KA450 - Sander BLACK & DECKER - Free user manual and instructions

USER MANUAL KA450 BLACK & DECKER

Your BLACK+DECKER KA450 quarter sheet sander has been designed for sanding wood, metal, plastics and painted surfaces. This tool is intended for consumer use only.

Safety instructions

General power tool safety warnings

Warning! Read all safety warnings, instructions, illustrations and specifications provided with power tool. Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injur

Save all warnings and instructions for future reference. The term "power tool" in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.

1. Work area safety
   a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
   b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
   c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2. Electrical safety
   a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
   b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
   c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
   d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
   e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
   f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
   a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
   b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
   c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

1. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and greasy

ENGLISH

(Original instructions)

surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Service

a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

Warning! Additional safety warnings for sanders

Warning! Contact with or inhalation of dusts arising from sanding applications may endanger the health of the operator and possible bystanders. Wear a dust mask specifically designed for protection against dust and fumes and ensure that persons within or entering the work area are also protected.

Hold power tool by insulated gripping surfaces when performing an operation where the sanding accessory may contact hidden wiring. Accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
- Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

Warning! Take special care when sanding some woods (e.g. beech, oak) and metal which may produce toxic dust. Wear a dust mask specifically designed for protection against toxic dust and fumes and ensure that persons within or entering the work area are also protected.

Warning! Use this tool in a well ventilated area when sanding ferrous metals. Do not operate the tool near flammable liquids, gases or dust. Sparks or hot particles from sanding or arcing motor brushes may ignite combustible materials.

Warning! Do not sand magnesium! There is a risk of fire or explosions.

Thoroughly remove all dust after sanding.
The intended use is described in this instruction manual. The use of any accessory or attachment or performance of any operation with this tool other than those recommended in this instruction manual may present a risk of personal injury and/or damage to property.

Safety when sanding paint

Warning! Observe the applicable regulations for sanding paint. Pay special attention to the following:

• Whenever possible, use a vacuum extractor for dust collection.
  Take special care when sanding paint which is possibly lead based and may produce toxic dust:

Do not let children or pregnant women enter the work area.
All persons entering the work area should wear a mask specially designed for protection against lead paint dust and fumes.
Do not eat, drink or smoke in the work area.

Dispose of dust particles and any other removal debris safely.

Safety of others

This tool can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the tool. Cleaning and user maintenance shall not be made by children without supervision.

Residual risks

Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings. These risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks can not be avoided. These include:

Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or accessories.
Injuries caused by prolonged use of a tool. When using any tool for prolonged periods ensure you take regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed when using your tool (example:- working with wood, especially oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by EN62841 and may be used for comparing one tool with another.

The declared vibration emission value may also be used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used. The vibration level may increase above the level stated.

When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time.

Labels on tool

The following symbols are shown on the tool along with the date code:

Warning! To reduce the risk of injury, the user must read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.

• If the supply cord is damaged, it must be replaced by the manufacturer or an authorised BLACK+DECKER Service Centre in order to avoid a hazard.

Using an extension cable

Always use an approved extension cable suitable for the power input of this tool (see technical data). Before use, inspect the extension cable for signs of damage, wear and ageing. Replace the extension cable if damaged or defective. When using a cable reel, always unwind the cable completely. Use of an extension cable not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and electric shock.

Features

This tool includes some or all of the following features.

1. On/off paddle switch
2. Lock-on/lock off slider
3. Sanding pad
4. Paper clamp
5. Dust port
6. Canister

Assembly

Warning! Before assembly, make sure that the tool is switched off and unplugged.

Attaching 1/4 sheet sandpaper (fig.A)

Warning! lock the sander off during sanding disc installation. Refer to "Lock Off" section.

Lift clamps up with your thumb, (Fig. A). Rotate the clamp (4) downward until the clamp is fully opened.
Lay sandpaper on a flat surface and, centering the pad of the unit, press the sander down firmly onto the paper.
Wrap ends of the sandpaper around ends of the sander pad and clamp them in place using the clamps.
To close clamps, rotate clamp handles back up as far as they will go and lock them in place. Stretch sandpaper as tight as possible when clamping.

Note: On new tools the sandpaper may be difficult to install because of the stiffness of the sanding pad. This condition will improve as the pad compresses over time.

Fitting sanding sheets with nylon loops

Make sure that the tool is switched off and unplugged.
Press the sheet firmly and evenly onto the sanding base making sure that the holes in the sheet line up with the holes in the base.

Use

Warning! Let the tool work at its own pace. Do not overload.

On/off

Hold the sander as shown in Figure C and squeeze so the paddle (1) depresses without putting pressure on the workpiece.
To turn the tool off, release the paddle.

Operation

Grasp the sander as shown in figure B and turn it ON. Move it in long, sweeping strokes along the surface, letting it do the work.

Pushing down on the tool while sanding actually slows the removal rate and produces an inferior quality finish.

Check your work often. Sander is capable of removing material rapidly especially with coarse paper.

Lock on/lock off slider

This sander is equipped with a switch that allows you to lock it on for extended use, and lock off to prevent accidental actuation.

ENGLISH

(Original instructions)

Lock on (Fig. C)

To lock the tool on, depress the paddle (1) with one hand and push the slider (2) right to the locked position with your other hand as shown in Figure C.
To stop the tool, push the slider left to the unlocked position and release paddle.

Lock off (Fig. D)

To lock the tool OFF, make sure the paddle (1) is not depressed and push the slider (2) right to the locked position. The paddle cannot be depressed while switch is in locked position.
To unlock the paddle, push the slider left to the unlocked position. The paddle can now be depressed.

Dust Collection

Warning! Collected sanding dust from sanding surface coatings (polyurethane, linseed oil, etc.) can selfignite in sander dust bag or elsewhere and cause fire. To reduce risk, empty bag frequently and strictly follow sander manual and coating manufacturer's instructions.

To attach the canister to the sander, line up the grooves (8) in the canister (6) with the nubs (9) on the dust port (5). Ensure the longer side (10) of the canister opening is on the top side of the port.
Slide the canister onto the dust port and turn the canister clockwise to lock it in place as shown in Figure F.
To remove, turn the canister counterclockwise and slide the canister off.
To empty the canister, remove it from the dust port and dump the sanding debris into an appropriate trash receptacle.

Maintenance

Your BLACK+DECKER corded tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on the tool, switch off and unplug the tool.

Regularly clean the ventilation slots in your tool and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do not use any abrasive or solvent-based cleaner.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be fitted:

Safely dispose of the old plug.
Connect the brown lead to the live terminal in the new plug.
Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal. Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 5 A.

Protecting the environment

Separate collection. Products and batteries marked with this symbol must not be disposed of with normal household waste.

Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials. Please recycle electrical products and batteries according to local provisions. Further information is available at www.2helpU.com

Technical data

		KA450 (Type 1)
Input voltage	Vac	230
Power input	W 220
Orbits (no load) min	-1	16,000
Oscillations (no load)	min-1	32,000
Weight kg		1.22

Level of sound pressure according to EN 62841:

LpA (sound pressure) 85 dB(A), Uncertainty (K) 3 dB(A)

LWA (sound power) 96 dB(A), Uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to EN 62841:

Vibration emission value (a.) 8.3 m/s2, uncertainty (K) 1.5 m/s2

EC declaration of conformity

MACHINERY DIRECTIVE

KA450 Quarter Sheet Sander

Black & Decker declares that these products described under "technical data" are in compliance with: EN62841-1:2015, EN62841-2-4:2014.

These products also comply with directive 2006/42/EC, 2014/30/EU and 2011/65/EU.

For more information, please contact Black & Decker at the following address or refer to the back of the manual.

ENGLISH

(Original instructions)

The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of Black & Decker.

A.P. Smith

Technical Director

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

14/03/2019

Guarantee

Black & Decker is confident of the quality of its products and offers consumers a 24 month guarantee from the date of purchase. This guarantee is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.

To claim on the guarantee, the claim must be in accordance with Black & Decker Terms and Conditions and you will need to submit proof of purchase to the seller or an authorised repair agent. Terms and conditions of the Black & Decker 2 year guarantee and the location of your nearest authorised repair agent can be obtained on the Internet at www.2helpU.com, or by contacting your local Black & Decker office at the address indicated in this manual.

Please visit our website www.blackanddecker.co.uk to register your new Black & Decker product and receive updates on new products and special offers.

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

This sander is equipped with a switch that allows you to lock it on for extended use, and lock off to prevent accidental actuation.

Verrou sur (Fig. C)

Black & Decker Europe, 210 Bath Road, Slough, Berkshire, SL1 3YD

A.P.Smith Technical Director

Black & Decker Europe, 210 Bath Road, Slough, Berkshire, SL1 3YD Regno Unito 14/03/2019

Garanzia

Lock on/lock off slider

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

Verenigd Koninklijk

14/03/2019

Garantie

Hold the sander as shown in Figure C and squeeze so the paddle (1) depresses without putting pressure on the workpiece.
To turn the tool off, release the paddle.

Operación

Black & Decker Europa, 210 Bath Road, Slough,

Berkshire, SL1 3YD

Reino Unido

14/03/2019

Garantía

Director de Engenharia

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

Reino Unido

14/03/2019

Garantia

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

Storbritannien

14/03/2019

Garanti

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

Storbritannia

14/03/2019

Garanti

Black & Decker er trygg på kvaliteten av produitene sine og tilbyr en 24 maneders garanti fra kjopsdato. Denne garantierklæringenkommen i tillegg til dine lovbestemte rettigheter og er ikke i konflikt medppe. Garantien er gyldig innen områdene tilhorende medlemslandene i den Europeiske Union (EU) og det Europeiske Frihandelsområdet (EFTA).

For à ta garantien i bruk mä kravet vare i samsvar med kjøpsbetingelsene fra Black & Decker og du mà vise kjøpskvittering til forhandleren ell er til et autorisert serviceverksted. Betingelsene for Black & Deckers 2 árs garanti og adressen til din nærmeste autoriserte serviceverksted kan du finne på internett under www.2helpU.com, eller ved à kontakte ditt lokale Black & Decker kontor, adressen er angitt i dette bra克斯anvisningen.

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

Storbritannien

14/03/2019

Garanti

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD, Iso-Britannia

14/03/2019

Takuu

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

14/03/2019

Eyyúnón

H Black & Decker éivai σiyoupn yia tvn tiotnta twv
Tpoiovtw tnc kai Tpooqpei OTouc katavaawtec eyyunon
24 unvw aTIO tvn nuepounvia ayopac. Aut n eyyunon
ouuipnpwei kai ME Kaveva TpOIO SEV TapaBAtTEI
ta vouipa dikaiupata oac. H eyyunon IOxuei Evtoc ts
ETIKpateia cTwv xwpwveeaw TcEupwntaikc 'Evwoqn kai
tnc Eupwntaikc Zwvn EAEUthetaPWvSigmaalaywv.

Tia va uTIObaTe aIomega baoi TnC EyyunOng, n aIomega tha
TpiTe i va eivai ouuovn me touc Opuoc kai TpouTTotheeic
tns Black & Decker kai 0xpeiaotei va uTObaTe atio6eIg
ayopac otov TTwntn n oe EGOUIOBDOTnevo AVITIPPOoWTO
oepbc. MTopeite va aTOKTneTe Touc Opuoc kai TpouTTOeoeic tnc EyyunOnc 2 Etuv TnCS Black & Decker kai va
muTe tvtioeia Tou pAnoiotepou EGOUIOBDOTnevou
avTITPOoWtou ETIOKEuw vto Internet oTo www.2helpU.com,
nETIKoivwuvvTAC ME TO TOTIKO ac ypaefio Black & Decker
OTN dieuovon TPO uTOOBEKVUEta OTn PApov EYxepidio.

Napakaloume EIOKEeEITE TnV IOTOeIIDA paC www.blackanddecker.gr yia va kataxwpioTe To VEO aC TPoiov Black & Decker kai yia va evnuepwoTe yia Ta vea TPoiovta kai TiC EIIDIKc TPOOOPcS.

België/Belgique/Luxembourg Stanley Black & Decker Belgium BVBA Tel. NL [phone] www.blackanddecker.be Egide Walschaertsstraat 16 Tel. FR [phone] [e-mail] 2800 Mechelen Fax. [phone]
Danmark Black & Decker [e-mail] Roskildevej 22 www.blackanddecker.dk 2620 Albertslund
Deutschland www.blackanddecker.de [e-mail]	Stanley Black & Decker Deutschland GmbH Black & Decker Str. 40, D - 65510 Idstein	Tel. Fax	06126 21-0 06126 21-2980
Ελλάδαwww.blackanddecker.gr [e-mail]	Stanley Black & Decker (ΕλλΑΣ) E.I.E ΓΡΑΦΕΙΑ;Στράβωνος 7 & Βουλιαγμένης 166 74 Γλυφάδα - Αθήνα	Tηλ. Φαξ	210-8981616 210-8983570
SERVICE:	Ημερος Κότος 2-Xάνι Αδάμ 193 00 Αστρότιρούς - Αθήνα	Tηλ. Service Φαξ	210-8985208 210-5597598
Espana www.blackanddecker.es respuesta([e-mail]	Stanley Black & Decker Ibérica, S.C.A. Parc de Negocis "Mas Blau" Edificio Muntadas, c/Bergadá, 1, Of. A6 08820 El Prat de Llobregat (Barcelona)	Tel. Fax	934 797 400 934 797 419
France www.blackanddecker.fr	Black & Decker (France) S.A.S. 5 allée des Hétres B.P. 30084 69579 Limonest Cédex	Tel. Fax	04 72 20 39 20 04 72 20 39 00
Helvetia www.blackanddecker.ch [e-mail]	ROFO AG Gewerbezone Seeblick 3213 Kleinbosingen	Tel. Fax	026-6749393 026-6749394
Italia www.blackanddecker.it [e-mail]	Stanley Black & Decker Italia Via Energypark 6 20871 Vimercante (MB)	Tel. Fax	039-9590200 039-9590313 800-213935
Nederland www.blackanddecker.nl [e-mail]	Stanley Black & Decker Netherlands BV Holtum Noordweg 35, 6121 RE BORN Postbus 83, 6120 AB BORN	Tel. Fax	[phone] [phone]
Norge	Black & Decker [e-mail] Postboks 4613, Nydalen 0405 Oslo	www.blackanddecker.no
Österreich www.blackanddecker.at [e-mail]	Stanley Black & Decker Austria GmbH Oberlaerstraße 248, A-1230 Wien	Tel. Fax	01 66116-0 01 66116-614
Portugal www.blackanddecker.pt resposta([e-mail]	Black & Decker Limited SARL Quinta da Fonte - Edificio Q55 D. Diniz Rua dos Malhões, 2 e 2A - Piso 2 Esquerdo 2770 - 071 Paço de Arcos	Tel. Fax	214667500 214667580
Suomi	Black & Decker PL47 00521, Helsinki	[e-mail] www.blackanddecker.fi
Sverige	Black & Decker AB Box 94, 431 22 Möindal	[e-mail] www.blackanddecker.se
Türkije www.blackanddecker.com.tr	KALE Hırdağvat ve Makina AŞ. Defterdar Mah. Savaklar Cad. No:15 Edirnekapi / Eyüp / Istanbul 34050	Tel. Fax.	0212 533 52 55 0212 533 10 05
United Kingdom & Republic Of Ireland www.blackanddecker.co.uk [e-mail]	Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD	Tel. Fax	01753 511234 01753 512365
Middle East & Africa www.blackanddecker.eae [e-mail]	Black & Decker P.O.Box - 17164 Jebel Ali Free Zone (South), Dubai, UAE	Tel. Fax	[phone] [phone]