTo 3a nepuInen npenapat (2).

3.3.2 MoThnpaHe Ha YekMeJKeTo 3a nepuIne npenapat

MOnTpaaTeB06paTeHpe.

PemOH

3.4 CmHa Ha DpbkkKaTa Ha YekMeJKeTo 3a nepnneH npenapaT

N3nCKBaHe:

YpeIbTe N3KIOUeHOT 3aXpaHbHaHeTo.
YpeBt E n3KIOUeH OT BOOChA6DITENHaT MpeXa.
YekmeJeKeTo 3a nepuHnI npenapat e cBaaneHo. 8

3.4.1 CbAJIHe Ha dpBxKkata Ha YekMeJKeTo 3a nepuJeH npenapat

1.OcbobodTe Kpenexhnte enemHTN.

2.CBaIeTe pBxKkTaHa YekMeJKeTo 3a nepuHn npenapat.

3.4.2 MoTHnpaHe Ha DpBkkKaTa Ha YekMeXdKeTo 3a nepnne npenapat

MOHTPauTe B opaTeH peI.

PemOH

3.5 CMHa Ha BpTaTa

BHIMATEJIHO

OTBOpTe 0bIacTHa naHTnTe!

Ppema3BaHe/3axBaUaHHe Ha npbCTNTe

He nocaraTe KbM ObnactTa Ha naHTnTe.

Hocete npedna3n pbkauu.

N3nCKBaHe:

YpeBte n3KNIOUeHOT 3aXpaHbHeTo.
YpeIbTe n3KJIoueH OT BoDcHa6nTEnHaTa MpeXa.
Bpatata e otbopeha.

3.5.1 NbBaxDaHe Ha BpaTata

1.

BHIMAHHEI

Pnck OT naaun yactn nopadn pa3xna6eH BuHTOBe!
NoBpeHa npTuHacn Ha ypeHa NIN B DoMa Ha KNHeHTa, HAp.
HHTO.
3akpeneteKOMnoHeHTa,TakaYeHaHe naHe.

BHIMATEENHO

Pnck OT naaun yactn nopadn pa3xna6eHN BuHToBe!

HapaHbAhe npa ndaun yactn.
3akpenTe KOMnoHEHTa, Taka Ye da He naDHe.

CbaTe BHTOBete(1).

2.ИЗБаДЕТЕВРАТАНОРЕ.

3.5.2 MoHTIpaHe Ha BpaTaTa

MoHTnpaTBeBobpaTeHpeI.

PemOH

3.6CMHaHa KOMNoHEnTHe Ha BpaTaTa

BHIMATEJIHO

OTBOpTe 06nactTa Ha naHTnte!

Ppema3BaHe/3axBaUaHHe Ha npbCTNTe
He nocaraTe KbM ObnactTa Ha naHTnTe.
Hocete npedna3HN pKabu.

N3nCKBaHe:

YpeBte n3KNIOUeHOT 3aXpaHbHeTo.
YpeIbTe n3KJIoueH OT BoDcHa6nTEnHaTa MpeXa.
Bparatae cbaneha. 10

3.6.1 CbAJaHe Ha KOMNoHEnTHe Ha BpaTaTa

Pa3rno6eTe BpaTata OTBbH HABbTpco.

3.6.2 MoHTnpaHe Ha KOMNOHEHTUte Ha BpaTaTa

MOHTnpaTBeB o6paTeH peI.

PemOH

3.7CMHaHa yyIbTHHeHMeTo Ha BpaTaTa

BHIMATEJIHO

Octpn y6b0e HaopnHbAHHoT o npor3BaHe

HocTe npedna3n pkbauu.

BHIMATEJIHO

Pnck O T npaun qactn nopadn pa3xna6eHn BnHTOBe!

HapaHbAHe npaPi ndaun Yactn.

3akpenete KOMnoHEHTa, Taka Ye da He naHe.

BHIMAHHE!

Pnck OT nadaaun yactn nopadn pa3xa6eHN BnHTOBe!

NopeHa npyn TaCn Ha ypeHa nn B doma Ha knneHtA, Hap. bHo

TO.

3akpenete KOMnoHEHTa, Taka He naHe naHe.

M3NCKBaHe:

YpeDbTe N3KJIIOUeHOT 3aXpaHbHaHeTO.
YpeBTe n3KIOUeH OT BDOChA6nTeHnHaT MpeXa
YekmendkeTo 3a nepunHn npenapaTe cBaneHo.→8
BpaTaTa e cBaNeHa.→10
KanakbHa nomnatae cBaaneH.→19

3.7.1 CbJIaHe Ha yIyIbTHHeHnETo Ha BpaTaTa

1.

I PEPDYNPPEXDEHNE

Ppnnb3BaHe Ha HakoNoHenuypeqn!

KocTHnΦpaKTypH/HapaHbAHnO Tnpema3BaHe

Ykpenete ypeDnTe cpeu npnnb3BaHe.

NoBnHHeTe ypea Otnpe.

1. Paxna6e BnHToBte B DonHa TaC HnpeHnnaHn (1).

3.CnycheTe ypeHaHaoNy.

PemOH

1. OTePahETe BnHToBete B 6bnaCTa Ha nomrata (2).5.1. Pa3Xna6e BnHToBete ot3ad Ha ypeDa (1).

Pnck OT naaun yactn nopadn Hnpabunen MOHTax!

HapaHbBaHe nn nobpeXdaHe Ha ypeHa.

HaterHete npTnCKaunna pBCTen Ha yNtHeHMeTo Ha bpaTaTa 3.4 Nm.

MoHTnpaTBeBobpaTeHpe.

PemOH

3.8CMHaHaKIOHaBpaTaTa

Kato npo3BODIen HnE CME 3aBbJIeHN Da npoeOCTaHIM Ha nOtp6bIeTIneTKe KaTO
peepBa HA qct KIOUAnJa 3a Bpata, BIKIOENTENHO IHCTpyKJy3a 3ePOMH B cBOT-
BETCTNE C PerlAmHeTA (EC) 2019/2023. BxMxN XcAHH DA OtBEKIXHM OBeAH,
CneL CMHATA Ha KNIOChkATA Ha Bpata, e Heo6XoDmO Da ce N3BbpHn ENEKTPO
TEXHnCeEA NPoBepKa 3a BeOnaHocHT ONBAINPHINAP AN ENEKTPOEXHK, PnEDype
Bt Da 6bJe NCHAT B EKCNIOAaTUR. ToBA NIIe TpRABa DA bSe CnotBpDeHa KBA
InfKnFauCa CBnAcho CneuPhnHnTe 3a CTpaHATA 3aKOHn, paoNpeBn C tAHdaptN.

OTIACHOCT

Pnck OT TKOB ydap npaH nuactn noHanpeKeHne!

Onachoc3aXUBOTaOTOKOByapBCnyuHa HenpaBUNeH peMOHT

EneKtpnue TaeTn Tp8Ba da ce pmoHTnpaT OT KbaHnHnPAH neneKtpoTeKHn
CnepeMOHTaT6BaJaCeN3bPmI npOBepKa 3a 6e3oNaCHOCTcbrnacoVDE0701nnBcOBTBeCTBHe CbcCneumHnHnTe 3a cTpaHATApnope6M.

BHNMATEJIHO

Octpn p6oBe Ha Kopnycal HapaHaaHnO t np3BaHe Hocete npedanshpKaBn

PTEUYPTPEJDEHNE

Ppnnn3BaHa He HaknoHneH ypeD1 KocTHn fpaKtpyn/HapaHbAaBOn t npMa3BaHe Ykpenete ypeDnre cpeuyn pnpNbBaHe.

BHIMMATENHO

Pck ot nadaa qactn npadpa3xna6eHN BHTOBe! Hapanahe npadn nadaa qactn. 3akpenete KOMPOHETA, taKa ye da He naHe.

BHIMAHINE!

PCKOTnadaunyactnnapnpa3xnaabeHNBHHTOBe!
NopedaHnpyruchnHa ypea HbDOMa Ha KIneHTA,HaNP.1bHO- 3akpeneteKOMnoHEHTA,Taka Ye Na He naHe.

m3nckbaHe:

YpeBt en3KNIOueHOT 3aXpaHbHaHeTO.
YpeBt en3KIOHcH OT BOIOCHA6dIeNTHaT MaPexa.
Ypeinte ca CBO6oHNO IOCTbHN.
TogHnT paoboteH nnot e CBaneH.→6
ΦacadHnT nHaen e CBaHeN.
BpaTaTa e cBanHe.→10
O6Tgauunr npbctHe cBaenH.
PpeDnT nHeI e CbaJeH.
YnnbTheHHeTo Ha BpaTaTa e CBAneHO.

3.8.1 CbānHe Ha KlnouaKaTa Ha BpaTaTa

1.ИЗкючeteцencelaHaKIOUAnkataHaBpaTaTa.
2.Ocbo6oJeTe KIOHAnKaTa Ha BpaTata.

3.CbaneTe KIOHuaKata Ha BpaTata.

PemOH

3.8.2 MoHTmpeHa KJIIOUaJIkAraHa BpaTaTa

MOHTnpaTBeBobpaTeHpe.

MOnHTnpaIteB06paTeHpeI.

PemOH

3.10 CMHa Ha kanaka Ha nomnTa

N3nCKBaHe:

YpeBbTe H3KnIOueHOT 3axpaHBAHeTo.
YpeBtE n3KNIOueH OT BOOCHa6nTENHa Mpeka.

3.10.1 CbajrHe Ha kanaka Ha nomnata

CbaTe BnHToBeTe Otnpei, KaTo 3aOnuHHeTe OToIy Harope (2,3).

1. CbaTe npednnaHn

3.11.2 MoNTIpaHHe Ha npEaHnnaHEn

MOnTnpaIeB06paTeH peI.

Poraneni padajicimi dily.

Zajistete Jednotlivé soucasti préd padem.

Sorg for at sikre apparater mod at glide.

Fare for nedfaldende dele pga. Iosnede skruer!

ersonskade pga. nedfaldende dele.

Sorg for at sikre componenten mod at falde ned.

Fare for nedfaldende dele pga. Iosnede skruer!

Sorg for at sikre componenten mod at falde ned.

Preindstilling:

1. Abn pumpens afdaekning.

1. Fjern pumpens afdaekning.

Sorg for at sikre apparater mod at glide

Loft apparentopifronten.

1. Fjern skruerne foreden (1).

1. Sænk apparatet ned.

Reparation

4.1.Fjernskruerne (1).

1. Skub toppladen bagud pa apparatet (2).
2. Bevag toppladen opad (3) for at fjerne den.

5.1.Fjernskruerne (1).

1. Frigor laseelementerne (2, 3).

1. Fjern betjeningspanelet.

7.

PASPAI

Fare for nefaldende delie pga. lnsnede skrurer! Personskade pga, nefaldende delie.

Sorg for at sikre componenten mod at falde ned.

Reparation

BEMARKI

Fare for nedfaldende dele pga. Isnnde skruer!

Sorg for at sikre componenten mod at falde ned.

Fjern skruerne pa fronten ved at starte nedefra og op (2, 3).

1. Fjern frontpanelet.

3.11.2 Montering af frontpanel

Repair hints - Washing machine

1 Concerning this document. 108

1.1 Important information 108

1.1.1 Purpose 108
1.2 Explanation of symbols 108
1.2.1 Danger levels.. 108
1.2.2 Hazard symbols 108
1.2.3 Structure of the warnings.. 109
1.2.4 General symbols 109

Tools and aids. 110

Repair 111

3.1 Replacing worktop 111

3.1.1 Removing worktop 111
3.1.2 Installing worktop 111

3.2 Replacing fascia panel 112

3.2.1 Removing fascia panel 112
3.2.2 Installing fascia panel 112

3.3 Replacing detergent drawer 113

3.3.1 Removing detergent drawer 113
3.3.2 Installing detergent drawer 113

3.4 Replacing detergent drawer handle 114

3.4.1 Removing detergent drawer handle 114
3.4.2 Installing detergent drawer handle 114

3.5 Replacing door 115

3.10 Replacing pump cover 124
3.10.1 Removing pump cover 124

3.10.2 Installing pump cover 124

3.11 Replacing front panel 125

3.11.1 Removing front panel 125
3.11.2 Installing front panel 127

Concerning this document

1.1 Important information

1.1.1 Purpose

These repair hints support consumer to repair appliances by himself according to the applicable eco-design regulation (as of 03/2021).

They contain information how to exchange defined spare parts including warnings and risks.

In case of questions, please contact our customer service. We will only be liable for damages if the repair hints have been followed properly.

1.2 Explanation of symbols

1.2.1 Danger levels

The warning levels consist of a symbol and a signal word. The signal word indicates the severity of the danger.

Table 1: Danger levels

Warning level Meaning
Danger	Non-observation of the warning message will result in death or serious injuries.
Warning	Non-observation of the warning message could result in death or serious injuries.
Caution	Non-observation of the warning message could result in minor injuries.
Notice	Non-observation of the warning message could result in damage to property.

1.2.2 Hazard symbols

Hazard symbols are symbolic representations which give an indication of the kind of danger.

The following hazard symbols are used in this document:

Hazard symbol Meaning
!	General warning message
	Danger from electrical voltage
	Risk of explosion
	Danger of cuts
	Danger of crushing

Concerning this document

Hazard symbol Meaning
	Danger from hot surfaces
	Danger from strong magnetic field
	Danger from non-ionizing radiation

Table 2: Hazard symbols

1.2.3 Structure of the warnings

Warnings in this document have a standardised appearance and a standardised structure.

Danger

Type and source of danger!

Possible consequences of ignoring the danger / warning.

Measures and prohibitions for preventing the danger.

The following example shows a warning that warns against electric shock due to live parts. The measure for avoiding the danger is mentioned.

Danger

Risk of electric shock due to live parts!

Death by electrocution

• Disconnect appliances from electrical supply at least 60 seconds before starting repairs.

1.2.4 General symbols

The following general symbols are used in this document:

Gen. symbol Meaning
1	Identification of a special tip (text and/or graphic)
i	Identification of a simple tip (only text)
	Identification of a link to a video tutorial

Gen. symbol Meaning
	Identification of required tools
	Identification of required preconditions
	Identification of a condition (if ..., then ...)
	Identification of a result
[Start]Identification of a key or button
[00123456] Identification of a material number
Status Identification of displayed text / window(in the appliance's display)

Table 3: General symbols

Tools and aids

Designation Details Images
Auxiliary tool [15000155]	Tool for loosening out of plastic parts
Screwdriver Torx T20 with bore hole [00340764]	100 mm, for screws with safety pin
Torque spanner [15000441]	Torque spanner 20 - 100 Nm
Slot screwdriver [00340854]	Blade 3.5 mm x 0.6 mm x 100 mm, Protective Insulation 1000 V AC
Slot screwdriver [00340855]	Blade 5.5 mm x 1.0 mm x 125 mm, Protective Insulation 1000 V AC
Needle-nose pliers, angled pattern [00341269]	Length 200 mm
Side-cutting pliers [00342182]	Length: 200 mm

Designation Details Images
Combination wrench [00340811]	Wrench size 10°mm, M6
Combination wrench [00340814]	Wrench size 13°mm, M8
Combination wrench [00340817]	Wrench size 17 mm, M10
Combination wrench [15000459]	Wrench size 16°mm, M10

Repair

3.1 Replacing worktop

Required tools:

Torx Bit TX20 with hole, long 6.3^ (1/4^) 152^ , for screws [00341272] with safety pin

Prerequisite:

Appliance is disconnected from power supply.
Appliance is disconnected from water supply.

3.1.1 Removing worktop

1. Remove screws (1).
2. Push worktop to the back of the appliance (2).
3. Move worktop upwards (3) to remove it.

3.1.2 Installing worktop

Install in reverse order.

Repair

3.2 Replacing fascia panel

Caution

Sharp housing edges!

Cut injuries

Wear protective gloves.

Warning

Slipping of tilted appliances!

Bone fractures / crush injuries

Secure appliances against slipping.

Caution

Risk of falling parts due to released screws!

Injury because of falling parts

Secure component from falling down.

Notice

Risk of falling parts due to released screws!

Damage to other parts of the appliance or at customers home e.g. bot

tom.

Secure component from falling down.

Prerequisite:

Appliance is disconnected from power supply.
Appliance is disconnected from water supply.
Worklop has been removed. Page 111
Detergent drawer has been removed. Page 113

3.2.1 Removing fascia panel

1. 1. Remove screws (1).

2. Release catch elements (2, 3).

1. Release plug contact of control unit.
2. Remove fascia panel.

3.2.2 Installing fascia panel

Install in reverse order.

Repair

3.3 Replacing detergent drawer

Prerequisite:

Appliance is disconnected from power supply.
Appliance is disconnected from water supply.

3.3.1 Removing detergent drawer

1. Pull out detergent drawer.
   2.1. Press down on insert (1)

2. Remove detergent drawer (2).

3.3.2 Installing detergent drawer

Install in reverse order.

Repair

3.4 Replacing detergent drawer handle

Prerequisite:

Appliance is disconnected from power supply.
Appliance is disconnected from water supply.
Detergent drawer has been removed. Page 113

3.4.1 Removing detergent drawer handle

1. Release catch elements.

1. Remove detergent drawer handle.

3.4.2 Installing detergent drawer handle

Install in reverse order.

Repair

3.5 Replacing door

Ca

Open hinge area!

Finger crushing / entrapment

Do not reach into the hinge area.
Wear protective gloves.

Prerequisite:

Appliance is disconnected from power supply.
Appliance is disconnected from water supply.
Door is opened.

3.5.1 Removing door

1.

Notice

Risk of falling parts due to released screws!

Damage to other parts of the appliance or at customers home e.g.

bottom

• Secure component from falling down.

Ca

Risk of falling parts due to released screws!

Injury because of falling parts.
- Secure component from falling down

Remove screws (1).

1. Remove door upwards.

Install in reverse order.

Repair

3.6 Replacing door components

Caution

Open hinge area!

Finger crushing / entrapment
Do not reach into the hinge area.
Wear protective gloves.

Prerequisite:

Appliance is disconnected from power supply.
Appliance is disconnected from water supply.
Door has been removed. Page 115

3.6.1 Removing door components

Disassemble door from outside to inside.

3.6.2 Installing door components

Install in reverse order.

Repair

3.7 Replacing door seal

Sharp housing edges!

Cut injuries

Wear protective gloves.

Risk of falling parts due to released screws!

Injury because of falling parts.

• Secure component from falling down.

Risk of falling parts due to released screws!

Damage to other parts of the appliance or at customers home e.g. bot

tom.

Secure component from falling down.

Prerequisite:

Appliance is disconnected from power supply.
Appliance is disconnected from water supply.
Detergent drawer has been removed. Page 113
Door has been removed. Page 115
Pump cover has been removed. Page 124

Slipping of tilted appliances!
Bone fractures / crush injuries
Secure appliances against slipping.

Lift up appliance at front.

1. Release screws at bottom of front panel (1).

1. Lower appliance down.

Repair

1. Remove screws in pump area (2). 5. 1. Release screws at back of appliance (1).

1. Remove worktop (2, 3).

Repair

6.1. Remove screws (1).

1. Release cat elements of fascia panel (2, 3).
2. Release screws of dispenser housing.

1. Remove fascia panel.

2. Remove drum light holder at top.

Notice

Risk of damaged surface! Surface of appliance can be scratched by using wrong tools. Only use plastic tools to replace the tension ring.

Remove tension ring from gasket with a plastic tool.

1. Release door seal from front panel.
2. Release cable connector from door lock.

Repair

1. Release screws on top of front panel (3).

1. Remove front panel.

2. Release all hose connections.

1. Remove door seal.

Risk of falling parts due to incorrect installation! Injury or damage to the appliance.

Tighten tension ring of boot gasket with 3,4 Nm.

Install in reverse order.

Repair

3.8 Replacing door lock

As a manufacturer, we are obliged to provide consumers with the spare part door lock including repair instructions in accordance with Regulation (EU) 2019/2023. However, we would like to point out that after replacing a door lock, an electrotechnical safety test by a qualified electrician is required before the device is put into operation. This person must be verifiably qualified according to the country-specific laws, regulations and standards.

Risk of electric shock due to live parts!

Danger to life through electric shock in case of improper repair

Electric parts should be repaired by a qualified electricians.
After the repair have a safety test according VDE 0701 or country-specific regulations performed.

Sharp housing edges!

Cut injuries

Wear protective gloves.

Slipping of tilted appliances!

Bone fractures / crush injuries

• Secure appliances against slipping.

Risk of falling parts due to released screws!

Injury because of falling parts.

• Secure component from falling down.

Risk of falling parts due to released screws!

Damage to other parts of the appliance or at customers home e.g. bottom.

• Secure component from falling down.

Prerequisite:

Appliance is disconnected from power supply.

Appliance is disconnected from water supply.

Appliances is freely accessible.
Worktop has been removed. Page 111
Fascia panel has been removed.
Door has been removed. Page 115
Tension ring has been removed.
Front panel has been removed.
Door seal has been removed.

1. Disconnect door lock plug.
2. Release door lock.

3. Remove door lock.

Repair

Install in reverse order.

Repair

3.9 Replacing drum light

Sharp housing edges!

Cut injuries

Wear protective gloves.

Slipping of tilted appliances!

Bone fractures / crush injuries

Secure appliances against slipping.

Risk of falling parts due to released screws!

Injury because of falling parts

Secure component from falling down.

Risk of falling parts due to released screws!

Damage to other parts of the appliance or at customers home e.g. bot

tom.

Secure component from falling down.

Prerequisite:

Appliance is disconnected from power supply.
Appliance is disconnected from water supply.
Appliances is freely accessible.
Worktop has been removed. Page 111
Detergent drawer has been removed. Page 113
Fascia panel has been removed.

3.9.1 Removing drum light

1. Pull drum light holder out of appliance.
2. Disconnect electrical connections.
3. Remove drum light from drum light holder.

3.9.2 Installing drum light

Install in reverse order.

Repair

3.10 Replacing pump cover

Prerequisite:

Appliance is disconnected from power supply.
Appliance is disconnected from water supply.

3.10.1 Removing pump cover

1. Open pump cover.

1. Remove pump cover.

3.10.2 Installing pump cover

Install in reverse order.

Repair

3.11 Replacing front panel

Prerequisite:

Appliance is disconnected from power supply.
Appliance is disconnected from water supply.
Detergent drawer has been removed. Page 113
Door has been removed. Page 115
Door seal has been removed.
Pump cover has been removed. Page 124

3.11.1 Removing front panel

1.

Lift up appliance at front.

1. Remove screws at bottom (1).

1. Lower appliance down.

Repair

4.1. Remove screws (1).

1. Push worktop to the back of the appliance (2).
2. Move worktop upwards (3) to remove it.

5.1. Remove screws (1).

1. Release catch elements (2, 3).

1. Remove fascia panel.

7.

Caution

Risk of falling parts due to released screws! Injury because of falling parts.

Secure component from falling down.

Repair

Notice

Risk of falling parts due to released screws! Damage to other parts of the appliance or at customers home e.g. bottom.

Remove screws at front beginning from bottom to top (2, 3).

1. Remove front panel.

3.11.2 Installing front panel

Install in reverse order.

Remonditeave - Pesumasin

1 Selle dokumendiga seoses 129

1.1 Tahtis teave 129
1.1.1 Eesmärk 129
1.2 Sumbolite selgitus 129
1.2.1 Ohutased 129
1.2.2 Ohusumbolid 129
1.2.3 Hoiatuste struktuur 130
1.2.4 Üldised sumbolid 130

Tooriistad ja abinoud. 131

Remont. 132

3.1 Toopinna yahetamine 132
3.1.1 Toopinna eemaldamine 132
3.1.2 Toopinna paigaldamine 132
3.2 Valispaneeli vahetamine 133
3.2.1 Valispaneeli eemaldamine 133
3.2.2 Valispaneeli paigaldamine 133

3.3 Pesuaine sahtli vahetamine 134

3.3.1 Pesuaine sahtli eemaldamine 134
3.3.2 Pesuaine sahtli paigaldamine 134

3.4 Pesuaine sahtli kaepideme vahetamine 135
3.4.1 Pesuaine sahtli kaepideme eemaldamine 135
3.4.2 Pesuaine sahtli kaepideme paigaldamine 135
3.5 Ukse vahetamine 136
3.5.1 Ukse eemaldamine 136
3.5.2 Ukse paigaldamine 136
3.6 Ukseosade vahetamine 137
3.6.1 Ukse osade eemaldamine 137
3.6.2 Ukse osade paigaldamine 137
3.7 Ukse tihendi vahetamine 138
3.7.1 Ukse tihendi eemaldamine 138
3.7.2 Uksetihendi paigaldamine 141
3.8 Ukseluku vahetamine 142
3.8.1 Ukseluku eemaldamine 142
3.8.2 Ukseluku paigaldamine 143
3.9 Trumli valgustuse vahetamine 144

3.9.1 Trumli valgustuse eemaldamine 144
3.9.2 Trumli valgustuse paigaldamine 144

3.10 Pumba katte vahetamine 145

3.10.1 Pumba katte eemaldamine 145
3.10.2 Pumba katte paigaldamine 145

3.11 Esipaneeli vahetamine 146

3.11.1 Esipaneeli eemaldamine 146
3.11.2 Esipaneeli paigaldamine 148

Selle dokumendiga seoses

1.1 Tahtis teave

1.1.1 Eesmark

Need remondinouanded toetavad tarbjat seadmete iseseisval remontimisel vastavalt kehtivale okodisaini märusele (03/2021).

Tabel 1: Ohutasedmed

1.2.2 Ohusumbolid

m = 311

1. Remova o painei frontal.

3.11.2 Instalar o painei frontal