SMV6ZCX19E - Dishwasher BOSCH - Free user manual and instructions

Brand	Bosch
Model	SMV6ZCX19E
Product type	Fully integrated built-in dishwasher
Dimensions (H x W x D)	81.5 cm x 59.8 cm x 55.0 cm (adjustable height)
Net weight	Approx. 50 kg
Power supply	230 V, 10 A, 50 Hz
Capacity (place settings)	13 standard place settings
Wash programs	Eco 50°C, Auto, Intensive 70°C, Speed 65°C, Silent Clean 50°C, Pre-wash
Additional functions	Intensive Zone, EmotionLight, TimeLight, Angle light bar, Vario drawer
Safety	Child safety, Anti-overflow protection, Glass protection, Door lock
Maintenance and cleaning	Filter cleaning, spray arms, door seal, limescale detection
Spare parts and repairability	Worktop, basket, Vario drawer, spray arm, filters, power cord, detergent cover, wastewater pump, side panel, door, control panel, door springs, plinth, base plate, overflow pipe, inner door, hinge, door seal, EmotionLight, TimeLight, Gap illumination
Settings	Water hardness, rinse aid dosage, drying intensity
Certifications	Compliant with eco-design standards (2021), VDE 0701

Frequently Asked Questions - SMV6ZCX19E BOSCH

How to reset the Bosch SMV6ZCX19E dishwasher?

To reset, press the On/Off button for about 3 seconds until the cycle end indicator turns off. Close the door and restart a program.

What are common error codes?

Error code E15 indicates a water leak in the protection tray. Check hoses and seals. Error code E09 means a heating problem. Refer to the manual for the meaning of all codes.

How to clean the dishwasher filters?

Turn the coarse filter counterclockwise and remove the filtration system. Clean the fine filter under running water using a brush. Reassemble by aligning arrows and turning clockwise until it clicks into place.

The dishwasher does not start, what to do?

Check that the door is properly closed and the lock engages. Make sure the water supply is open and the electrical outlet is powered. If the problem persists, contact customer service.

How to adjust the water hardness?

Turn on the appliance, then press the button corresponding to the water hardness key (often identified by a drop symbol). Select the hardness range according to your area (test with a test strip). Confirm by pressing Start.

What is the capacity of this appliance?

The Bosch SMV6ZCX19E can hold up to 13 standard place settings, with an adjustable upper basket and a Vario drawer for small items.

How to replace the upper spray arm?

Unscrew the upper spray arm (Torx T20 screwdriver) and pull it downwards to remove. Insert the new arm and screw firmly by hand. Check that it rotates freely.

The salt indicator is lit, what to do?

Fill the salt reservoir located under the lower basket after unscrewing the cap. Use a funnel to avoid spills. Wipe up any excess and screw the cap back on.

How to improve drying performance?

Use a rinse aid and adjust the dosage according to the manual. Select the Intensive program or activate the Extra dry function if available. Leave the door slightly open at the end of the cycle.

Where to buy spare parts?

You can order original parts from the Bosch Home & Garden website or from authorized dealers. Refer to the part numbers listed in the repair manual (e.g., [00614935] for the tablet guide).

USER MANUAL SMV6ZCX19E BOSCH

4.2 Mounting the system from the chimney

4.2.1 Mounting the shelf for the 86-cm model 9 4.2.2 Mounting the extractor for the chimney 9 4.2.3 Mounting the vaporizer insert 10

4.3 Replacing the varioDrawer drawer 11

4.3.1 Removing the varioDrawer drawer 11 4.3.2 Mounting the varioDrawer drawer 12

4.4 Replacing the spray frame 13

4.4.1 Removing the spray frame 13 4.4.2 Mounting the spray frame 13

4.5 Replacing the filter 14

4.5.1 Removing the filter 14 4.5.2 Mounting the filter 14

4.6 Mounting the front panel for the table 15

4.7 Replacing the power cable 16

4.7.1 Disconnecting the power cable 16 4.7.2 Connecting the power cable 16

4.8 Replacing the cap for the detergent 17

4.8.1 Removing the cap for the detergent 17 4.8.2 Installing the spring 17 4.8.3 Mounting the cap for the detergent 17

4.9 Replacing the drain hose 18

4.9.1 Removing the drain hose 18 4.9.2 Mounting the drain hose 18

4.10 Replacing the door leaf 19

4.10.1 Removing the door leaf 19 4.10.2 Installing the door leaf 20

4.11 Replacing the outer door 21

4.11.1 Removing the outer door 21 4.11.2 Installing the outer door 21

4.12 Replacing the control panel 23

4.12.1 Removing the control panel 23 4.12.2 Installing the control panel 23

4.13 Fixing the spring-loaded door 24

4.14 Replacing the bottom panel 26

4.14.1 Removing the bottom panel 26 4.14.2 Installing the bottom panel 26

4.15 Replacing the main contact plate 27

4.15.1 Removing the main contact plate 27 4.15.2 Installing the main contact plate 27

4.16 Replacing the overflow pipe 28

4.16.1 Removing the overflow channel 28 4.16.2 Installing the overflow pipe 29

4.17 Replacing the inner door 31

4.17.1 Removing the inner door 31 4.17.2 Installing the inner door 31

4.18 Replacing the door gasket

4.18.1 Removing the door gasket 32 4.18.2 Installing the door gasket 32

4.19 Replacing the door seal (bottom) 34

4.19.1 Removing the door seal 34 4.19.2 Installing the door seal 35

4.20 Replacing the door seal (top) 36

4.20.1 Removing the door seal 36 4.20.2 Installing the door seal 36

Repair tips - Washing machine

4.21 Replacing EmotionLight 37

4.21.1 Removing EmotionLight 37 4.21.2 Installing EmotionLight 37

4.22 Replacing TimeLight 40

4.22.1 Removing TimeLight 40 4.22.2 Installing TimeLight 40

4.23 Replacing Gap illumination (product lighting) 41

4.23.1 Removing Gap illumination 41 4.23.2 Installing Gap illumination 42

About this document

1.1 Important information

1.1.1 General

These instructions are for the repair of the device by the user, in accordance with the regulations for environmentally sound design of devices (from 03.2021).

They contain information about the replacement of certain spare parts, including warnings and risks.

If you have any questions, please contact our customer service. We are not liable for damages unless the repair instructions have been followed correctly.

1.2 Explanation of symbols

1.2.1 Danger levels

Warnings are indicated by the symbol of a warning triangle. The signal word indicates the severity of the danger.

Ниво на п dedурждени 3начени
ОПАСHОCT	Еспаразы新股у на п dedурждени.TО сбоб Shedени по Смьт ини сернони наразяваим.
ПРEDУПЕЖДЕНЕ	Еспаразы新股у на п dedурждени.TOT сбob Shedени по Смьт ини сернони наразяваим.
ВИМATEЛНО	Еспаразы新股у на п dedурждени.TOT сбob Shedени по Смьт ини наразяваим.
ВИМАМЕЛ	Еспаразы新股у на п dedурждени.TOT сбob Shedени по Смьт ини onMy-шостевни по.TI.

Table 1: Danger levels

1.2.2 Danger symbols

The danger symbols are pictograms that provide information about the type of danger.

The following danger symbols are used in this document:

Симbol 3a onachocst 3nauchene
!	ОвноPre dedуpeinteilno сьобсяне
	Опасост ot eilektprucecco наржени
	Риск OT ekspлозя
	Опасost ot поязвany

About this document

Симbol 3a onachoct 3начени	Опachoct ot пемарази Опachoct ot горец поьрхости
	Опachoct ot симно магнисто плел Опachoct ot неюни рашу лычени

Table 2: Danger symbols

1.2.3 Structure of warnings

The warnings in this document have a standardized format.

DANGER

Immediate danger / warning

Safety measures to prevent danger.

Specific example shows a warning for electric shock, caused by parts under voltage. The symbol for danger is placed.

DANGER

Risk of electric shock from live parts!

Electric shock

Disconnect the electrical supply before servicing or maintenance.

1.2.4 General symbols

This document uses the following general symbols:

Оьш симвов Зачени
I	Иденихицаре на спесиален сбBet(TEKCT w/ллграфика)
I	Иденихицаре на постс сбBet (само TEKCT)
I	Иденихицаре на врьзka Кьм Вideо урок
I	Иденихицаре на необхочимite И-стру金融市场
I	Иденихицаре на необхочимite поедырпелли усповия
I	Иденихицаре на усповie (ako ..., Тогава ... )
I	Иденихицаре на рeshуntat
[Стар]	Иденихицаре на Клиочни SFYTOH
[00123456]	Иденихицаре на Каталожен Homep
[Статус]	Иденихицаре на по��азаня TEKT/ празорец (надиспега на урда)

Table 3: General symbols

Safety

2.1 General safety instructions

2.1.1 All household appliances

Risk of electric shock from the device!

• Before repair, including electrical components, disconnect the device from the power supply!
• Disconnect the device from the electrical supply for at least 60 seconds before starting work. Before starting, check the safety instructions according to VDE 0701 and the national standards.

Risk of injury from sharp edges!

Wear protective gloves.

Risk of injury during repair, maintenance, or servicing of the device. Disconnect the device from the power supply and ensure it cannot be reconnected.

Wear protective footwear. Secure the technical components so they cannot fall. Do not allow contact of body parts with moving components.

Safety risk for the device and the device! - Use only original spare parts. Risk of damage to electrostatic sensitive components (ESD) due to improper handling, including printed circuit boards.

Tools and auxiliary means

посочане Робносту Избражения
Оверты Торх T20 С овор [00340764]	100 MM, за виHTове с преда- зен удиФТ
Оверты Торх T15	Дылжина 80 MM
Плеска OTberрта Врьх 10 MM x 1,6 MM x 200 MM
Кleineц с Истовд- ни челков [00340871]	Дылжина: 200 MM, пави

Repair

4.1 Work area safety

Removal:

Remove the device from the packaging. The device is free.

4.1.1 Work area setup

1. Insert the screw into the hole (1) (optional). 2. Press the clamping screw into the work area opening (2).

1. Turn the workpiece over. (3). 4. Tighten the working screws (4). 5. Remove the working screws.

4.1.2 Mounting on the working plate

1. Insert the workpiece into the working plate by turning the locking screw (1).

1. Press the workpiece down (2).
2. Turn the handle to the working plate until the required clamping force is achieved (3). 4. Tighten the opposite screw (4) (optional).

Repair

4.2 Mounting the cup system

Requirement:

The corresponding cup is removed from the hub.

4.2.1 Mounting the cup for the 86-cm model

Special tools:

Water cup [00614935] Cup retainer [00618565]

1. Place the cup diagonally into the front part of the hub. 2. Center and press the cup into place.

4.2.2 Mounting the cup retainer

Special tools:

Water hose [00614935] Filter for water [00618565]

According to the data, the water filter may be clogged. To check, remove the filter and clean it. If the filter is clogged, it should be replaced. If the water pressure is low, the filter should be cleaned.

1. Remove the plastic cover.

2. Turn the filter counterclockwise.

3. Remove the filter.

Repair

1. Place the item for me.

4.2.3 Mounting the generator block

Special tools:

Water hose [00614935]

4.10.2 Mounting the side panel

1. Place the side panel in the groove of the base (1).

Fig. 2: Installation diagram

2. Press the side panel onto the groove (2). 3. Secure the side panel with screws (3).

Repair

4.11 Adjusting the inlet door

Warning:

The adjustment excludes locking. The adjustment excludes the supply line.

4.11.1 Removing the inlet door

Simply turn the screws, as described in the relevant section.

1. Remove the door 2. Unscrew the four screws.

3.

Secure the door, which is on the other side.

Unscrew the door screw.

4.11.2 Mounting the inlet door

Repair

Warning:

The insulating jacket is correctly positioned on the outside of the inlet door. The inlet door is painted.

1. Close the inlet door, without slamming it.
2. Press the control panel door release button (1).

1. Pull the door towards you and open it (2).

4.

Close the doors, pressing the left side first.

Open the doors and secure them with the bolts (metal 4 x 11 mm screws).

5. Secure the filter (metal 4 x 11 mm screws).

Repair

4.12 Replacing the control panel

If the control panel is defective, the control panel must be replaced.

Removal:

Disconnect the appliance from the power supply. Disconnect the appliance from the water supply. The door is closed. The door is closed (optional heater/heater).

4.12.1 Removing the control panel

1. Disconnect the electrical connections to the control panel. Remove the sensor for the detergent (1,2).

2. Disconnect the grounding cable (3) (optional). 3. Open the door of the device. 4. Secure the control panel, following the pre-drilled holes (screw it).

5. Check the gate.

6. Check the control panel.

4.12.2 Mounting the control panel

Use screws 4 x 16 mm.

Mount it in reverse.

Repair

4.13 Fixing the spring of the gate

1. Guide the cable through the conduit.

2.1. Open the gate slightly (1).

2. Fix the bracket to the base (2).

1. Close the gate gently (3).

The cable system is automatically attached to the gate leaf.

Repair

3.1. Close the gate slightly (4).

1. Press the lever to release the gate leaf (5).
2. Remove the protective cap (6).

1. Remove the protective cap by turning it counterclockwise.

Installation of the main contact in the reverse direction.

Repair

4.16 Replacing the overflow hose

The overflow hose is located at the back of the lower part of the appliance.

Removal:

The appliance is disconnected from the power supply. Disconnect the appliance from the water supply. The furniture panel is removed (if any). The top door is removed. The lower panel is removed (if any). →26 The control panel is removed. →27

4.16.1 Removing the overflow hose

Residual water

When removing the drain hose, residual water may leak out. Collect the water in a suitable container.

1. Release the locking mechanism (1,2).

1. Release the fasteners of the element

Repair

3.1. Place the screwdriver under the metal strip (1). 2. Carefully release the metal clip (2).

1. The overflow pipe is not required.

4.16.2 Mounting the overflow pipe

Water damage can occur if the overflow pipe is not mounted correctly!

Insert the overflow pipe into the water inlet and secure it to the base.

Fix the overflow pipe in place at the opening.

1. Insert the overflow pipe (1).
2. Place the overflow pipe into the seal (2).
3. Press the overflow pipe into the water seal (3).
4. Insert the overflow pipe wall (4). 5. Fix the overflow pipe (5).

Repair

1. Check the installation thoroughly. 3. Check the distance and the stop position.

4. Secure with metal brackets on the left and right sides.

4.20.2 Mounting the door seal

The seal must be installed at the correct height. It is 1750 mm for doors with a height of 81 cm and 1850 mm for doors with a height of 86 cm.

1. Prepare the seal for the door. 2. Check the correct position for mounting the seal profile.

1. The current must be switched off before the seal is installed.

4

The seal must not be deformed when installed. The seal is cut to the appropriate length and inserted into the container opening.

Place the seal correctly so that it covers the entire door. The seal must be flush with the outer edge of the container.

Correctly installed door seal:

Repair

4.21 Replacing the EmotionLight

The EmotionLight is located at the top front edge of the reservoir.

Removal:

The device is disconnected from the power supply. The device is disconnected from the mains. The devices are freely accessible. The work area is clean (dry). The work area is clean (dry).

4.21.1 Replacing the EmotionLight

1. Remove the mounting bracket from the rear (1).

1. Press the tab upwards (2).
2. Remove the connector cover (according to the device type).

4. Disconnect the electrical connection from the charging module.

1. Remove the EmotionLight from the device.

4.21.2 Mounting the EmotionLight

1. Place the bracket on the mounting frame for the backup power supply (1).

Repair

2. Grasp the hook of the fixator (2).

3

ATTENTION!

Incorrect mounting!

Route the cable in the area of the door hinge.

Mount the cable in the hinge area of the door (between the hinge plate and the backup power supply) so that it cannot be damaged by moving parts.

Mount the cable on the tension side.

Repair

Fig. 3: Cable routing

4. Remove the cover.

4.23 Lamp for gap illumination (illumination of the product)

Removal:

Remove the plug from the socket. Remove the plug from the power supply. The front door is open. The operating panel is removed.

4.23.1 Removing the gap illumination lamp

1.1. Remove the fixator (1).

2. Disconnect the electrical connection from the operating module (2).

2.1. Remove the cover of the rear fixator (1).

2. Remove the damp cloth (2).

Repair

3.1. Remove the cover of the fixator (1).

1. Pull the printed circuit board towards the rear and out of the frame of the operating module (2).

4.23.2 Mounting the gap illumination

1. Place the printed circuit board in the frame of the operating module.

1. Mount the optical damp and tighten it until you have the correct adjustment.

4. Connecting the power cable to the dishwasher.

4.1 Replacing the top panel 90

4.1.1 Removing the top panel 90 4.1.2 Installing the top panel 90

4.2 Installing the cutlery basket system 91

4.2.1 Installing the tablet dispenser on 86 cm models 91 4.2.2 Installing the cup holder 91 4.2.3 Installing the steam insert 92

4.3 Replacing the varioDrawer drawer 93

4.3.1 Removing the varioDrawer drawer 93 4.3.2 Installing the varioDrawer drawer 94

4.4 Replacing the spray arms 95

4.4.1 Removing the spray arm 95 4.4.2 Installing the spray arm 95

4.5 Replacing the filters 96

4.5.1 Removing the filter 96 4.5.2 Installing the filter 96

4.6 Installing the spray head for baking sheets 97

4.7 Replacing the power cable 98

4.7.1 Pulling out the power cable 98 4.7.2 Connecting the power cable 98

4.8 Replacing the detergent dispenser cover 99

4.8.1 Removing the detergent dispenser cover 99 4.8.2 Inserting the spring 99 4.8.3 Installing the detergent dispenser cover 99

4.9 Replacing the drain pump cover 100

4.9.1 Removing the drain pump cover 100 4.9.2 Installing the drain pump cover 100

4.10 Replacing the side panel 101

4.10.1 Removing the side panel 101 4.10.2 Installing the side panel 102

4.11 Replacing the outer door 103

4.11.1 Removing the outer door 103 4.11.2 Installing the outer door 103

4.12 Replacing the control panel 105

4.12.1 Removing the control panel 105 4.12.2 Installing the control panel 105

4.13 Repairing the door springs 106

4.14 Replacing the bottom panel 108

4.14.1 Removing the bottom panel 108 4.14.2 Installing the bottom panel 108

4.15 Replacing the socket plate in the base 109

4.15.1 Removing the socket plate in the base 109 4.15.2 Installing the socket plate in the base 109

4.16 Replacing the overflow pipe 110

4.16.1 Removing the overflow drain 110 4.16.2 Installing the overflow pipe 111

4.17 Replacing the hinged doors 113

4.17.1 Removing the hinged doors 113 4.17.2 Installing the hinged doors 113

4.18 Replacing the door hinges 114

4.18.1 Removing the door hinges 114 4.18.2 Installing the door hinges 114

4.19 Replacing the (lower) door seal 116

4.19.1 Removing the door seal 116 4.19.2 Installing the door seal 117

4.20 Replacing the (upper) door seal 118

4.20.1 Removing the door seal 118 4.20.2 Installing the door seal 118

4.23 Replacing the Gap Illumination

Requirement:

4.22.1 Removing the timeLight 163 4.22.2 Installing the timeLight 163

4.23 Replacing the Gap illumination 164

4.23.1 Removing the Gap illumination 164 4.23.2 Installing the Gap illumination 165

4.21.2 Installing the emotionLight

1. Place the holder in the flush tank's frame (1).

Repair

1. Activate the locking hook (2).

3.

NOTE

Incorrect mounting!

4.22 Replacing the timeLight

4.22.1 Removing the timeLight

4.22.2 Installing the timeLight

4.23 Replacing the Gap illumination

Presetting:

4.23.2 Installing the Gap illumination

1. Place the circuit board holder in the operating module's frame.

1. Fasten it with a "click" sound.

2.1 General Safety Instructions 212

2.1.1 All domestic appliances 212

Tools and aids. 213

Repair 214

4.1 Replacing worktop 214

4.1.1 Removing worktop 214 4.1.2 Installing worktop 214

4.2 Installing basket system 215

4.2.1 Installing a tab slide for the 86 cm model 215 4.2.2 Installing cup support clip 215 4.2.3 Installing steamer insert 216

4.3 Replacing varioDrawer 217

4.3.1 Removing varioDrawer 217 4.3.2 Installing varioDrawer 218

4.4 Replacing spray arms 219

4.4.1 Removing spray arm 219 4.4.2 Installing spray arm 219

4.5 Replacing filters 220

4.5.1 Removing filter 220 4.5.2 Installing filters 220

4.6 Installing baking sheet spray head 221

4.7 Replacing power cord 222

4.7.1 Unplugging power cord 222 4.7.2 Plugging in power cord 222

4.8 Replacing detergent cover 223

4.8.1 Removing detergent cover 223 4.8.2 Inserting spring 223 4.8.3 Installing detergent cover 223

4.9 Replacing wastewater pump cover 224

4.9.1 Removing wastewater pump cover 224 4.9.2 Installing wastewater pump cover 224

4.10 Replacing side panel 225

4.10.1 Removing side panel 225 4.10.2 Installing side panel 226

4.11 Replacing outer door 227

4.12 Replacing control panel 229

4.12.1 Removing control panel 229 4.12.2 Installing control panel 229

4.19 Replacing (lower) door seal 240

4.19.1 Removing the door seal 240 4.19.2 Installing the door seal 241

4.20 Replacing (upper) door seal 242

4.20.1 Removing door seal.. 242 4.20.2 Installing door seal 242

Repair hints - Dishwasher

4.21 Replacing EmotionLight 243

4.21.1 Removing EmotionLight 243 4.21.2 Installing EmotionLight 243

4.22 Replacing TimeLight 246

4.22.1 Removing TimeLight 246 4.22.2 Installing TimeLight 246

4.23 Replacing Gap illumination 247

4.23.1 Removing Gap illumination 247 4.23.2 Installing Gap illumination 248

Concerning this document

1.1 Important information

1.1.1 Purpose

These repair hints support consumers to repair appliances by themselves according to the applicable eco-design regulation (as of 03/2021).

They contain information on how to exchange defined spare parts, including warnings and risks.

In case of questions, please contact our customer service. We will only be liable for damages if the repair hints have been followed properly.

1.2 Explanation of symbols

1.2.1 Danger levels

The warning levels consist of a symbol and a signal word. The signal word indicates the severity of the danger.

Table 1: Danger levels

Warning level Meaning
Danger	Non-observation of the warning message will result in death or serious injuries.
Warning	Non-observation of the warning message could result in death or serious injuries.
Caution	Non-observation of the warning message could result in minor injuries.
Notice	Non-observation of the warning message could result in damage to property.

1.2.2 Hazard symbols

Hazard symbols are symbolic representations which give an indication of the kind of danger.

The following hazard symbols are used in this document:

Hazard symbol Meaning
!	General warning message
	Danger from electrical voltage
	Risk of explosion
	Danger of cuts
	Danger of crushing

Concerning this document

Hazard symbol Meaning
	Danger from hot surfaces
	Danger from strong magnetic field
	Danger from non-ionizing radiation

Table 2: Hazard symbols

1.2.3 Structure of the warnings

Warnings in this document have a standardised appearance and a standardised structure.

Danger

Type and source of danger!

Possible consequences of ignoring the danger / warning.

Measures and prohibitions for preventing the danger.

The following example shows a warning that warns against electric shock due to live parts. The measure for avoiding the danger is mentioned.

Danger

Risk of electric shock due to live parts!

Death by electrocution

• Disconnect appliances from the electrical supply at least 60 seconds before disconnecting for repairs.

1.2.4 General symbols

The following general symbols are used in this document:

Gen. symbol Meaning
1	Identification of a special tip (text and/or graphic)
i	Identification of a simple tip (only text)
	Identification of a link to a video tutorial

Gen. symbol Meaning
	Identification of required tools
	Identification of required preconditions
	Identification of a condition (if ..., then ...)
	Identification of a result
[Start]Identification of a key or button
[00123456] Identification of a material number
Status Identification of displayed text / window(in the appliance's display)

Table 3: General symbols

Safety

2.1 General Safety instructions

2.1.1 All domestic appliances

Risk of electric shock due to live parts!

Errors during repairs involving electrical components can lead to electrical shock! - Disconnect the appliance from the mains for at least 60 seconds before starting work. After the repair, have a safety test performed according to VDE 0701 or country-specific regulations.

Risk of injury from sharp edges!

Wear protective gloves.

Risk of crushing during repair, maintenance, troubleshooting, and service due to heavy and moving components.

Wear protective shoes. - Secure heavy components from falling down. - Do not stick body parts into moving components.

Risk to the appliance's safety / function! Only use original spare parts.

Risk of damage to electrostatically sensitive components (ESDs)! - Do not touch the modules, including connections and conductor paths.

Tools and aids

Designation Details Images
Screwdriver Torx T20 with bore hole [00340764]	100 mm, for screws with safety pin
Insulated Screw- driver Torx T15 with bore hole [15000626]	Blade length 125 mm, for screws with safety pin
Slotted screwdriver	Blade 10 mm x 1.6 mm x 200 mm
Needle nose pliers [00340871]	Length: 200 mm, straight

4.1 Replacing worktop

Prerequisite:

Appliance is disconnected from the power supply. Appliance is freely accessible.

4.1.1 Removing worktop

1. Remove the two screws at the back (1) (optional).
2. Press both catch levers under the worktop upwards (2).

1. Lift the worktop slightly at the front (3).
2. Push worktop away towards the rear (4).
3. Remove worktop.

4.1.2 Installing worktop

1. Lock the rear of the worktop into the guides using the retaining collars (1).

1. Push worktop forwards (2).
2. Press the front of the worktop downwards until both catch levers click audibly into place (3).
3. Screw in the two screws again (4) (optional).

Repair

4.2 Installing basket system

Prerequisite:

The relevant basket has been removed from the appliance.

4.2.1 Installing a tab slide for the 86 cm model

Required tools:

Tabguide [00614935] Cup support clip [00618565]

1. Insert the tab slide diagonally at the front of the basket.
2. Centre and click the tab chute into place.

4.2.2 Installing cup support clip

Required tools:

Tabguide [00614935] Cup support clip [00618565]

When washing cups, the cup support clip can be folded up. The additional angle reduces the collection of water on the bottom of cups. In the case of tall glasses we recommended leaving the cup support clip folded down. If upper baskets have an optional plastic insert, they must first be removed.

1. Remove the plastic insert.

1. Click the cup support clip into place.

1. Fold up the clip.

Repair

1. Position the items to be washed.

4.2.3 Installing steamer insert Required tools:

Tabguide [00614935] Cup support clip [00618565]

• Wedge the steamer insert with the end pieces under the basket system.

Repair

4.3 Replacing varioDrawer

4.3.1 Removing varioDrawer

1. Bend the handle flaps inwards.

1. Remove the handle upwards.
2. Press plastic side inserts outwards and press them upwards out of the frame.

Repair

1. Carefully bend the guide tabs outwards.

1. Pull the folding spines out of the tabs.
2. Press metal frame at the front out of the holders.

1. Push metal frame back out of the guide.

4.3.2 Installing varioDrawer

Install in reverse order.

Repair

4.4 Replacing spray arms

4.4.1 Removing spray arm

1. Unscrew the upper spray arm (1) and pull down to remove (2).

1. Pull down the lower spray arm to remove.

4.4.2 Installing spray arm

1. Insert the lower spray arm. The spray arm clicks into position.
2. Insert the upper spray arm and screw it firmly in place.

Repair

4.5 Replacing filters

4.5.1 Removing filter

1. Turn the coarse filter anticlockwise (1) and remove the filter system (2).

Check that no foreign objects fall into the sump.

1. Pull down the micro filter to remove.

4.5.2 Installing filters

1. Re-assemble the filter system. Make sure that the locking catches on the coarse filter click into position.
2. Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up.

Repair

4.6 Installing baking sheet spray head

1. Remove top basket.
2. Insert the baking sheet spray head in the holder (1) and turn to the right (2).

The baking sheet spray head clicks into position.

Repair

4.7 Replacing power cord

Prerequisite:

The appliance is disconnected from the power supply. The appliance is disconnected from the water supply. The appliance is freely accessible.

4.7.1 Unplugging power cord

• Move the plug of the power cord carefully up and down and pull it out of the mains socket.

4.7.2 Plugging in power cord

Notice

Overheating of main connection!

Risk of fire

Firmly insert the power cord until it clicks.

• Insert the plug of the power cord into the mains socket until the plug clicks audibly into place.

Repair

4.8 Replacing detergent cover

A small screwdriver can be used as a levering tool.

Prerequisite:

Appliance is disconnected from power supply. Appliance is disconnected from water supply. Door has been opened. Detergent cover has been opened.

4.8.1 Removing detergent cover

1. Slide the detergent cover in 5 mm.
2. Lever the detergent cover on the lower side out of the guide rails and take the detergent cover on the upper side out of the guide rails.
3. Remove the spring.

4.8.2 Inserting spring

1. Insert the long end of the spring into the mounting hole of the dispenser device (1).

1. Insert the short end of the spring into the mounting hole of the detergent cover (2).
2. Press cover into the dispenser device (3).

4.8.3 Installing detergent cover

1. Insert the detergent cover 5 mm before the completely open position into the guide rails on one side. Applying gentle force, press the opposite side into the guide rails.
2. Check the function of the detergent cover.

Repair

4.9 Replacing wastewater pump cover

Prerequisite:

Basket has been removed. Filters have been removed. See page 220.

4.9.1 Removing wastewater pump cover

1. Scoop out any water.

Use a sponge if necessary.

1. Pry off the pump cover using a spoon and grip it by the crosspiece.

1. Lift the pump cover inwards at an angle and remove.

4.9.2 Installing wastewater pump cover

Insert the pump cover (1) and press down (2).

The pump cover clicks into position.

Repair

4.10 Replacing side panel

Prerequisite:

Appliance is disconnected from power supply. Appliance is disconnected from water supply. Appliance is freely accessible. Free-standing appliances: Worktop has been removed. See page 214.

4.10.1 Removing side panel

1. Remove screws from the side panel (1).

Fig. 1: Fully integrated

1. Tilt the side panel slightly outwards at the top (2).
2. Lower the side panel and pull it out of the base trough (3).

Repair

4.10.2 Installing side panel

1. Insert the side panel into the base trough (1).

Fig. 2: Fully integrated

1. Press the side panel onto the appliance (2).
2. Secure the side panel with screws (3).

Repair

4.11 Replacing outer door

Prerequisite:

Appliance is disconnected from power supply. Appliance is disconnected from water supply.

Just remove the screws which are described in the following steps.

1. Open door.
2. Remove four screws.

3

Secure the door by holding it on one side.

Remove two screws.

Insulating fleece has been correctly positioned and fixed on the inside of the outer door. Hinges are inserted into the outer door.

1. Close the inner door without snapping it shut.
2. Push the outer door upwards underneath the control panel (1).

1. Press the outer door against the inner door and hold (2).

4.

Secure the door by holding it on one side.

Open the door and secure it with two screws (4 x 11 mm metal screws).

1. Secure the outer door with four screws (4 x 11 mm metal screws).

Repair

4.12 Replacing control panel

If an operating module is defective, the entire control panel must be replaced.

Prerequisite:

The appliance is disconnected from the power supply. The appliance is disconnected from the water supply. The outer door has been removed. The outer door has been removed (fully integrated/integrated).

4.12.1 Removing control panel

1. Disconnect electrical connections from the control panel and the low rinse-aid sensor (1, 2).

1. Disconnect the earth cable (3) (optional).
2. Open the appliance door.
3. Secure the control panel to prevent it from falling down (hold on to it).
4. Remove six screws.

1. Remove the control panel.

4.12.2 Installing control panel

Use screws 4 x 16 mm.

Install in reverse order.

Repair

1. Remove cord guide cover out.

2.1. Open door slightly (1).

1. Fix in the groove of the base trough (2).
2. Slowly close the door (3).

The cord system attaches itself automatically to the door hinge.

Repair

3.1. Slightly close the door (4).

1. Move the groove to the back and release the door hinge (5).
2. Open the door (6).

1. Repeat the process again on other side of appliance.

Repair

4.14 Replacing toe panel

The feet are identical and can be swapped over.

Prerequisite:

Appliance is disconnected from power supply. Appliance is disconnected from water supply. Outer door has been removed. Outer door has been removed (fully integrated/integrated).

4.14.1 Removing toe panel

1.

Incorrect removal. If the toe panel is loosened at the side and removed, the two brackets may break away. If only one bracket is damaged, the side can be changed as the brackets are identical. It is advisable to place something under the appliance at the front on the side to relieve the load on the toe panel with the feet.

1. Reach into the guides (1) with a screwdriver and release the catch by pushing downwards.

1. Lift the panel off.
2. Remove the feet forwards (1).

4.14.2 Installing toe panel

1. Insert the feet.
2. Attach the toe panel at the top (1) and press it down until it audibly clicks into place (2).

Repair

4.15 Replacing base socket plate

The base socket plate is located in the lower area at the front.

Prerequisite:

Appliance is disconnected from power supply. Appliance is disconnected from water supply. Furniture panel (optional) has been removed. Outer door has been removed. Outer door has been removed (fully integrated/integrated). Toe panel has been removed (optional). See page 232.

4.15.1 Removing base socket plate

1. Remove two screws (1).

1. Disengage catch elements (2).
2. Tilt the base socket plate carefully forwards (1).

4.

Depending on the model series, the plug to the EmotionLight is still secured to the base.

Unlock the plug on the catch tappet and pull to the rear (optional) (2).

4.15.2 Installing base socket plate

Install the base socket plate in reverse order.

Repair

4.16 Replacing overflow conduit

The overflow conduit is located in the front lower area of the appliance.

Prerequisite:

Appliance is disconnected from power supply. Appliance is disconnected from water supply. Furniture panel has been removed (optional). Outer door has been removed. Toe panel has been removed (optional). See page 232. Base socket plate has been removed. See page 233.

4.16.1 Removing overflow channel

Residual water

• When the drainage hose is removed, residual water may run out. Catch water or remove from the base pan with suction syringe.
• Lever out of the catch mechanism at the top (1, 2).

1. Release catch element at top.

3.1. Insert screwdriver below metal brake (1).

1. Gently release metal clip (2).

Repair

1. Lift overflow conduit off.

4.16.2 Installing overflow conduit

Water damage due to incorrect installation of the overflow conduit! Correctly insert the overflow conduit at the bottom into the guide of the base trough. Click the overflow conduit correctly into place at the top.

1. Place overflow conduit (1).
2. Move overflow conduit into seal (2).
3. Press overflow conduit in guide of seal (3).
4. Insert overflow conduit concisely (4).
5. Clip in overflow conduit (5).

Repair

1. Check installation left and right. 3. Check firm seat.

1. Clip in metal clip on left and right side.

Repair

4.17 Replacing inner door

Prerequisite:

The appliance is disconnected from the power supply. The appliance is disconnected from the water supply.

4.17.1 Removing inner door

1. Remove screws (1).
2. Remove inner door upwards (2).

4.17.2 Installing inner door

1. Fold door seal to the front.
2. Move inner door behind the door seal.
3. Close inner door.
4. Fold door seal upwards. Side parts show up.
5. Move door hinge upwards.
6. Secure door hinge with screws.
7. Place inner door on door hinge.
8. Secure inner door with screws.

Repair

4.18 Replacing door hinge

Prerequisite: Appliance is disconnected from power supply. Appliance is disconnected from water supply. Appliance is freely accessible. Side panel has been removed. (See page 225) Outer door has been removed. Inner door has been removed. Control panel has been removed. (See page 229) Door springs have been fixed. (See page 230) Toe panel has been removed. (See page 232) Base socket plate has been removed. (See page 233) Overflow channel has been removed. (See page 234)

Appliance is disconnected from power supply. Appliance is disconnected from water supply. Appliance is freely accessible. Side panel has been removed. -> Page 225. Outer door has been removed. Inner door has been removed. Control panel has been removed. -> Page 229. Door springs have been fixed. -> Page 230. Toe panel has been removed. -> Page 232. Base socket plate has been removed. -> Page 233. Overflow channel has been removed. -> Page 234.

1. Release catch hook with a screwdriver (1).
2. Pull door hinge forwards (2).

1. Place hinge on appliance (1).

1. Place hinge on appliance (1).
2. Move hinge downwards (2) until it is latched to the appliance.

2.

A missing ground connection can lead to mains potential on door.

Establish ground connection.

Repair

4.19 Replacing (lower) door seal

Prerequisite:

Appliance is disconnected from power supply. Appliance is disconnected from water supply. Outer door has been removed. Base socket plate has been removed. (See page 233) Toe panel has been removed (optional). (See page 232) Door springs have been removed. Control panel has been removed. Cable harness holder on bottom right has been removed.

4.19.1 Removing the door seal

1. Remove the two retaining clips on the lower door seal (1, 2).

1. Detach the overflow channel.

1. Lift the overflow gutter off.

Repair

1. Remove the lower door seal from the inner door.

4.19.2 Installing the door seal

1. Fit the sealing caps on the left and right to the sealing rail with the door seal.

1. Insert the door seal with the sealing flap in the inner door.
2. Secure the door seal with two retaining clips.

Repair

4.20 Replacing (upper) door seal

Prerequisite:

The appliance is disconnected from the power supply. The appliance is disconnected from the water supply.

4.20.1 Removing door seal

Remove the door seal from the inner frame.

4.20.2 Installing door seal

The door seal must be cut to the correct length before installation. This is 1750 mm for appliances of 81 cm in height and 1850 mm for appliances of 86 cm in height.

1. Prepare the appropriate door seal.
2. Ensure correct installation position of the sealing profile.

1. The white dot must be level with the sealing bed strip.

4

The sealing must not be wavy or stretched at corners. The seal is cut off diagonally at the ends and tapers away into the bottom of the container at the front.

Position the end of the seal straight to the front underneath the inner door. The seal should lie against the side of the container as far as possible.

Correctly installed door seal:

Repair

4.21 Replacing EmotionLight

The EmotionLight is situated in the upper front exterior area of the rinsing tank.

Prerequisite:

The appliance is disconnected from the power supply. The appliance is disconnected from the water supply. The appliance is freely accessible. The worktop has been removed (optional). The right-hand side panel has been removed (optional). See page 225.

4.21.1 Removing EmotionLight

1. Detach the catch hook at the rear (1).

1. Remove the holder upwards (2).
2. Pull the plug out of the connector (bottom right at the front of the appliance).
3. Remove the electrical connection from the power module.

1. Remove the EmotionLight from the appliance.

4.21.2 Installing EmotionLight

1. Insert the holder into the rinsing tank frame (1).

Repair

1. Engage the catch hook (2).

3.

Install the cable on the right lower side.

Repair

Fig. 3: Flat cable

1. Insert the plug.

Repair

4.22 Replacing TimeLight

Replace the TimeLight only as a complete part. The TimeLight module is fixed to the rear of the base socket plate.

Prerequisite:

Appliance is disconnected from power supply. Appliance is disconnected from water supply. Toe panel has been removed. See page 232. Base socket plate has been removed and turned. See page 233.

4.22.1 Removing TimeLight

1. Bend the catch elements (1) slightly outwards.

1. Pull the TimeLight module upwards out of the guide (2).

4.22.2 Installing TimeLight

1. Bend the catch elements (1) back again.

1. Push the TimeLight module into the guide (2).
2. Connect the electrical connection.

Repair

4.23 Replacing Gap illumination

Prerequisite:

The appliance is disconnected from the power supply. The appliance is disconnected from the water supply. The outer door is disassembled. The operation panel has been removed.

4.23.1 Removing Gap illumination

1. Detach catch (1).
2. Remove the electrical connection from the operation module (2).

1. Detach catch hook at rear (1).
2. Remove light fibre (2).

Repair

3.1. Detach catch hook (1).

1. Lift up PCB with holder and remove it from operation module frame (2).

4.23.2 Installing Gap illumination

1. Insert PCB holder to operation module frame.

1. Tighten it with a "click" sound.

1. Install light fibre and tighten it with a "click" sound.

1. Connect wire to operation module.

1.1.1 Purpose 251 1.2 Explanation of symbols 251 1.2.1 Safety devices 251 1.2.2 Safety symbols 251 1.2.3 Structure of warnings 252 1.2.4 General symbols 252

Safety 253

2.1 General safety instructions 253 2.1.1 All household appliances 253

Table 1: Safety devices

1.2.2 Safety symbols

1.1 Important information 333

3. Start-up to begin.

1. The device is to be operated and maintained

4.2.3 Device operation with internal components:

The tablet [00614935] and the control unit [00618565] were replaced - start the device with the internal components and the external parts.

EMIOKEUN

4.3 Replacing the drawer

1. Remove the "EmotionLight" and set it aside.

4.2.1.2 "EmotionLight" installation

4.23.2 Installing the Gap Illumination

4.17.1 Removing an interior door 731 4.17.2 Installing an interior door 731

4.18 Replacing the door hinge 732

4.18.1 Removing the door hinge 732 4.18.2 Installing the door hinge 732

4.19 Replacing the (lower) door seal 734

4.19.1 Removing the door seal 734 4.19.2 Installing the door seal 735

4.20 Replacing the (upper) door seal 736

4.20.1 Removing the door seal 736 4.20.2 Installing the door seal 736

Troubleshooting tips - Dishwasher

4.21 Replacing the EmotionLight 737

4.21.1 Removing the EmotionLight 737 4.21.2 Installing the EmotionLight 737

4.22 Replacing the TimeLight 740

4.22.1 Removing the TimeLight 740 4.22.2 Installing the TimeLight 740

4.23 Replacing the Gap Illumination 741

4.23.1 Removing the Gap Illumination 741 4.23.2 Installing the Gap Illumination 742

4.17.1 Removing the inner door

4.17.2 Installing the inner door

4.23.1 Removing the Gap Illumination

1. Release the catch (1).
2. Disconnect the electrical connection of the operating module (2).

2.1. Release the catch (1). 2. Remove the optical fiber (2).

Repair

3. 1. Release the catch (1).

4.23 Replacing Gap illumination 823

4.23.1 Removing Gap illumination 823 4.23.2 Installing Gap illumination 824

About this document

4.23 Replacing Gap illumination

Requirement:

4.23 Replacing Gap illumination

Prerequisite:

The appliance is disconnected from the power supply. The appliance is disconnected from the water supply. The outer door has been removed. The control panel has been removed.

4.23.1 Removing the gap illumination

1. Release the latch (1).
2. Disconnect the electrical connection from the control module (2).

2.1. Release the locking hook at the rear (1).

1. Remove the light guide (2).

Repair

3.1. Release the locking hook (1).

4.23.2 Installing the gap illumination

1. Insert the circuit board into the frame of the control module.