IB 740 Adv - Effect machine Kärcher - Free user manual and instructions

Product Type	Dry Ice Blast Cleaner
Brand	Kärcher
Model	IB 7/40 Advanced (IB 740 Adv)
Power Supply	220-240 V, 1~, 50 Hz, 0.6 kW
Residual Current Circuit Breaker (RCCB)	30 mA, type B
Compressed air supply pressure (min/max)	0.2 MPa (2 bar) / 1.0 MPa (10 bar)
Compressed air consumption	0.5 to 3.5 m³/min
Jet pressure (max.)	1.0 MPa (10 bar)
Dry ice pellet diameter (max.)	3 mm
Dry ice consumption	15 to 50 kg/h
Dry ice hopper capacity	15 kg
Dimensions (L × W × H)	510 × 768 × 1096 mm
Weight ready for use (Advanced)	95 kg
Empty weight without accessories	71 kg
Max. gun recoil force	30 N
Sound pressure level (depending on nozzle)	Up to approx. 100 dB(A)
Safety devices	Emergency stop, safety button, automatic shut-off
Required protective equipment	Safety glasses, cold-proof gloves, hearing protection, long clothing
Maintenance	Condensate drain, water separator filter replacement, hose inspection every 2 years
Warranty	According to distributor conditions
Included accessories	Long flat jet nozzle, spray gun, hose

Frequently Asked Questions - IB 740 Adv Kärcher

What type of dry ice to use?

Use only dry ice pellets (solid carbon dioxide) with a maximum diameter of 3 mm. Using other abrasives would damage the device and void the warranty.

How to avoid risks related to carbon dioxide (CO₂)?

Ensure adequate ventilation of the work area. CO₂ is heavier than air and can accumulate in confined spaces. Monitor symptoms (headache, nausea) and use a personal detector if necessary. Stop the device immediately if signs of intoxication appear.

What protective equipment to wear?

Wear well-fitting safety glasses, insulated gloves (EN 511), hearing protection and long-sleeved clothing. Never touch dry ice without protection (temperature of -79 °C).

How to fill the dry ice hopper?

Open the lid, check for foreign objects or water, then pour in the pellets. Close tightly. Wear protective gloves to avoid cold burns.

Why is the dry ice jet not coming out?

Check that the compressed air supply is sufficient (min. 0.2 MPa), that the jet pressure is set correctly, that the hopper is not empty and that the dry ice metering is activated (button on the gun). Refer to the fault table in the manual.

How to empty the dry ice hopper?

Place a container under the drain outlet, then press the 'Empty dry ice hopper' button on the control panel. The draining stops automatically after the set time (adjustable in the settings).

What is the recommended maintenance frequency?

Daily: inspect the hose and cables. Every 100 hours: check couplings and metering. Every 500 hours or annually: have the device checked by customer service. Every 2 years: replace the jet hose.

How to adjust the jet pressure and dry ice metering?

Use the +/- keys on the control panel (or directly on the gun for the Advanced version). Higher pressure gives more aggressive cleaning. The metering is adjustable from 15 to 50 kg/h. Adapt according to the soiling and surface.

What to do in case of emergency stop?

Release the gun trigger and press the emergency stop button. Shut off the compressed air supply. To restart, unlock the emergency stop by turning the button, then reactivate the air and the device.

How to transport the device safely?

Before transport, completely empty the dry ice hopper and purge the compressed air. Lock the brakes and secure the device with straps in the vehicle. Respect the weight (95 kg) to avoid injuries.

USER MANUAL IB 740 Adv Kärcher

Professional KARCHER Gas 7/40 industrial pressure testing machine with visible control panel and hose (no text or symbols on device body)

Deutsch 3

English 13

Français 23

Italiano 34

Nederlands 45

Español 55

Português 66

Dansk 77

Norsk 87

Svenska 97

Suomi 107

Ελληνικά 117

Türkçe 128

Русский 138

Magyar 149

Čeština 159

Slovenščina 169

Polski 179

Românește 190

Slovenčina 201

Hrvatski 211

Srpski 221

Български 231

Eesti 242

Latviešu 252

Lietuviškai 262

Українська 272

中文 283

العربية 305

⚠Gefahr

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Handgriff (Zubehör)

Line drawing of a mechanical bolt with a flanged cap (no text or symbols)

Technical line drawing of a mechanical pulley or wheel assembly (no text or symbols)

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent owners.

Contents

Environmental protection .. EN .. 1

Safety instructions ..... EN .. 1

Proper use ..... EN .. 2

Function ..... EN .. 2

Control elements..... EN .. 2

Start up.... EN .. 3

Operation ..... EN .. 4

Shutting down..... EN .. 6

Transport..... EN .. 6

Storage ..... EN .. 6

Maintenance and care .... EN .. 6

Troubleshooting ..... EN .. 7

Technical specifications ... EN .. 9

Accessories ..... EN . 10

Warranty ..... EN . 10

EU Declaration of Conformity EN . 10

Declaration of Conformity .. EN . 10

Environmental protection

	The packaging material can be recycled. Please do not place the packaging into the ordinary refuse for disposal, but arrange for the proper recycling.
	Old appliances contain valuable materials that can be recycled. Please arrange for the proper recycling of old appliances. Batteries, oil, and similar substances must not enter the environment. Please dispose of your old appliances using appropriate collection systems.

Notes about the ingredients (REACH)

You will find current information about the ingredients at:

www.kaercher.com/REACH

Safety instructions

The appliance may only be operated by persons who have read and understood the contents of this operating instructions manual. Please ensure that you conform to all the safety instructions and regulations.

→ This operating instructions manual must be stored in such a way that it can be easily accessed by the operator.

Danger or hazard levels

⚠️Danger

Immediate danger that can cause severe injury or even death.

⚠ Warning

Possible hazardous situation that could lead to severe injury or even death.

Caution

Possible hazardous situation that could lead to mild injury to persons or damage to property.

Symbols on the machine

Pure graphical symbols representing surveillance, human figures, a dog, and devices without any text or labels

⚠️Danger

Risk of injury on account of flying dry ice pellets. Do not direct the jet pistol on persons. Keep third persons away from the place of use and when the machine is being operated (by cording off the area). Do not touch/hold the nozzle or the dry ice jet when the machine is running.

⚠️Danger

Risk of suffocation on account of carbon dioxide. The dry ice pellets are made of solidified carbon dioxide. The carbon dioxide content in the air at the place where the machine is used will increase when the machine is running. Ensure adequate ventilation at the place of use; if possible, use an alarm to warn persons. Symptoms of high levels of carbon dioxide in the air that is breathed in:

• 3...5%: headache, faster breathing.
• 7...10%: headache, nausea and perhaps even unconsciousness.

If any of these symptoms occur, please switch off the machine immediately and get a breath of fresh air; improve the ventilation before starting work again with the machine or use respirators.

Carbon dioxide is heavier than air and it accumulates in narrow spaces, rooms on lower levels or in closed containers.

Make sure that the work area is ventilated sufficiently.

Follow the safety specifications of the manufacturer of dry ice.

⚠Danger

Risk of injury on account of electro-static discharge; risk of damage to the electronic components. The object being cleaned can get charged electrically during the cleaning process. Provide suitable earthing for the object being cleaned and ensure that the earthing remains intact during the entire cleaning process.

⚠️DANGER

Risk of injury on account of electric shock. Pull the plug out of the socket before opening the control cabinet.

DANGER

Risk of cold burns. Dry ice has a temperature of -79 °C. Never touch dry ice or cold parts of the machine without appropriate protection.

⚠️Danger

Risk of injury on account of flying dry ice pellets or dirt particles. Wear close fitting safety goggles.

Risk of hearing impairment. Wear ear-protection aids.

⚠️Danger

Risk of injury on account of flying dry ice pellets or dirt particles.

Wear protective gloves and long-sleeved protective overalls as per EN 511.

DANGER

Risk of injury on account of electric shock. Pull the plug out of the socket before opening the control cabinet.

General notes on safety

⚠️DANGER

Risk of injury if the machine is left running in an unattended state. Disconnect the mains plug from the socket before performing any work.

⚠️Danger

Risk of cold burns on account of dry ice or cold parts of the machine. While working on the machine, wear appropriate safety gear for protection against cold or remove dry ice and let the machine heat up. Never put dry ice in your mouth.

⚠ Warning

Risk of injury on account of the recoil force of the jet pistol. Ensure that you are standing at a safe place and hold the jet pistol properly in your hand before pressing the trigger of the jet pistol.

⚠ Danger

Risk of injury on account of flying objects. Fix light cleaning objects properly to prevent them from being dragged off with the dry ice jet.

⚠ Warning

Do not use the appliance when there are other persons around unless they are also wearing safety equipment.

The appliance must not be used if a connecting line or important parts of the appliance, e.g. safety devices, spray hose, spray gun.

Danger of crushing on account of the dosing equipment. Always remove the machine plug from the socket before removing the protective shield of the dry ice container.

Specifications and Guidelines

For the operation of this system the following regulations and directives are applicable in the Federal Republic of Germany (available from Carl Heymanns Verlag KG, Luxemburger Straße 449, 50939 Cologne):

• BGV D 26 Spray jet tasks
• Executing instructions for BGV D 26
  – BGR 117 Working in closed rooms
• BGR 189 Using safety gear
  – BGR 195 Using of safety gloves
• BGR 500 Working with spraying devices
  – BGI 534 Working in closed rooms
• BGI 836 Gas warner

Safety Devices

Emergency-stop button

If the emergency stop button is pressed, the dry ice dosing is stopped and the air flow from the nozzle is interrupted.

Switch-off in case of emergency

→ Release the trigger of the jet pistol.
→ Press emergency-stop button.

The dry ice dosing is stopped and the air flow from the nozzle is interrupted.

→ Interrupt the compressed air supply.

Proper use

The machine is used to remove dirt using dry ice pellets that are speeded up using an air jet.

The machine should not be operated in explosive environments.

Use only dry ice pellets as jet medium. Using any other jet medium can cause damage to the machine.

Function

The air pressure reaches the jet pistol via a pressure regulation valve. The valve opens when the trigger of the jet pistol is pressed and the air flow comes out from the jet pistol. Additionally, dry ice pellets are dosaged into the air stream via the dosing device.

With the version "IB 7/40 Advanced" the additional dosing can be switched off at the jet pistol. The dry ice pellets hit the surface to be cleaned and remove the dirt. Additional heat currents are formed between the dirt and the object to be cleaned by the -79 °C cold dry ice pellets; this results in the dirt being loosened. At the same time, dry ice immediately gets coverted into gaseous carbon dioxide on contact and requires 700 times the volume of dry ice. Thus, the dirt penetrated by the dry ice thus gets thrown off.

During the spraying operation through the jet, a vibrator located on the dry ice container ensures continuous sliding of the dry ice pellets.

Control elements

Device

1 Push handle
2 Cover of the dry ice container
3 Holder for jet pistol
4 Storage compartment for accessories
5 Operating field
6 Coupling of the control cable
7 Earthing rope with clamp (only IB 7/40 Advanced, option for IB 7/40 Classic)
8 Coupling spray agent hose
9 Guiding roll with fixed position brake
10 Transport handle, bumper at the rear
11 Dry ice outlet for emptying the container

1 Cable clamp
2 Mains cable with mains plug
3 Pressure relief valve, condensate draining of the water separator
4 Compressed air connection
5 Condensate drain-out
6 Fuse F1, below the side panel

Operating field

1 Statistics key, reset counter
2 Key to empty the dry ice container
3 Display
4 Key "increase jet pressure"
5 Key "decrease jet pressure"
6 Increase the dry ice dosing
7 Decrease the dry ice dosing
8 Power switch
9 Emergency-stop button
10 Key switch

Display

1 Indicator lamp - control voltage green: Control voltage OK red: Control voltage too low yellow: Emptying of dry ice container active
2 Indicator lamp emergency STOP red: Emergency stop button activated green: Emergency stop button not activated
3 Indicator lamp - compressed air green: Pressure OK orange: selected jet pressure not reached red: Pressure too low (below 0.15 MPa/1.5 bar)
4 Indicator lamp – dosing device green: Drive OK red: Error in drive
5 Indicator lamp - jet pistol green: Jet pistol OK orange: The trigger of the jet pistol was activated during the switch-on process red: Jet pistol disconnected or control line damaged
6 Display field

Jet equipment

1 Nozzle
2 Jet pistol
3 Trigger
4 Safety button

5 Coupling spray agent hose

6 Coupling of the control cable

Only with IB 7/40 Advanced:

7 Key for the dry ice dosing on/off Illuminates red when the dry ice dosaging is switched off
8 Increase the dry ice dosing
9 Key "increase jet pressure"
10 Key "decrease jet pressure"
11 Decrease the dry ice dosing

Start up

⚠️Danger

Risk of injury on account of flying dry ice pellets.

While preparing the appliance, check and ensure that all components, especially the spray agent hose are in proper condition. Replace damaged components with defect-free ones.

Clean dirty components and ensure that they are in proper working condition.

→ Place the machine on a horizontal, even surface and block the parking brakes of the steering rollers.
→ Connect the spray agent hose to the machine and secure it.
→ Connect the jet pistol to the spray agent hose and secure it.
→ Connect the control cable to the appliance.
→ Connect the control cable to the appliance.

Nozzles

Note

The choice of the nozzle depends on the material of the object to be cleaned and the contamination.

All nozzles can be screwed on top of the threading of the jet pistol without using any tools. The threaded surfaces on the nozzle are to be used to loosen tight nozzles using a spanner.

⚠️Danger

Risk of injury by the unit starting unintentionally. Switch off the unit before switching the nozzles.

⚠ Warning

Risk of injury by touching the cold nozzle. Warm up the nozzle before touching it or wear protective gloves.

Caution

Risk of cold welding Smear the enclosed grease on the nozzle threading before installing it.

Stream jets

1 Round jet nozzle, short
2 Round jet nozzle, long
3 Flat stream nozzle, short
4 Flat stream nozzle, long, included in delivery
5 Round stream nozzle, angled, with rubber coat
6 Flat stream nozzle, angled, with rubber coat
→ Place the nozzle onto the threaded suit port of the jet pistol and tighten it by hand.

Scrambler (accessory)

The scrambler crushes the dry ice pellets and is mounted between the jet pistol and the nozzle.

The alignment of the 4 holes plates in the scrambler indicates the degree of comminution.

Select the degree of comminution:

1 Screw connections
2 Magazine
3 Hole plate

→ Remove the screw connection.
→ Remove the magazine with hole plates.

→ Align the hole plates, as shown above, in the magazine (3 possibilities). The above specifications in the illustration refer to the size of the permeation openings.
→ Insert the magazine with hole plates into the scrambler.
→ Unscrew the screw connection and tighten it.

Nozzle extension (accessory)

An extension piece can be inserted between the jet pistol and the nozzle.

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Handle (accessory)

The handle can be fastened on the extension piece.

Simple line drawing of a bolt and nut (no text or symbols)

Working light (accessory)

Technical line drawing of a mechanical pulley or wheel assembly (no text or symbols)

The working light is connected between the jet pistol and the nozzle. Switching on and switching off is described in the chapter "Operation/Basic Settings".

Connect compressed air supply

Note

To ensure smooth functioning of the machine, the compressed air must have a low moisture content (max. 5% relative humidity, dewing point below 0°C). The compressed air must also be free from oil, dirt and foreign particles.

The compressed air must be dry and oil-free, at least one aftercooler and a separator must be downstream of the compressor.

→ Close pressure relief valve.
→ Connect the compressed air inlet pipe to the compressed air connection point of the device.

The maximum permissible supply pressure of 1 MPa (10 bar) must not be exceeded.

Establish mains contact

⚠️Danger

Risk of electric shock.

The socket to be used must have been installed by an electrician and be compliant with IEC 60364-1.

The appliance may only be connected to a electricity source with proper earthing.

The socket used must be accessible and at a height between 0.6 m and 1.9 m off the floor.

The socket used must be in the viewing area of the operator.

The machine must have an FI fuse of type B, 30 mA.

Check the mains cables of the machine each time before using the machine to see that it is not damaged. Never operate a ma-

chine with damaged cables. Get the damaged cables replaced by an electrician. The extension cord must be protected by IPX4 safety mechanism and the cables must at least be compliant with H 07 RN-F 3G1.5.

→ Insert the mains plug into the socket.

Operation

Filling dry ice

⚠️Danger

Risk of cold burns. Dry ice has a temperature of -79 °C. Never touch dry ice or cold parts of the machine without appropriate protection. Wear protective gloves and protective overalls.

→ Open the cover of the dry ice containe
→ Check the dry ice container for presence of foreign particles and condensate, remove them if found.
→ Fill dry ice pellets into the container.

Caution

Risk of damage to the device. Use only dry ice pellets as jet medium. The use of any other spray agent will lead to loss of warranty coverage.

→ Close the cover of the dry ice containe

Note

To avoid disruptions in operations on account of melted dry ice pellets, it would make sense to fully use up the contents of the dry ice container before adding fresh dry ice. If the machine is to remain idle for a longer time, operate the device until the dry ice container is empty or empty the container via the dry ice emptying function.

Settings

Note

The settings depend on the substances contained in the detergent and the type of dirt.

→ Release emergency-stop button by turning.
→ Set the appliance switch to "I".
→ Turn the keyswitch in a clockwise direction.
→ Increase/reduce the jet pressure by using the respective keys.

Note

The higher you set the jet pressure, so much greater (more aggressive) will the cleaning effect be.

→ Increase/reduce the dry ice dosing by using the respective keys.
→ Turn the keyswitch counter-clockwise and remove the key.

The automatic closure of the key hole will prevent contamination during operation.

When the key is removed, the device is protected against changes to the settings and resetting the statistics values.

Operation

→ Carry out maintenance jobs "daily before starting work" (see section "Maintenance and Care").

⚠️Danger

Risk of injury on account of flying dry ice pellets. Do not direct the jet pistol on persons. Keep third persons away from the place of use and when the machine is being operated (by cording off the area). Do not touch/hold the nozzle opening or the dry ice jet when the machine is running. First stop the compressed air supply before disconnecting the jet gun from the spray agent hose and the spray agent hose from the device; remove all pressure from the system and then pull the plug out of the socket.

→ Cordon off the working area to prevent persons coming close to the machine when it is being operated.

⚠️Danger

Risk of suffocation on account of carbon dioxide. The dry ice pellets are made of solidified carbon dioxide. The carbon dioxide content in the air at the place where the machine is used will increase when the machine is running. Ensure adequate ventilation at the place of use; if possible, use an alarm to warn persons. Symptoms of high levels of carbon dioxide in the air that is breathed in:

• 3...5%: headache, faster breathing.
• 7...10%: headache, nausea and perhaps even unconsciousness.

If any of these symptoms occur, please switch off the machine immediately and get a breath of fresh air; improve the ventilation before starting work again with the machine or use respirators.

Follow the safety specifications of the manufacturer of dry ice.

⚠️Danger

There is a danger because of dangerous to your health materials. If dust that is dangerous to your health can be generated, the appropriate safety measures will have to be taken prior to beginning work.

⚠️Danger

Risk of explosion!

Do not work on light metals and iron-containing substances simultaneously. If you alternate between working on light metals and iron-containing parts, the work area and the suction device must be cleaned between work cycles.

→ Ensure adequate ventilation while working in closed rooms in order to keep the carbon dioxide concentration in the atmospheric air in the room below the danger level.
→ Attach the object to be cleaned if necessary.

⚠️Danger

Risk of injury on account of electro-static discharge; risk of damage to the electronic components. The object being cleaned can get charged electrically during the cleaning process. Provide suitable earthing for the object being cleaned and ensure that the earthing remains intact during the entire cleaning process.

⚠ Warning

Risk of damage by foreign objects falling into the dry ice container. Keep cover of the dry ice container closed during operation.

→ Connect the grounding rope (with IB 7/40 Advanced only) electrically conductive with the cleaning object or ground the cleaning object in a different way.
→ Wear safety gear, safety gloves, close fitting safety goggles and ear-protection.
→ Switch on the compressed air supply.
→ Release emergency-stop button by turning.
→ Choose a safe place to stand, assume a secure body stance to avoid being thrown off-balance by the recoil pressure of the jet pistol.

In order to prevent the sudden recoil, a gradual increase of the jet pressure can be set up (see "Operation/Basic Setting", menu item "soft start").

→ Press in the safety knob of the jet pistol.
→ Activate the dry ice jet by pressing the trigger of the jet pistol and carry out the cleaning operation.

Note

With model IB 7/40 Advanced, the dosing of dry ice pellets can be switched on or off via the key dry ice dosing on/off on the jet pistol. When the dosing is turned off, the key illuminates red, the display shows "ice off".

In addition, with the IB 7/40 Advanced model, the jet pressure and the dry ice volume can be changed on the jet pistol.

⚠ Warning

Risk of damage to the dosing equipment on account of dirt. Keep the lid of the dry ice container closed during the spraying operation to prevent sprayed off dirt from entering it.

Switch-off in case of emergency

→ Release the trigger of the jet pistol.
→ Press emergency-stop button.

The dry ice dosing is topped and the air flow from the nozzle is interrupted.

→ Interrupt the compressed air supply.

Switching on after emergency-stop

→ Release emergency-stop button by turning.

Interrupting operation

→ Release the trigger of the jet pistol.
→ During breaks in operation, you can insert the jet pistol on the holder on the machine.

Note

During longer breaks in operations, the dry ice pellets can melt in the dry ice container. As far as possible, do not interrupt operations for more than 20 minutes. In case of extended interruptions, switch off the engine.

Drain off the condensate.

A water separator cleans the compressed air flowing to the device. This collects condensate in the water separator, that needs to be drained once in a while.

→ Place the collection trough under the condensate drain screw.
→ Open the pressure relief valve slowly and wait until the condensate has been drained from the device.

Note

Please dispose of condensate in an environmentally friendly manner.

Statistics functions

Retrieving values

→ Set the appliance switch to "I".
→ Press the Statistics key briefly to display the operating duration.
t: Operation duration since the last reset.
T: Total operating duration.

→ Press the Statistics key briefly to display the processed dry ice amount. m: Dry ice volume since the last reset. M: Total dry ice volume.
→ Press the Statistics key briefly to display the average dry ice consumption. q: Average dry ice consumption since the last reset.

Q: Average total dry ice consumption.

Reset values

→ Turn the keyswitch in a clockwise direction.
→ Press the statistics key for 4 seconds.

Note

The total values cannot be erased.

Basic settings

→ Press the keys to increase and decrease the jet pressure at the same time and hold them, turn the keyswitch clockwise.

In the operating mode basic settings, the keys have the following functions:

1 Increase value
2 Decrease value
3 Menu point to the top
4 Menu point to the bottom

Menue point	Setting range	Description
Soft start	0, 1, 2, 3, 4, 5 seconds	Soft start, duration until the selected jet pressure is reached
T_Dump	1, 2, 3, 4, 5 minutes	Duration of the dry ice emptying process
Language	metric, imperial	Measurement units metric: kg/h, MPa imperial: lbs, psi
Beleuchtung	ON/OFF Switch the nozzle lighting (option) on/off
Demo mode	ON/OFF Demo mode: The operation is simulated, compressed air and dry ice dispensing is locked.

Finish the basic settings

→ Turn the keyswitch counter-clockwise.

Shutting down

⚠️Danger

Risk of cold burns. Dry ice has a temperature of -79 °C. Never touch dry ice or cold parts of the machine without appropriate protection. Wear protective gloves and protective overalls.

⚠️Danger

Risk of injury on account of flying dry ice pellets. Do not direct the jet pistol on persons. Keep third persons away from the place of use and when the machine is being operated (by cording off the area).

→ Close the compressed air supply.
→ Place the collection trough under the condensate drain screw.
→ Open the pressure relief valve slowly and wait until the condensate and the compressed air have been drained from the device.
→ Place the collection trough under the dry ice exit.
→ Press the key to empty the dry ice and wait until the dry ice container is empty. The dry ice emptying stops after the preset time has elapsed (see "Basic Settings"). If needed, press the key to empty the dry ice container several times.

Note

Please dispose of condensate in an environmentally friendly manner.

→ Set the appliance switch to "0/OFF".
→ Disconnect the machine from the compressed air inlet.

→ Disconnect the main plug from the socket.
→ Clean and roll up the grounding rope.

Transport

⚠ Danger

Risk of accident on account of dry ice residue in the device. Remove all traces of dry ice before transporting the device in closed vehicle; otherwise there is a risk of carbon dioxide suffocation to the co-passengers.

Caution

Risk of injury and damage! Observe the weight of the appliance when you transport it.

→ Carry out all the steps listed in the chapter "Shut down" before transporting the device.
→ Mount the appliance on the transport vehicle.
→ Lock the breaks of the steering rollers.
→ Fasten the device to the vehicle using fastening belts.

Storage

Caution

Risk of injury and damage! Note the weight of the appliance in case of storage. This appliance must only be stored in interior rooms.

⚠Danger

Risk of suffocation due to accumulation of carbon dioxide. Store dry ice pellets only in areas that are well ventilated.

Maintenance and care

Maintenance instructions

The bases of a safe operating of the equipment is the regularly maintenance according to the following maintenance plan. Use exclusively original parts of the manufacturer or those parts recommended by him like

• parts and wearing parts,
  – accessories parts,
  – operating materials,
• cleaning agents.

⚠️DANGER

Risk of accident while working on the appliance. Carry out all the steps described in the chapter "Shut down" before starting anhy work on the device.

⚠️Danger

Risk of cold burns on account of dry ice or cold parts of the machine. While working on the machine, wear appropriate safety gear for protection against cold or remove dry ice and let the machine heat up. Never put dry ice in your mouth.

⚠ Warning

Risk of damage. Do not use solvents, petrol or oil-based cleaners to clean the jet pistol.

Maintenance contract

In order to guarantee a reliable operation of the equipment, we success, you signed a maintenance agreement. Please refer to your local Kärcher service department.

Maintenance schedule

Daily before starting operations

→ Check the spray agent hose for damages, bends and other damages. Soft areas in the hose indicate wear on the inner side of the hose. Replace the defective or worn out hose with a new hose.
→ Check electrical cable and plug for damages. Get defective parts replaced by Customer Service.

Every 100 operating hours

→ Check couplings of the spray agent hose, on the device, at the jet pistol for damages or wear and tear. Get Customer Service to replace the defective hose, defective couplings on the device or jet pistol.
→ Check dosing equipment for damages or leaks. If you find any damages/leaks, inform Customer Service.
→ Check the attachment caps of the rear wheels for proper seating.

Every 500 hours or once a year

→ Get the device checked by Customer Service.

Every 2 years

→ Replace the spray agent hose at least once in 2 years.

Opening the device

The side panels of the device must be removed to access the device for maintenance jobs:

1 Side panels

2 Snap closure

→ Turn the snap closure counter-clock-wise.
→ Remove side panel.

Maintenance Works

Replace the filter insert in the water separator.

1 Screw

2 Lower part

3 Nut

4 Disc

5 Filter inlay

6 Upper section

→ Loosen 4 screws.
→ Remove the lower part.
→ Unscrew the nut.
→ Remove the disc.

→ Remove the filter inlay and replace it with a new filter inlay.
→ Reassemble the water separator in the reverse sequence.

Tests

According to the specifications of BDV D 26, the following tests must be conducted by a technical expert. The results of the tests must be documented in a test report. The device operator must carefully store the test report until the next test.

After a working break of more than one year

→ Check the device to see that it is in a proper condition and is functioning well.

After changing the installation site

→ Check the device to see that it is in a proper condition, is functioning well and has been installed properly.

The operational safety of the device can get hampered on account of maintenance jobs or any modifications that have been done.

→ Check the device to see that it is in a proper condition, is functioning well and has been installed properly.

Troubleshooting

⚠️DANGER

Risk of accident while working on the appliance. Carry out all the steps described in the chapter "Shut down" before starting anhy work on the device.

Danger

Risk of cold burns on account of dry ice or cold parts of the machine. While working on the machine, wear appropriate safety gear for protection against cold or remove dry ice and let the machine heat up. Never put dry ice in your mouth.

Faults with display

Display Indicator lamp (KL)	Possible cause Remedy By whom
E001 KL control voltage glows red	Control voltage too low Turn off	the appliance, wait briefly, turn on the appli-ance once again.Have the socket checked.If this error recurs, please contact the Kärcher cus-tomer service department	Operator
E002 KL emergency stop glows red	Emergency-stop button has been pressed.	Release emergency-stop button by turning. Operator
E003 KL compressed air glows red	Pressure of the compressed air supply too low	Increase the pressure.Turn off the appliance, wait briefly, turn on the appli-ance once again.	Operator
E004 KL dosing glows red	Interference in the dosing Turn off	If this error recurs, please contact the Kärcher cus-tomer service department	Operator
E005 KL jet pistol glows red	Connection between the de-vice and the jet pistol is faulty.	Check for correct connection of the couplings in the control line.Check control cable for damages.	Operator
E006 KL jet pistol glows red	Short in jet pistol or control ca-ble	Replace the jet pistol or the jet hose with a control ca-ble.	Operator
E007 KL compressed air glows red	Fault in the compressed air regulator valve	Call Customer Service. Operator
E008 KL jet pistol glows orange	The trigger of the jet pistol was activated during the switch-on process or the releasing of the emergency stop key.	Release the trigger of the jet pistol. Operator

Faults without display on the console

Fault Possible cause	Remedy By whom
No display inspite of power switch in position 1	Mains Plug not connected to the socket. Insert the mains plug into a socket. Operator
	Fuse F1 blown Remove the side panel and unlock the fuse F1 by pressing on it.		Operator
No compressed air jet despite the trigger being drawn	Compressed air supply has too little pressure	Check pressure level. Operator
	Jet pressure is set too low Set the jet pressure to a higher level. Operator
	Power supply has been interrupted Check power supply. Indicator lamp "Device on" must glow green.		Operator
	Emergency-stop button has been pressed. Release emergency-stop button by turning. Indicator lamp "Device on" must glow green.		Operator
	Control cable not connected properly Check connection between control cable and the jet pistol and between the control cable and the device.		Operator
	Control cable is defective Replace spray agent hose. Operator
Compressed air jet is too weak	Jet pressure is set too low Set the jet pressure to a higher level. Operator
	Compressed air supply has too little pressure or the compressor output is low.	Check pressure and output.	Operator
	The filter insert in the water separator is plugged.	Replace the filter inlay in the water separator.	Operator
	Spray agent hose or jet pistol is blocked	Let the spray agent hose and jet pistol come to room temperature and remove the blocking. Increase working pressure and / or reduce the dry ice dosing.	Operator
No dry ice pellets in the compressed air jet	Dry ice dosing switched off (IB 7/40 Advanced only), button "Dry ice dosing on/off" on the jet gun lights glows red, display shows "Ice off".	Press the dry ice dosing key on the jet pistol. Operator
	Dry ice container is empty	Refill the dry ice container	Operator
	Dry ice has melted	Empty the dry ice container and refill it with fresh dry ice pellets.	Operator
	Vibrator on the dry ice container is not working	Call Customer Service.	Operator
	Drive motor of the dosing equipment is overloaded	Let the dosing thaw	Operator
	Compressed air is exiting into the dry ice container	Clean the pressure balance channel in the dosing equipment.	Customer Service
	Dosing disc in the dosing unit is defective	Replace the dosing disc.	Customer Service

Technical specifications

Electrical connection
Voltage V 220...240
Current type 1~
Frequency Hz 50
Connected load kW 0,6
Leakage current, typ. mA 7,5
FI safety switch delta I in A 0,03
Compressed air
Nominal width of hose Inch 1/2
Pressure supply (max.)	MPa (bar)	1,0 (10)
Pressure supply (min.)	MPa (bar)	0,2 (2)
Compressed air consumption	m3/min	0,5...3,5
Quality of compressed air	*
Performance data
Jet pressure (max.)	MPa (bar)	1,0 (10)
Diameter of dry ice pellets (max.)	mm	3
Dry ice consumption	kg/h	15...50
Dimensions
Contents of dry ice container	kg	15
Width	mm	510
Depth	mm	768
Height	mm	1096
Weight of IB 7/40 Classic, ready to operate	kg	93
Weight of IB 7/40 Advanced, ready to operate	kg	95
Weight of IB 7/40 Classic, empty, without accessories	kg	70
Weight of IB 7/40 Advanced, empty, without accessories	kg	71
Weight of the jet equipment (spray agent hose, spray gun, tool case)	kg	6,75
Recoil force of hand spray gun (max.)	N	30
Torque of jet pistol (max.), only with angled nozzle	N	8
Machine vibrations
Jet pistol	m/s2	1,2
Hose for spraying agent	m/s2	1,2
* dry and oil-free, at least one aftercooler and a separator must be downstream of the compressor

Compressed air demand

A Pressure in MPa
B Pressure in bar
C Volume stream in m 3/min
1 straight nozzles
2 angled nozzles

Sound

A Pressure in MPa
B Pressure in bar
C Noise level in dB(A)
1 Round jet nozzle, short
2 Flat stream nozzle, short
3 Flat jet nozzle, angled
4 Round jet nozzle, long
5 Flat stream nozzle, long, included in delivery

Sound power level

A Pressure in MPa
B Pressure in bar
C Noise level in dB(A)
1 Round jet nozzle, short
2 Flat stream nozzle, short
3 Flat jet nozzle, angled
4 Round jet nozzle, long
5 Flat stream nozzle, long, included in delivery

Accessories

Protective clothing

Full view protective goggles, anti-condensation, part no.: 6.321-208.0

Cold protection gloves with anti-slip profile, category III as per EN 511, part no.: 6.321-210.0

Ear protection with headgear, part no.: 6.321-207.0

Jet equipment

Round jet nozzle, short

Part no.: 4.321-236.0

Round jet nozzle, long

Part no.: 4.321-234.0

Flat stream nozzle, short

Part no.: 4.321-237.0

Flat stream nozzle, long, included in delivery

Part no.: 4.321-235.0

Round jet nozzle, angled

Part no.: 4.321-249.0

Flat jet nozzle, angled

Part no.: 4.321-250.0

Scrambler

Part no.: 4.110-015.0

Nozzle extension, 300 mm long

Part no.: 5.760-001.0

Handle

Part no.: 4.321-248.0

Working light

Part no.: 2.815-421.0

Warranty

The warranty terms published by our competent sales company are applicable in each country. We will repair potential failures of your appliance within the warranty period free of charge, provided that such failure is caused by faulty material or defects in fabrication. In the event of a warranty claim please contact your dealer or the nearest authorized Customer Service center. Please submit the proof of purchase.

EU Declaration of Conformity

We hereby declare that the machine described below complies with the relevant basic safety and health requirements of the EU Directives, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the machine is modified without our prior approval.

Product: Dry ice jet unit

Type: 1.574-xxx

Relevant EU Directives

2011/65/EU

2006/42/EC (+2009/127/EC)

2014/30/EU

2009/125/EG + 2009/1781

Applied harmonized standards

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 60204-1

EN 61000-3-2: 2014

EN 61000-3-3: 2013

EN IEC 63000: 2018

EN 62233: 2008

Applied national standards

GS-STE-13 (based on it)

The undersigned act on behalf and under the power of attorney of the company management.

Chairman of the Board of Management

Director Regulatory Affairs & Certification

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Declaration of Conformity

We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.

Product: Dry ice jet unit

Type: 1.574-xxx

Currently applicable UK Regulations

S.I. 2012/3032 (as amended)

S.I. 2008/1597 (as amended)

S.I. 2016/1091 (as amended)

2009/125/EC + 2009/1781

Applied designated standards

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 60204-1

EN 61000-3-2: 2014

EN 61000-3-3: 2013

EN IEC 63000: 2018

EN 62233: 2008

Applied national standards

GS-STE-13 (based on it)

The undersigned act on behalf and under the power of attorney of the company management.

Chairman of the Board of Management

Director Regulatory Affairs & Certification

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

⚠️Danger

1 Buse

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Line drawing of a mechanical bolt with a flanged cap (no text or symbols)

Technical line drawing of a mechanical pulley or wheel assembly (no text or symbols)

A Pression en MPa

B Pression en bar

A Pression en MPa

B Pression en bar

A Pression en MPa

B Pression en bar

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

Norme di sicurezza

⚠ Pericolo

Solo per IB 7/40 Advanced:

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Simple line drawing of a bolt with a flange and cap (no text or symbols)

Technical line drawing of a mechanical component with a central shaft and circular holes (no text or symbols)

1 Vite
2 Parte inferiore
3 Dado
4 Disco
5 Inserto filtro
6 Parte superiore

A Pressione in MPa

B Pressione in bar

A Pressione in MPa

B Pressione in bar

Winnenden, 2021/02/01

www.kaercher.com/REACH

⚠ Gevaar

Line drawing of a cylindrical mechanical part with flanged ends (no text or symbols)

Simple line drawing of a bolt and nut (no text or symbols)

Werkverlichting (accessoires)

Technical line drawing of a mechanical component with a central shaft and multiple circular holes (no text or symbols)

C Volumestroom in m 3/min

1 rechte sproeiers

2 gebogen sproeiers

Geluidsdrukniveau

A Druk in MPa

B Druk in bar

C Geluidsdrukniveau in dB(A)

A Druk in MPa

B Druk in bar

C Geluidsvermogensniveau in dB(A)

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

⚠Peligro

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Line drawing of a mechanical bolt with a flanged cap (no text or symbols)

Technical line drawing of a mechanical component with a central shaft and circular holes (no text or symbols)

1 Tornillo
2 Parte inferior
3 Tuerca
4 Arandela
5 Cartucho filtrante
6 Parte superior

Winnenden, 2021/02/01

www.kaercher.com/REACH

Avisos de segurança

Pure graphical symbols representing surveillance, human figures, a dog, and equipment (no text or labels)

⚠️Perigo

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Punho (acessório)

Line drawing of a mechanical bolt with a flanged cap (no text or symbols)

Technical line drawing of a mechanical component with a central shaft and circular holes (no text or symbols)

1 Revestimento lateral
2 Fecho rápido

1 Parafuso
2 Parte inferior
3 Porca
4 Anilha
5 Elemento filtrante
6 Parte superior

2006/42/CE (+2009/127/CE)

2014/30/UE

2009/125/EG + 2009/1781

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

Risiko

1 Kabelholder
2 Netkabel med netstik

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Håndgreb (tilbehør)

Simple line drawing of a bolt and nut (no text or symbols)

Technical line drawing of a mechanical pulley or wheel assembly (no text or symbols)

1 Skrue
2 Bund
3 Møtrik
4 Skive
5 Filterindsats
6 Top

A Tryk i MPa

B Tryk i bar

C Volumenstrøm i m 3/min

1 lige dyser

2 afvinklede dyser

Lydtrykniveau

A Tryk i MPa

B Tryk i bar

A Tryk i MPa

B Tryk i bar

C Lydeffektniveau i dB(A)

Dele-nr.: 4.321-235.0

Dele-nr.: 4.321-250.0

Scrambler

Dele-nr.: 4.110-015.0

Dele-nr.: 4.321-248.0

Arbejdsbelysning

Dele-nr.: 2.815-421.0

Garanti

2006/42/EF (+2009/127/EF)

2014/30/EU

2009/125/EG + 2009/1781

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

⚠️Fare!

1 Skyvebøyle
2 Deksel tørrisbeholder
3 Holder for strålepistol
4 Lagringsrom for tilbehør
5 Betjeningspanel
6 Kobling styreledning
7 Jordingskabel med klemme (kun IB 7/40 Advanced, opsjon ved IB 7/40 Classic)
8 Kobling strålemiddelslange
9 Styrerulle med holdebremse
10 Transporthåndtak, rammebeskyttelsesbøyle
11 Tørrisuttak, for tømming av beholderen

1 Dyse
2 Strålepistol
3 Avtrekkerhendel
4 Sikringsknapp
5 Kobling strålemiddelslange
6 Kobling styreledning

Kun for H 7/40 Advanced:

1 Rundstråledyse, kort
2 Rundstråledyse, lang
3 Flatstråledyse, kort
4 Flatstråledyse, lang, del av leveransen
5 Rundstråledyse, vinklet, med gummiarmering
6 Flatstråledyse, vinklet, med gummiarmering

1 Skrueforbindelse
2 Magasin
3 Hullplate

→ Skru av skrueforbindelsen.

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Handtak (tilbehør)

Håndtaket kan festes på forlengelsen.

Line drawing of a mechanical bolt with a flanged cap (no text or symbols)

Technical line drawing of a mechanical component with a central shaft and multiple circular holes (no text or symbols)

1 Skrue

2 Underdel

3 Mutter

4 Skive

5 Filterinnsats

6 Overdel

A Trykk i MPa
B Trykk i bar
C Volumstrøm i m 3/min
1 rette dyser
2 vinklede dyser

Lydtrykksnivå

A Trykk i MPa
B Trykk i bar
C Lydtrykksnivå i dB(A)
1 Rundstråledyse, kort
2 Flatstråledyse, kort
3 Flatstråledyse, vinklet
4 Rundstråledyse, lang
5 Flatstråledyse, lang, del av leveransen

Lydeffektsnivå

A Trykk i MPa
B Trykk i bar
C Lydeffektsnivå i dB(A)
1 Rundstråledyse, kort
2 Flatstråledyse, kort
3 Flatstråledyse, vinklet
4 Rundstråledyse, lang
5 Flatstråledyse, lang, del av leveransen

Tilbehør

Vernedrakt

Winnenden, 2021/02/01

www.kaercher.com/REACH

⚠️Fara

1 Munstycke

2 Strålspruta

3 Startspak

4 Låsknapp

5 Koppling med strålmedelslang

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Handtag (tillbehör)

Simple line drawing of a bolt and nut (no text or symbols)

Technical line drawing of a mechanical pulley or wheel component (no text or symbols)

1 Öka värde

2 Minska värde

3 Menypunkt uppåt

4 Menypunkt neråt

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

Turvaohjeet

⚠ Vaara

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Simple line drawing of a bolt and nut (no text or symbols)

Technical line drawing of a mechanical component with a central shaft and multiple circular holes (no text or symbols)

1 Sivuverhous

2 Pikakiinnitin

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

⚠️Κίνδυνος

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Line drawing of a bolt with a flanged cap (no text or symbols)

Technical line drawing of a mechanical component with a central shaft and multiple circular holes (no text or symbols)

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

Güvenlik uyarıları

Pure graphical symbols representing surveillance, human figures, a dog, and a device (no text or labels)

Tehlike

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Tutamak (aksesuar)

Simple line drawing of a bolt and nut (no text or symbols)

Technical line drawing of a mechanical pulley or wheel component (no text or symbols)

1 Yan kaplama
2 Mandal

1 Civata
2 Alt parça
3 Somun
4 Pul
5 Filtre kartuşu
6 Üst parça

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

⚠️ Опасность

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Line drawing of a mechanical component with a flanged top and cylindrical base (no text or symbols)

Technical line drawing of a mechanical pulley or wheel component (no text or symbols)

А Давление в МПа

В Давление в барах

А Давление в МПа

В Давление в барах

Winnenden, 2021/02/01

www.kaercher.com/REACH

Biztonsági tanácsok

⚠ Veszély

1 Tolókengyel

1 Kábel tartó

1 Csavarzat

2 Tár

3 Lyukaslemez

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Fogantyú (tartozék)

Line drawing of a mechanical component with a flanged top and cylindrical base (no text or symbols)

Technical line drawing of a mechanical component with a central shaft and circular holes (no text or symbols)

Chairman of the Board of Management

Director Regulatory Affairs & Certification

Winnenden, 2021/02/01

www.kaercher.com/REACH

Bezpečnostní pokyny

⚠️Nebezpečí

1 Držák kabelu

Pouze u IB 7/40 Advanced:

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Simple line drawing of a bolt and nut (no text or symbols)

Technical line drawing of a mechanical pulley or wheel component (no text or symbols)

2006/42/ES (+2009/127/ES)

2014/30/EU

2009/125/EG + 2009/1781

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

Varnostna navodila

⚠️ Nevarnost

1 Nosilec kabla
2 Omrežni kabel z omrežnim vtičem

1 Šoba

2 Brizgalna pištola

3 Sprožilna ročica

4 Varnostni gumb

5 Spoj gibke cevi brizgalnega sredstva

6 Spoj krmilnega voda

Le pri IB 7/40 Advanced:

1 Navojni spoj

2 Magazin

3 Luknjasta plošča

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Ročaj (pribor)

Simple line drawing of a bolt and nut (no text or symbols)

Technical line drawing of a mechanical pulley or wheel component (no text or symbols)

1 Stranska obloga
2 Hitro zapiralo

→ Hitro zapiralo odprite v nasprotni smeri urnega kazalca.

→ Snemite stransko oblogo.

Vzdrževanje

1 Vijak
2 Spodnji del
3 Matica
4 Kolut
5 Filtrni vložek
6 Zgornji del

→ Izvijte 4 vijake.
→ Snemite spodnji del.
→ Odvijte matice.
→ Odstranite kolut.
→ Snemite filtrni vložek in ga zamenjajte novim filtrnim vložkom.
→ Vodni ločevalnik ponovno sestavite v obratnem vrstnem redu.

Pregledi

V skladu z BGV D 26 mora strokovnjak na napravi opraviti naslednje preglede. Rezultate pregleda je potrebno podati pisno v Potrdilu o pregledu. Potrdilo o pregledu mora upravljavec naprave shraniti do naslednjega pregleda.

2006/42/ES (+2009/127/ES)

2014/30/EU

2009/125/EG + 2009/1781

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

Collection of symbolic icons including a lightning bolt, human figures, a dog, and a gear (no text or labels)

⚠ Niebezpieczeństwo

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Uchwyt (akcesoria)

Simple line drawing of a bolt and nut (no text or symbols)

Technical line drawing of a mechanical pulley or wheel component (no text or symbols)

2006/42/WE (+2009/127/WE)

2014/30/UE

2009/125/EG + 2009/1781

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

Măsuri de siguranță

⚠️ Pericol

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Mâner (accesoriu)

Simple line drawing of a bolt and nut (no text or symbols)

Technical line drawing of a mechanical pulley or wheel component (no text or symbols)

1 Mărirea valorii
2 Micşorarea valorii
3 Punctul de meniu de mai sus
4 Punctul de meniu de mai jos

A Presiune (MPa)
B Presiune (bar)
C Flux volumic (m 3/min)
1 Duze drepte
2 duze cotite

Nivel de zgomot

Directive UE respectate:

2011/65/EU

2006/42/CE (+2009/127/CE)

2014/30/UE

2009/125/EG + 2009/1781

Norme armonizate utilize:

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 60204-1

EN 61000-3-2: 2014

EN 61000-3-3: 2013

EN IEC 63000: 2018

EN 62233: 2008

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

⚠️Nebezpečenstvo

Len u IB 7/40 Advanced:

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Line drawing of a mechanical bolt with a flanged cap (no text or symbols)

Technical line drawing of a mechanical component with a central shaft and circular holes (no text or symbols)

2006/42/ES (+2009/127/ES)

2014/30/EU

2009/125/EG + 2009/1781

Uplatňované harmonizované normy:

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 60204-1

EN 61000-3-2: 2014

EN 61000-3-3: 2013

EN IEC 63000: 2018

EN 62233: 2008

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Prije prve uporabe Vašeg uređaja pročitajte ove originalne

www.kaercher.com/REACH

Sigurnosni napuci

⚠️ Opasnost

1 Potisna ručica
2 Poklopac spremnika za suhi led
3 Držač za brizgaljku
4 Odjeljak za pribor
5 Komandno polje
6 Kvačilo upravljačkog voda
7 Žica za uzemljenje sa stezaljkom (samo IB 7/40 Advanced, opcija kod IB 7/40 Classic)
8 Spojka crijeva za sredstvo za brizganje
9 Kotačić s pozicijskom kočnicom
10 Transportni rukohvat, zaštitni luk od udara
11 Izlaz za suhi led, za pražnjenje spremnika

1 Držač kabela
2 Strujni kabel sa strujnim utikačem

3 Dekompresijski ventil, pražnjenje kondenzata odvajača za kondenzat
4 Priključak za komprimirani zrak
5 Ispust kondenzata
6 Osigurač F1, ispod bočne oplate

Komandno polje

1 Mlaznica

2 Brizgaljka

3 Poluga okidača

4 Sigurnosni gumb

5 Spojka crijeva za sredstvo za brizganje

1 Vijčani spoj
2 Spremnik
3 Rupičasta ploča

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Rukohvat (pribor)

Rukohvat se može pričvrstiti na produžetku.

Simple line drawing of a bolt and nut (no text or symbols)

Radno svjetlo (pribor)

Technical line drawing of a mechanical pulley or wheel component (no text or symbols)

1 Bočna oplata
2 Bravica

1 Vijak
2 Donji dio
3 Matica
4 Pločica
5 Filtarski umetak
6 Gornji dio

→ Odvijte 4 vijka.
→ Skinite donji dio.
→ Odvijte maticu.
→ Skinite pločicu.
→ Filtarski umetak skinite i zamijenite novim filtarskim umetkom.
→ Separator vode ponovno sastavite obr nutim redoslijedom.

provjeravanje

A Tlak u MPa

B Tlak u bar

C Razina zvučnog tlaka u dB(A)

A Tlak u MPa

B Tlak u bar

C Razina zvučne snage u dB(A)

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

Pre prve upotrebe Vašeg uređaja pročitajte ove originalno uputstvo za rad, postupajte prema njemu i sačuvajte ga za kasniju upotrebu ili za sledećeg vlasnika.

Pregled sadržaja

www.kaercher.com/REACH

Sigurnosne napomene

Uređaj se smije koristiti samo od osoba, koje su pročitale upustvo za upotrebu i koji su je razumjeli. Moraju se uvažavati sve sigurnosne napomene.

→ Upustvo za upotrebu čuvati na taj način, tako da je korisniku dostupna u svakom trenutku.

Stepeni opasnosti

⚠️ Opasnost

Ukazuje na neposredno preteću opasnost koja dovodi do teških telesnih povreda ili smrti.

⚠Upozorenje

Ukazuje na eventualno opasnu situaciju koja može dovesti do teških telesnih povreda ili smrti.

Oprez

Ukazuje na eventualno opasnu situaciju koja može dovesti do lakših telesnih povreda ili izazvati materijalnu štetu.

Simboli na aparatu

⚠️ Opasnost

Opasnost od povrede kroz leteće pelete suhog leda. Mlazni pištolj ne uperivati na osobe. Ostale osobe udaljiti od mjesta obavljana rada i udaljiti ih od mjesta dok je mašina u pogonu (npr. kroz ograničavanje).

Tokom pogona na dirati pipu ili u Trockeneisstrahl.

⚠️ Opasnost

Opasnost od trovana kroz ugljen dioksid. Pelete suhog leda se sastoje od čvrstog ugljen dioksida. Kod pogona uređaja raste količina ugljen dioksida u zraku na radnom mestu. Radno mesto dovoljno izračiti, po potrebi koristiti uređaj za upozorenje osoblja. Znak visoke koncentracije ugljen dioksida u zraku:

• 3...5%: Glavobolja, visoka frekvencija disanja.
• 7...10%: Glavobolja, povraćanje i eventualno gubljenje svesti.

Kod pojave ovih naznaka uređaj odmah ugasiti i izaći na svež zrak, prije nastavka rada poboljšati mere prozračivanja ili koristiti uređaj za disanje.

Ugljendioksid je teži od vazduha i sakuplja se u uskim, niskim prostorima ili u zatvorenim posudama.

Pobrinite se za dovoljnu ventilaciju na radnom mestu.

1 Potisna ručica
2 Poklopac rezervoara za suhi led
3 Držač za mlazni pištolj
4 Pregrada za odlaganje pribora
5 Komandno polje
6 Spojnica voda upravljača
7 Žica za uzemljenje sa stezaljkom (samo IB 7/40 Advanced, opcija kod IB 7/40 Classic)
8 Spojnica cijevi mlaznog sredstva
9 Točkić sa pozicionom kočnicom
10 Transportna ruka, Rammschutzbügel
11 Izlaz za suhi led, za ispražnjavanje rezevoara

1 Držač kabla
2 Strujni kabl sa utikačem
3 Dekompresioni ventil, pražnjenje kondenzata odvajača za kondenzat
4 Priključak zraka pod pritiskom
5 Izlaz kondenzata
6 Osigurač F1, ispod bočne oplate

Komandno polje

1 Brizgaljka
2 Mlazni pištolj
3 Okidač
4 Sigurnosno dugme
5 Spojnica cijevi mlaznog sredstva
6 Spojnica voda upravljača
7 Tipka za doziranje suhog leda upaljeno / ugašeno Svetli crveno kod ugašenov doziranja suhog leda
8 Povećati tipku za doziranje suhog leda.
9 Povećati tipku za mlazni pritisak.
10 Umanjiti tipku za mlazni pritisak.
11 Umanjiti tipku za doziranje suhog leda.

Samo kod IB 7/40 Advanced:

Stavljanje u pogon

⚠️Opasnost

1 Zavrtni spoj
2 magazin
3 rupčasta ploča

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Drška (pribor)

Drška može na produženju biti pričvrsčena.

Simple line drawing of a bolt and nut (no text or symbols)

Technical line drawing of a mechanical component with a central shaft and multiple circular holes (no text or symbols)

Radno osvetljenje se montira između mlaznog pištolja i pipe. Paljenje i gašenje je opisano u poglavlju "Upravljanje/osnovne postavke".

1 Povećati vrednost
2 Smanjiti vrednost
3 Tačku menija prema gore
4 Tačku menija prema dole

Tačka menija	Raspon podešavanja	Opis
Soft početak	0, 1, 2, 3, 4, 5 sekunde	Lagani start, trjanje do dostizanja izabranog pritiska mlaza
T_Dump	1, 2, 3, 4,5 minuta	Trajanje procesa ispražnjavanja suhog leda
jezik	metric, imperial	jedinice merenja metric: kg/h, MPa imperial: lbs, psi
osvetljenje	Paljenje/ gašenje	Osvetljenje pipe (opcija) upaliti / gasiti
Demo-Modus	Paljenje/ gašenje	Pogon za demonstraciju: Upravljanje se simulira, izlaz zraka pod pritiskomi suhog leda se ograničava.

1 Bočna oplata

2 Bravica

→ Bravicu otvorite u smeru suprotno od kazaljke na satu.
→ Skinite bočnu oplatu.

Radovi na održavanju

Filter zameniti u rezaču vode

1 Zavrtanj
2 Donji deo
3 Navrtka
4 Pločica
5 Filter
6 Gornji deo

→ Odvijte 4 zavrtnja.

→ Skinuti donji deo.

→ Maticu odvrnuti

A Pritisak u MP
B Pritisak u barima
C Nivo zvučnog pritiska u dB(A)

1 Pipa za okrugli mlaz, kratka
2 Pipa za ravni mlaz, kratka
3 Ravna mlazna pipa, kutna
4 Pipa za okrugli mlaz, duga
5 Pipa za ravni mlaz, duga, u okviru dostave

Nivo zvučne snage

A Pritisak u MP
B Pritisak u barima
C Nivo zvučnog pritiska u dB(A)

1 Pipa za okrugli mlaz, kratka
2 Pipa za ravni mlaz, kratka
3 Ravna mlazna pipa, kutna
4 Pipa za okrugli mlaz, duga
5 Pipa za ravni mlaz, duga, u okviru dostave

Pribor

Zaštitna odeća

Zaštitne naočale za potpuni pregled, otporno na udar, broj dela: 6.321-208.0 Zaštitne rukavice za hladnoću sa antiklizećimprofilom, kategorija III po EN 511, broj dela: 6.321-210.0 Zaštita za uši sam slušalicama, broj dela: 6.321-207.0

Mlazni uređaj

Pipa za okrugli mlaz, kratka

Kataloški br.: 4.321-236.0

2006/42/EZ (+2009/127/EZ)

2014/30/EU

2009/125/EG + 2009/1781

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

Collection of symbolic icons including a lightning bolt, human figures, a dog, and a battery (no text or labels)

⚠️ Опасност

1 Завинтване
2 Магазин
3 Перфорирана пластина

Line drawing of a cylindrical mechanical part with flanged ends (no text or symbols)

Simple line drawing of a cylindrical object with a flanged top and lid (no text or symbols)

Technical line drawing of a mechanical pulley or wheel assembly (no text or symbols)

Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

⚠️Oht

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Käepide (tarvikud)

Line drawing of a mechanical bolt with a flanged cap (no text or symbols)

Technical line drawing of a mechanical pulley or wheel assembly (no text or symbols)

1 Küljepaneel
2 Kiirlukk

1 Kruvi
2 Alumine osa
3 Mutter
4 Seib
5 Filtripadrun
6 Ülemine osa

A Rõhk (MPa)
B Rõhk (baari)
C Helirōhu tase, dB (A)
1 Ümardüüs, lühike
2 Lamedüüs, lühike
3 Lamedüüs, nurga all
4 Ümardüüs, pikk
5 Lamedüüs, pikk, tarnekomplektis

Müratase

A Rõhk (MPa)
B Rõhk (baari)
C Müratase, dB (A)
1 Ümardüüs, lühike
2 Lamedüüs, lühike
3 Lamedüüs, nurga all
4 Ümardüüs, pikk
5 Lamedüüs, pikk, tarnekomplektis

Tarvikud

Kaitseriietus

Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

Drošības norādījumi

⚠ Bīstami

Tikai IB 7/40 Advanced:

Line drawing of a cylindrical mechanical part with flanged ends (no text or symbols)

Simple line drawing of a bolt and nut (no text or symbols)

Technical line drawing of a mechanical component with a central shaft and circular holes (no text or symbols)

1 Skrūve

2 Apakšdaļa

3 Uzgrieznis

4 Paplāksne

5 Filtra ieliktnis

6 Augšdaļa

A Spiediens megapaskālos (MPa)
B Spiediens bāros (bar)
C Trokšna spiediena līmenis dB(A)
1 Apaļas strūklas sprausla, īsa
2 Plakanstrūklas sprausla, īsa
3 Plakanstrūklas sprausla, sagriezta len- kī
4 Apaļas strūklas sprausla, gara
5 Plakanstrūklas sprausla, gara, piegā- des komplektā

A Spiediens megapaskālos (MPa)
B Spiediens bāros (bar)
C Trokšna jaudas limenis dB(A)
1 Apalas strūklas sprausla, īsa
2 Plakanstrūklas sprausla, īsa
3 Plakanstrūklas sprausla, sagriezta len- kī
4 Apalas strūklas sprausla, gara
5 Plakanstrūklas sprausla, gara, piegā- des komplektā

Piederumi

Aizsargapgērbs

Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

www.kaercher.com/REACH

Saugos reikalavimai

⚠️Pavojus

1 Stūmimo rankena

2 Sauso ledo kameros dangtis

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Rankena (priedas)

Simple line drawing of a bolt and nut (no text or symbols)

Technical line drawing of a mechanical pulley or wheel component (no text or symbols)

1 Varžtas

2 Apatinė dalis

3 Veržlé

4 Diskas

5 Filtro kasetė

6 Viršutinė dalis

Chairman of the Board of Management

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/02/01

⚠️Обережно!

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

Рукоятка (аксесуар)

Line drawing of a mechanical component with a flanged top and cylindrical base (no text or symbols)

Technical line drawing of a mechanical pulley or wheel assembly (no text or symbols)

Winnenden, 2021/02/01

www.kaercher.com/REACH

安全说明

△ 危险

1 螺旋连接
2 料仓
3 孔板

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

手柄（配件）

手柄可以固定到加长件上。

Line drawing of a mechanical bolt with a flanged cap (no text or symbols)

工作照明（配件）

Technical line drawing of a mechanical pulley or wheel component (no text or symbols)

1 增大数值
2 减小数值
3 菜单项向上
4 菜单项向下

1 侧板
2 快速封扣

a(

b(

.1. المسماعير

1. الجزء السفلاى

.3ة

.4 _U

.1. كسوة جانية

.2. أداة شیت سربع

.1 زيادة القيمة

تقليل القيمة .2

نقطة القائمة إلى .3

أعلى.

نقطة القائمة إلى .4

أسفل

Simple line drawing of a bolt with a flanged cap (no text or symbols)

Technical line drawing of a mechanical pulley or wheel assembly (no text or symbols)

.1 وصلة

العملة .2

.3. لوح مُتَقَبَ

• قم ب Falk الوصلة

Line drawing of a cylindrical mechanical component with flanged ends (no text or symbols)

الفوهة

.1. فوهة الشعاع

لَة. فوهة الشعاع

1. فوهات الشعاع

.1 حامل الإكابل

.1ä

Black silhouette of a hand giving a thumbs-up gesture (no text or symbols)

THANK YOU!

MERCI! DANKE! iGRACIAS!

Register your product and benefit from many advantages.

www.kaercher.com/welcome

Rate your product and tell us your opinion.

Icon showing a gear and wrench inside a square frame (no text or symbols)

www.kaercher.com/dealersearch

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28-40

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]