PSS 65 C1 - Tool sharpening PARKSIDE - Free user manual and instructions

Product type	Electric sharpener
Brand	Parkside
Model	PSS 65 C1
Input voltage	220-240 V~, 50 Hz
Sharpening capacity - drill diameter	3-10 mm
Sharpening capacity - knife width	6-51 mm
Grinding wheel	Diamond, outer Ø 49.5 mm, bore 10.14 mm, thickness 7.9 mm
Max rotation speed	23,100 min⁻¹
Max peripheral speed	60 m/s
Sound pressure level (L_PA)	60.5 dB(A); K_PA = 3 dB
Sound power level (L_WA)	73.5 dB(A); K_WA = 3 dB
Duty cycle	S6 20% (10 min cycle) / S1 continuous
Protection class	II (double insulation)
Included sharpening attachments	For drills, knives/scissors, chisels/gouges
Warranty	3 years
Cleaning	Soft cloth, no solvents
Spare parts available	Yes, references in manual

Frequently Asked Questions - PSS 65 C1 PARKSIDE

How to sharpen a drill with the PSS 65 C1?

To sharpen a drill, mount the drill sharpening attachment. Insert the drill into the drill holder, position it in the V-slot until the metal stop, then secure it. Place the holder in the pivoting drill holder and sharpen by moving the holder back and forth on the grinding wheel. Repeat for the other side.

How to change the grinding wheel?

Unplug the device. Unscrew the grinding wheel nut (left-hand thread) counterclockwise. Replace the wheel. Hand-tighten the nut. Perform a trial run without load for at least 60 seconds.

Can I sharpen scissors with wavy blades?

No, the device cannot sharpen scissors with wavy or serrated blades. Use the knife and scissors attachment only for straight blades.

What are the important safety instructions?

Wear safety goggles. Unplug before any adjustments. Never use the device without a protective guard. Keep hands away from the running wheel. Use hearing protection. Do not operate when tired.

How to use the knife attachment?

Mount the knife and scissors attachment. Turn on the device. Insert the blade completely into the sharpening groove. Guide it with light pressure on the wheel and slowly pull it towards you. Repeat on the other side.

Why does the device not start?

Check the mains voltage and fuses. Inspect the plug and cord. If the switch is defective, have it repaired by customer service. A motor defect also requires professional repair.

How to clean and maintain the sharpener?

Unplug the device. Clean the surface with a soft cloth or brush. Never use cleaners or solvents. Check the condition of the grinding wheel before each use. Store the device in a dry place out of reach of children.

What accessories are included?

The delivery includes: the device, the knife and scissors sharpening attachment, the drill attachment, the chisel and gouge attachment, a spare grinding wheel, and the user manual.

What is the warranty period?

This product comes with a 3-year warranty from the date of purchase. Keep the receipt as proof. The warranty covers material and manufacturing defects. Wear parts (grinding wheel) are warranted for 2 years.

Can I sharpen saw blades?

No, the device is not designed for sharpening saw blades. Only use the indicated tools: drills, knives, scissors, chisels, and gouges. Use of saw blades is prohibited for safety reasons.

USER MANUAL PSS 65 C1 PARKSIDE

Tool Sharpening Station

Translation of the original instructions

NL BE

Slipstation

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

FR BE

GB/IE Translation of the original instructions Page

General description. 21

Scope of delivery. 21

Function description. 21

Summary 21

Technical specifications. 21

Safety Instructions. 22

Symbols and icons 22

General Safety Directions for Power Tools 22

Further Safety Instructions 24

Residual risks. 25

Assembly 26

Setting up 26

Mount the sharpener 26

Operation 26

Switching on and off 26

Sharpening drills. 27

Sharpening picks and chisels. 27

Sharpening knives. 28

Sharpening scissors 28

Changing the grinding wheel 28

Cleaning and maintenance. 29

Cleaning. 29

Storage 29

Waste disposal and environmental protection .29

Replacement parts/accessories...30

Trouble Shooting 31

Guarantee 32

Repair Service. 33

Service-Center 33

Importer 33

Translation of the original

EC declaration of conformity ....139

Exploded Drawing 147

Introduction

Congratulations on the purchase of your new device. With it, you have chosen a high quality product.

During production, this equipment has been checked for quality and subjected to a final inspection.

The operating instructions constitute part of this product. They contain important information on safety, use and disposal.

Before using the product, familiarise yourself with all of the operating and safety instructions. Use the product only as described and for the applications specified.

Keep this manual safely and in the event that the product is passed on, hand over all documents to the third party.

Intended use

The sharpening station is suitable for sharpening tools (e.g. drills, knives, scissors, picks, chisel).

The device is not intended for all other types of applications (e.g. grinding with unsuitable grinding tools, grinding with a coolant solution, grinding hazardous materials such as asbestos).

The equipment is intended for use in the field of DIY. It is not designed for commercial use.

The equipment is designed for use by adults. Young people over the age of 16 are permitted to use the equipment only under supervision.

The manufacturer shall not be liable for damages caused by use other than for the intended purpose or by incorrect operation.

General description

The illustrations can be found on the front and rear fold-out pages.

Scope of delivery

Unpack the equipment and check that it is complete. Dispose of the packaging material correctly.

• Appliance
• Sharpener for knives and scissors
• Sharpener for drills
• Sharpener for picks and chisels
• Spare grinding wheel
• Instruction Manual

Function description

The sharpening station is suitable for sharpening tools (e.g. drills, knives, scissors, picks, chisels). The scope of delivery contains three sharpeners for this purpose, which, as a guide and safety device, enable precise sharpening and grinding. Refer to the following descriptions for a functional description of the controls.

Summary

1 Mains plug

2 Sharpener for knives and scissors
3 On/off switch

4 Spacer

5 Magnet holder
6 Tool table
7 Retaining screw for angular adjustment
8 Protective hood
9 Mounting holes for work bench assembly
10 Grinding wheel
11 rotatable drill mount

12 Knurled nut for drill-fastening
13 Release lever for sharpener
14 Drill holder
15 Adjusting device
16 Grinding wheel nuts

Technical specifications

Tool sharpening station...PSS 65 C1

Nominal

input voltage 220 - 240 V~, 50 Hz

Power consumption P.....65 W (S6 20%)*

Power consumption P. 25 W (S1)

Measurement idling speed n_0 6700min^1

Safety class

Protection category.. IP X0

Weight

(incl. accessories) approx. 1.37 kg

Grinding angle range. 15^ - 50^

Sharpness drill diameter. 3 -10 mm

Sharpness knife width.. 6-51 mm

Grinding wheel

Outer diameter 49.5 mm

Borehole diameter. 10.14 mm

Thickness 7.9 mm

Abrasive Diamond

Base body.. Metal

Working speed max. 60m / s

Rotational speed ..... max. 23100 min

Sound pressure level

(L_pA) 60.5 dB(A); K_pA = 3 dB

Sound power level

( LWA) 73.5 dB(A); KW2 = 3 dB

• Operating mode S6 20%: Continuous operation with intermittent load (cycle time 10 min). In order not to heat the motor more than permitted, the motor may only be operated for 20% of the cycle time with the stated nominal power and must then continue running for 80% of the cycle time without a load.

** Operating mode S1: Continuous operation with constant load

GBIE

Noise and vibration values have been determined according to the standards and regulations mentioned in the declaration of conformity.

Safety Instructions

Symbols and icons

Symbols on the device:

Warning!

Read the instruction manual.

Wear ear protection.

Risk of electric shock! Disconnect from the mains before carrying out maintenance and repair work.

Safety class II (Double insulation)

Do not dispose of electrical equipment in household waste.

Drill diameter

Grinding wheel nut

Grinding angle Workpiece size

For grinding knives and scissors

Rotatable drill retainer

Symbols in the manual:

Warning symbols with information on damage and injury prevention.

Instruction symbols with information on preventing damage.

Connect the machine to the power supply.

Pull out the mains plug.

Wear ear protection

Help symbols with information on improving tool handling.

General Safety Directions for Power Tools

WARNING! Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool).

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operation of the power tool in a damp environment is unavoidable, please use a residual current circuitry. The use of a residual current circuitry reduces the risk of an electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention white operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction

GB E

and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect

the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5) Service
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Further Safety Instructions

• Connect the device only to a power point with a RCD (Residual Current Device) with a measured residual current of not more than 30mA .
• Keep the mains cable and extension cable away from the grinding disk and saw chain. In the event that it is damaged or severed, immediately disconnect the plug from the socket.

Do not touch the cable before it has been disconnected from the mains. Risk of electric shock.

The replacement of the plug or the cable must be carried out by the manufacturer or his/her customer service in order to avoid any hazards.

Only switch the device on once it is safely fixed to the worktop.

• For your own safety only use accessories and attachments which were stated in the operating instructions or recommended or specified by the tool manufacturer.

• Only use grinding wheels where the printed rotational speed is at least as high as what has been specified on the name plate of the device.

• Carry out a visual inspection of the grinding wheel before use. Do not use any damaged or deformed grinding wheels. Replace any damaged or worn grinding wheels.

• Make sure that the sparks produced by grinding do not present a danger, e.g. reach people or ignite flammable substances.

• Never keep the fingers between the grinding wheel and spark protection or in close proximity to the protective hoods. There is a risk of crushing.

• The rotating parts of the device cannot be covered due to functional reasons. Therefore, proceed cautiously and hold the workpiece firmly in order to avoid slipping which could cause your hands to come into contact with the grinding belt or grinding wheel.

• The workpiece gets hot during grinding. Do not touch the machined area, allow it to cool down. There is a risk of burning. Do not use coolants or the like.

If you are tired or have consumed alcohol or tablets, do not work with the device. Always have a break on time

• Switch the device off and remove the mains plug

• to loosen a blocked insertion tool,

• if the connection line is damaged or entangled,

• in case of unusual sounds.

Residual risks

Even if properly operating and handling this electric tool, some residual risks will remain. Due to its construction and build, this electric tool may present the following hazards:

a) Lung damage, if suitable respiratory protection is not worn.

b) Hearing damage, if suitable ear protection is not worn.

c) Damages to health due to

touching the area of the grinding tool which was not covered:

• the ejection of pieces from workpiece or damaged grinding wheels.

d) Damage to your health caused by swinging your hands and arms when operating the appliance for longer periods of time or if the unit is not held or maintained properly.

Warning! During operation, this electric tool generates an electromagnetic field which, under certain circumstances, may impair the functionality of active or passive medical implants. To reduce the risk of serious or lethal injuries, we recommend that persons with medical implants consult their doctor and the manufacturer of their medical implant before operating the machine.

Assembly

Caution! Risk of injury!

that you have sufficient space in which to work, and that you do not endanger other people.

• All covers and protective devices must be assembled properly before commissioning.
• Disconnect the mains plug before changing the setting on the device.

Setting up

Place the sharpening station on firm surface and fasten the device. Ideally, bolt the drill to the surface. Use the mounting holes for the work bench assembly (A 9) in the baseplate for this.

The screws and nuts required for assembly are not part of the scope of delivery.

Mount the sharpener

1. Select one of the three sharpeners.
2. In order to remove a sharpener from the working position, you must press down the release lever for the sharpener (A 13).
3. Remove the sharpener from the guide rails, upwards.
4. In the storage positions, the sharpeners are not fixed to the right and left side and can be easily removed from the guide rails.
5. In order to fasten the selected sharpener in the working position, from above push this into the guide rails. Press the sharpener down until it snaps into place.

The sharpeners also present a safety device. Never use this device without a sharpener. Risk of injury!

Operation

Caution! Risk of injury!

• Always disconnect the plug from the mains socket before working.

• Use only grinding disks and accessories recommended by the manufacturer. The use of other insertion tools and other accessories may cause risk of injury.

• Never operate the device without the visual protection disk.

• Switch on the equipment only when it is safely installed on the work surface.

Despite spark protection, always wear safety goggles while working in order to avoid eye injuries.

We recommend wearing ear protection to prevent damage to hearing.

Keep your hands away from the grinding wheel and grinding belt when the device is in operation. Injury hazard.

Switching on and off

Ensure that the mains voltage matches the specifications on the rating plate.

Connect the equipment to themains.

1. To switch on, press the "I" On switch and the device starts up (see 3).
2. To switch off, press the "0" off switch and the device switches off (see A 3).

After switching on the device, wait until the device has reached its max. speed. Only then must you start with the grinding.

The disk will continue to run after the equipment is switched off. There is a risk of injury.

Test run:

Before starting work and after each change of grinding disk, carry out a test run of at least 60 seconds with no load. Switch off the equipment immediately if the disk runs lumpy, substantial vibrations occur, or abnormal noises are generated.

Sharpening drills

Drills with a diameter of 3 - 10mm can be sharpened.

1. Mount the selected sharpener (see Mounting sharpener).
2. Remove the drill holder (14) from the sharpener.
3. Insert the drill into the drill holder (14). Do not attach the drill.
4. Insert the drill holder (14) upwards into the adjusting device (15) using the knurled nut for drill-fastening (12).

5. Push the drill to the front into the V-nut up to the metal stop. The cutting edges of the drill must fit closely to the metal surfaces.

6. Using the knurled nut fasten the drill for drill-fastening (12).

7. Remove the drill holder (14) and insert this into the rotatable drill mount (11) from below using the knurled nut for drill-fastening (12).
8. Check the alignment of the drill. The cutting edges of the drill must be touching the grinding wheel (10).
9. Switch the device on and grind the drill by moving the rotatable drill mount (11) to and fro in the direction of the arrow.
10. Switch the device off and wait for the grinding wheel (10) to stop.
11. Remove the drill holder (14) and insert it into the rotatable drill mount (11) by rotating in by 180^ . Using the same adjustment, you can grind the opposite cutting edge of the drill.
12. Switch the device off and grind the drill.
13. Switch the device off and wait for the grinding wheel (10) to stop.

Sharpening picks and chisels

1. Mount the selected sharpener (see Mounting sharpener).
2. Place the blade on the tool table (6) so that it lies against the spacer (4). The magnetic holder (5) keeps the blade in position.
3. Release the retaining screw for the angular adjustment (7) and turn the tool table (6) into position. Select the angle according to the existing bevel angle (angle of the bevelled edge).
4. Tighten the retaining screw for angular adjustment (7) again.

GB E

1. Switch the device on and move the tool table (6) equally back and forth along the grinding wheel (10).
2. Always use light pressure while sharpening and slowly push the blade towards the grinding wheel (10).
3. Repeat the sharpening process until all irregularities have been removed.
4. Switch the device off and wait for the grinding wheel (10) to stop.

To sharpen a chisel, turn the chisel over and repeat the process from Point 5.

Sharpening knives

The device is not suitable for grinding serrated knives.

1. Mount the selected sharpener (see Mounting sharpener).
2. Turn the machine on.
3. Insert the blade of the knife right into the grinding slot.
4. Using light pressing guide the blade along the grinding wheel (10) and evenly and slowly pull the knife towards you.
5. Turn the knife and insert the knife blade into the opposite grinding slot.
6. Repeat this grinding process for this side of the blade as well.
7. Execute the alternating grinding process until the cutting edge is burr-free and sharp.
8. Switch the device off and wait for the grinding wheel (10) to stop.

Sharpening scissors

The device is not suitable for grinding serrated scissors. The device is not suitable for grinding pinking shears.

1. Mount the selected sharpener (2)(see Mounting sharpener).
2. Completely open the scissors.
3. Turn the machine on.
4. Insert one of the scissor blades into the grinding slot.
5. Using light pressure guide the blade from the screw up to the tip along the grinding wheel (10).
6. Remove the scissors from the sharpening station and turn the scissors to sharpen the other blade.
7. Insert the other scissor blade into the grinding slot.
8. Using light pressure guide the blade from the screw up to the tip along the grinding wheel (10).
9. Execute the alternating grinding process until the cutting edges are burr-free and sharp.
10. Switch the device off and wait for the grinding wheel (10) to stop.

Changing the grinding wheel

Information on replacement:

• Never operate the device without protective equipment.
• Ensure that the grinding wheel dimensions match those of the device.
• Never use separate bushings or adapters in order to make grind

ing wheels whose hole is too large fit the device.

• Do not use any saw blades.
  Always reassemble the device completely after replacing the grinding wheel.

Switch the device off and remove the mains plug.
Allow the device to cool down.

When the grinding disc nut (16) is being tightened or loosened, the grinding disc (10) must be held firmly by hand or the axle held firmly in place with a pair of pliers.

1. Release the grinding wheel nut (16) in the clockwise direction (left-handed thread).

1. Remove the grinding wheel (10).
2. Set up a new grinding wheel (10). Screw the grinding wheel nut (16) in the anti-clockwise direction (left-handed thread).
3. Test run: Before starting work and after each change of grinding disk, carry out a test run of at least 60 seconds with no load. Switch off the equipment immediately if the disk runs lumpy, substantial vibrations occur, or abnormal noises are generated.

Cleaning and maintenance

Disconnect the plug before adjustment, maintenance or repair.

Have any work not described in these instructions carried out by a specialist workshop. Use only original compo

nents. Allow the equipment to cool before carrying out any maintenance and cleaning work. There is a risk of burns.

Before each use, check the equipment for obvious defects such as loose, worn or damaged components and check that screws or other parts are sitting correctly. In particular, check the grinding disk (A 10). Replace damaged parts.

Cleaning

Do not use cleaning agents or solvents. Chemical substances may attack plastic parts of the equipment. Never clean the equipment under running water.

• Clean the equipment thoroughly after each use.
• Clean the surface of the device with a soft brush or cloth.

Storage

• Store the appliance in a dry place well out of reach of children.
  Grinding disks must be stored dry and upright and are not to be stacked.

Waste disposal and environmental protection

Be environmentally friendly. Return the tool, accessories and packaging to a recycling centre when you have finished with them.

Machines are not to be place with domestic waste.

GB E

• Hand over the device at an utilization location. The plastic and metal parts employed can be separated out into pure materials and recycling can be implemented. Ask your Service Center about this.
  Defective units returned to us will be disposed of for free.

Replacement parts/accessories

Spare parts and accessories can be obtained at www.grizzlytools.shop

If you have issues ordering, please use the contact form. If you have any other questions, contact the "Service-Center" (see page 33).

Position Instruction manual	Position Exploded drawing	Description number	O
A 10	19+21 Grinding wheel with Grinding wheel nuts	91103590
A 2	25 Sharpener for knives and scissors	91103591
12 Sharpener for drills		91103592
10		Sharpener for picks and chisels	91103593

Trouble Shooting

Always disconnect the plug from the mains socket before working.

Danger of electric shock.

Problem Possible Cause	Use Error correction
Device doesn’t start	Mains voltage missingMain circuit breaker is tripped	Check the socket, mains cable, line, mains plug, repairs to be carried out by qualified electrician if necessary, check main circuit breaker.
	On/off switch (A3) may be defective	Repair by Customer Care
	Engine faulty
Grinding tools do not move although the engine is running	Grinding wheel nut (A16) loose	Tighten grinding wheel nut (see „Changing the grinding wheel“)
	Workpiece, remaining workpieces or remaining grinding tools block drive	Remove blockages
Engine is slower and stops	Device is overloaded through workpiece	Reduce pressure on grinding tool
		Workpiece unsuitable
Grinding wheel does not rotate smoothly, abnormal noises can be heard	Grinding wheel nut (A16) loose	Tighten grinding wheel nut (see „Changing the grinding wheel“)
	Grinding wheel (A10) faulty	Change grinding wheel

Guarantee

Dear Customer,

This equipment is provided with a 3-year guarantee from the date of purchase. In case of defects, you have statutory rights against the seller of the product. These statutory rights are not restricted by our guarantee presented below.

Terms of Guarantee

The term of the guarantee begins on the date of purchase. Please retain the original receipt. This document is required as proof of purchase.

If a material or manufacturing defect occurs within three years of the date of purchase of this product, we will repair or replace - at our choice - the product for you free of charge. This guarantee requires the defective equipment and proof of purchase to be presented within the three-year period with a brief written description of what constitutes the defect and when it occurred.

If the defect is covered by our guarantee, you will receive either the repaired product or a new product. No new guarantee period begins on repair or replacement of the product.

Guarantee Period and Statutory Claims for Defects

The guarantee period is not extended by the guarantee service. This also applies for replaced or repaired parts. Any damages and defects already present at the time of purchase must be reported immediately after unpacking. Repairs arising after expiry of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully produced in accordance with strict quality guidelines and conscientiously checked prior to delivery.

The guarantee applies for all material and manufacturing defects. This guarantee does not extend to cover product parts that are subject to normal wear and may therefore be considered as wearing parts (e.g. grinding wheels) or to cover damage to breakable parts (e.g. switches).

This guarantee shall be invalid if the product has been damaged, used incorrectly or not maintained. Precise adherence to all of the instructions specified in the operating manual is required for proper use of the product. Intended uses and actions against which the operating manual advises or warns must be categorically avoided.

The product is designed only for private and not commercial use. The guarantee will be invalidated in case of misuse or improper handling, use of force, or interventions not undertaken by our authorised service branch.

Processing in Case of Guarantee

To ensure quick handling of you issue, please follow the following directions:

• Please have the receipt and item number (IAN 374688_2104) ready as proof of purchase for all enquiries.
• Please find the item number on the rating plate.

• Should functional errors or other defects occur, please initially contact the service department specified below by telephone or by e-mail. You will then receive further information on the processing of your complaint.

• After consultation with our customer service, a product recorded as defective can be sent postage paid to the service address communicated to you, with the proof of purchase (receipt) and specification of what constitutes the defect and when it occurred. In order to avoid acceptance problems and additional costs, please be sure to use only the address communicated to you. Ensure that the consignment is not sent carriage forward or by bulky goods, express or other special freight. Please send the equipment inc. all accessories supplied at the time of purchase and ensure adequate, safe transport packaging.

Repair Service

For a charge, repairs not covered by the guarantee can be carried out by our service branch, which will be happy to issue a cost estimate for you. We can handle only equipment that has been sent with adequate packaging and postage.

Attention: Please send your equipment to our service branch in clean condition and with an indication of the defect.

Equipment sent carriage forward or by bulky goods, express or other special freight will not be accepted.

We will dispose of your defective devices free of charge when you send them to us.

Service-Center

GB Service Great Britain Tel.:[phone]

E-Mail: [e-mail]

IAN 374688_2104

IE Service Ireland

fei.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (off peak))

E-Mail: [e-mail]

IAN 374688_2104

Importer

Please note that the following address is not a service address. Please initially contact the service centre specified above.

Garantie - France. 46

Puisance absorbee.65 W (S6 20* Puisance absorbee.25 W (S1)**

Vitesse nominale _0 6700 min1 Classe de protection

Type de protection.. IP X0

Poids (y compris accessoires).env. 1,37 kg
Plage d'angle d'abrasion ..... 15° - 50°

Chere cliente, cher client,

Slipstation...PSS 65 B1

Nominale

ingangsspanning .... 220 - 240 V~, 50 Hz

Krachtontneming 65 W (S6 20%)*

Krachtontneming 25 W (S1)**

Prikon P 65 W (S6 20%)*

Prikon P. 25 W (S1)**

Prikon P 65 W (S6 20%)*

Prikon P_0 25 W (S1)**

Slibning of knife 117

Slibestation...PSS 65 C1

Nominal spaending..220 - 240 V\~, 50 Hz

Effektforbrug P .65 W (S6 20%)*

Effektforbrug P. 25 W (S1)

Beregnet tomgangsomdrejningstal

n. 6700 min-1

Kapslingsklasse.

Characteristicas techniques

Afiladora . PSS 65 C1

Tensión entrada

nominal 220 - 240 V\~, 50 Hz

Consumo de potencia P.65 W (S6 20%)*

Consumo de potencia P_0 25 W (S1)**

Translation of the original EC declaration of conformity

We hereby confirm that the

Tool sharpening station

model PSS 65 C1

Serial number 000001 - 493534

conforms with the following applicable relevant version of the EU guidelines:

2006/42/EC · 2014/30/EU · 2011/65/EU* & (EU)2015/863

In order to guarantee consistency, the following harmonised standards as well as national standards and stipulations have been applied:

EN 62841-1:2015 • EN ISO 12100:2010 • EN 13236:2019 EN 55014-1:2017/A11:2020 • EN 55014-2:2015 EN IEC 61000-3-2:2019 • EN 61000-3-3:2013/A1:2019 • EN IEC 63000:2018

This declaration of conformity is issued under the sole responsibility of the manufacturer:

Documentation Representative

• The object of the declaration described above satisfies the provisions of Directive 2011/65/EU of the European Parliament and the Council of 8 June 2011 on limiting the use of certain harmful substances in electrical and electronic appliances.