BLMH 362 - Lawn mower BlackLine - Free user manual and instructions
Find the device manual for free BLMH 362 BlackLine in PDF.
| Product type | Gasoline tiller (power hoe) |
| Brand | BlackLine |
| Model | BLMH 362 |
| Engine | 4-stroke, 140 cc, 2.2 kW (3 HP) |
| Working width | 36 cm |
| Working depth | Adjustable to 3 positions (depth stop) |
| Weight | 28 kg |
| Tank capacity | Approximately 2 liters |
| Fuel | Regular unleaded gasoline (E10) |
| Engine oil | Approximately 0.5 liter |
| Spark plug | F6RTC |
| Sound pressure level (LpA) | 71.81 dB(A) |
| Sound power level (LWA) | 93 dB(A) |
| Vibrations (ahv) | 7.66 m/s² (uncertainty K=1.5 m/s²) |
| Engine working speed | 3200 rpm |
| Starting system | Reversible starter (recoil starter) |
| Transmission | V-belt |
| Number of forward speeds | 1 |
| Oil sump capacity | Approximately 0.5 L |
| Blade material | Steel |
| Air filter maintenance | Clean or replace before each use |
| Spark plug maintenance | Check every 50 operating hours |
| Oil change | Perform with engine warm, approximately every 25 hours |
| Wear parts | Spark plug, air filter, tines, V-belt, fuel filter |
| Warranty | See conditions at the end of the manual |
Frequently Asked Questions - BLMH 362 BlackLine
User questions about BLMH 362 BlackLine
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Lawn mower in PDF format for free! Find your manual BLMH 362 - BlackLine and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. BLMH 362 by BlackLine.
USER MANUAL BLMH 362 BlackLine
Brandstof: Normale benzine Ioodvrij (E10)
Motorolie: ca.0,5 I
Tankinhoud: ca. 21
Vibratie a_hv .. 7,66 m/s
When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.
1. Safety regulations
The corresponding safety information can be found in the enclosed booklet.
Danger!
Read all safety regulations and instructions. Any errors made in following the safety regulations and instructions may result in an electric shock, fire and/or serious injury.
Keep all safety regulations and instructions in a safe place for future use.
Explanation of the symbols on the machine (Fig. 11):
1 Important! Read the operating instructions. Follow the warnings and safety instructions.
2 Important! Risk of injury from rotating parts. Keep your hands, feet and clothing away from these parts.
3 Always make sure that the machine is standing solidly whenever you leave it.
4 Important! Hot machine parts. Keep your distance.
5 Important! Switch off the engine before refueling.
6 Description of the clutch lever: 0 = Hoe blade "Stop; 1 = Hoe blade "On"
2. Layout and items supplied
2.1 Layout
- Engine / gear unit
2a. Reversing starter
2b. Fuel pump (primer) - Spark plug wrench
Assembly set for guard plate/transport wheel/handle (Fig. 3a/3b):
4a. Guard plate ()
4b.Bar
4c. 4x Screw M8x35 ()
5. Transport wheel ()
6. 4x Screw M8x20 ()
7. 4x Spring washer Ø8 ()
8. 4x Washer O8 ()
9. 1x Screw M10x65 ()
10. 1x Nut M10 ()
11. 1x Spring ()
12. 1x Split pin, small (*)
(*) not illustrated, already fitted
Assembly set for cultivator blades/depth stop (Fig. 4a):
13a. Cultivator blade, right ()
13b. Cultivator blade, left (^)
14. 2x Protective cap ()
15. Depth stop (^)
16. Split pin, large ()
17. 4x Screw M8x35 ()
18. 4x Washer 8 (*)
19. 4x Nut M8 (*)
(^*) not illustrated, already fitted
Assembly set for steering handle / clutch lever / start/stop lever (Fig. 5a/5b):
- Steering handle holder (*)
- Steering handle - clutch lever
- Steering handle - start/stop lever
- Cross strut
- Clutch lever
- Safety lever
- Start/stop lever
- 4x Screw M8x35
- 4x Nut M8
29.1x Screw M8x40 - 1x Cap nut M8
31.4x Screw M8x30 - 4x Washer large 08
33.4x Nut M8 - 4x Screw M8x20 (*)
GB
- 4x Spring washer Ø8 ()
36.4x Washer 08 () - 2x Cable clip
(^*) not illustrated, already fitted
2.2 Items supplied
Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.
- Open the packaging and take out the equipment with care.
- Remove the packaging material and any packaging and/or transportation braces (if available).
- Check to see if all items are supplied.
- Inspect the equipment and accessories for transport damage.
If possible, please keep the packaging until the end of the guarantee period.
Danger!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating!
- Original operating instructions
- Safetyinstructions
3. Proper use
The machine is designed for digging over beds and fi elds. Be sure to observe the restrictions in the additional safety instructions.
The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.
4. Technical data
Engine: 4-stroke engine, 140 ccm
Engine rating: 2.2 kW / (3) hp
Engine working speed: 3200 rpm
Working width: 36 cm
Hoe blade diameter: 26 cm
Forward gear: 1
Starting system: Reversing starter
Fuel: Regular unleaded petrol (E10)
Engine oil: approx. 0.5 l
Tank capacity: approx. 2
Vibration a. ..7.66 m/s
K uncertainty 1.5 m/s²
Weight: 28 kg
Spark plug: F6RTC
LpA sound pressure level 71.81 dB(A)
K uncertainty 1.5 dB
LWA sound power level 93 dB(A)
5. Before starting the equipment
Assembly set for guard plate/transport wheel/handle
- Arrange the components properly as described in section 2.1 Layout.
- Fit the handle (4b) as shown in Fig. 3b.
Assembling the cultivator blades and the depth stop
We recommend securing the depth stop in the middle position of the 3 possible positions when you begin your work. If you want to change the working depth, move the depth stop by sliding it up or down.
Assembling the steering handle, clutch lever and start/stop lever
- Arrange the components properly as described in section 2.1 Layout.
- Fit the steering handle clutch lever (21) and the steering handle start/stop lever (22) as shown in Fig. 5c.
- Fit the cross strut (23) as shown in Fig. 5d.
-
Fitting the clutch lever (24) is easy if you observe the following steps:
-
Push the Bowden wire sleeve (Fig. 5e/Item A) into the eyelet (Fig. 5e/Item B). Adjust the Bowden wire to maximum length by turning the lock nuts.
-
Attach the Bowden wire (Fig. 5f/Item C) to
GB
the clutch lever (24) and fit the clutch lever to the steering handle. Check that the safety lever is correctly seated. Carry out a function test. Pull the safety lever (25) to the clutch lever as shown in Fig. 6d. The clutch lever will be released and can be actuated.
- Adjust the length of the actuator cable as described in section 7.2.4.
- Fit the start/stop lever (26) as shown in Fig. 5g.
- Fit the cable clip (37) as shown in Fig. 5h.
Caution! You must fi II in engine oil and fuel before you start up for the first time.
- Check the fuel and engine oil levels and top up if required.
Make sure that the ignition cable is secured to the spark plug. - Check the area immediately around the power cultivator.
6. Operation
- Set the depth stop (Fig.4/Item 15) to the desired depth and secure with the split pin.
- Swing up the transport wheel and make sure that the bolt of the latch is engaged in the mount at the front (Fig. 6a-6b).
- You can adjust the steering handle to your physical size. To do so, undo the screws(Fig. 6c), adjust the bracket and retighten the screws.
To start the star-type hoes, pull up the safety lever (25) and press and hold down the clutch lever (24) (Fig.6d). Releasing the clutch lever will bring the star-type hoes to a stop (if they do not stop, readjust the clutch cable).
Starting the engine
- Ensure that the ignition cable is connected to the spark plug.
- Stand behind the power cultivator. Move the engine start/stop lever (Fig.7/Item 26) to position ON.
- Press the fuel pump (primer) (Fig. 1/Item 2b) 3 times. You can skip this point if the engine has already warmed up.
- Start the engine using the reversing starter (Fig. 1/Item 2a). To do this, pull out the handle by approx. 10 - 15cm until you feel a resistance) and then start the engine with a sharp tug.
Note! Never allow the actuator cable to snap back.
Note! In cold weather, it may be necessary to repeat the starting process several times.
Stopping the engine
Move the engine start/stop lever (26) into the STOP position.
7. Cleaning, maintenance, storage and ordering of spare parts
Danger!
Pull out the spark plug boot before doing any cleaning and maintenance work.
7.1 Cleaning
- Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
We recommend that you clean the device immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device.
7.2 Maintenance
Please note: Switch off the unit immediately and contact an authorized dealer:
In the event of unusual vibrations or noise.
If the engine appears to be overloaded or misfires.
7.2.1 Air filter maintenance
- Check and clean the air filter before every use, and replace it if necessary.
- Remove the filter element (Fig. 8a-8b).
- Do not use abrasive cleaning agents or petrol to clean the element.
Clean the element by tapping it on a flat surface. - Assemble in reverse order.
7.2.2 Spark plug maintenance
Check the spark plug for dirt and grime after 10 hours of operation and if necessary clean it with a copper wire brush. Thereafter service the spark
GB
plug after every 50 hours of operation.
Pull off the spark plug boot (Fig. 9) with a twist.
- Remove the spark plug (Fig. 9/Item D) with the supplied spark plug wrench.
- Assemble in reverse order.
7.2.3 Changing the oil and checking the oil level (before using the machine)
The motor oil is best changed when the motor is at working temperature.
Take out the dip stick (Fig. 10a / Item E).
And allow the warm oil to drain into a drip tray.
- Fill up with engine oil as far as the top mark on the dip stick (Fig. 10c/H).
- Important: Do not screw the dip stick when you check the oil level, simply insert it as far as the thread (H = Max. / L = Min.).
- Dispose of the waste oil properly.
7.2.4 Adjusting the Bowden wires
In the working setting it should be possible to push the clutch lever up to the push bar without this requiring much eff ort. If the Bowden wire is too taut for this, it must be extended. To do this, undo the lock nut opposite the main cable, extend the screw connector and then tighten the lock nut again (see Fig. 5e). If the star-type hoes no longer rotate then the screw connector will have to be shortened again (as described above).
7.2.5 Power cultivator gearing
The gear unit is driven by a V-belt. The gear unit can be repaired if this should become necessary. If repairs are necessary, please contact our customer service center.
7.3 Storage
Empty the fuel tank before you decommission the unit for a lengthy period of time. Clean the unit and coat all the metal parts with a thin fi lm of oil to prevent them rusting.
Store the unit in a clean, dry room.
7.4 Ordering replacement parts:
Please quote the following data when ordering replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
- Replacement part number of the part required
For our latest prices and information please go to www.isc-gmbh.info
GB
9. Troubleshooting guide
Warning: Switch off the engine and pull out the ignition cable before making any checks or adjustments.
Warning: If, after making an adjustment or repair to the engine, you let it run for a few minutes, remember that the exhaust and other parts will get hot. Do not touch these parts as these may burn you.
| Fault Possible causes Remedy | ||
| The unit does not operate smoothly and vibrates intenu-sively | - Bolts loose- Spark plug defective | - Check bolts- Replace spark plug |
| The engine does not start | - Spark plug defective- Fuel tank empty | - Replace spark plug- Top up fuel |
| Engine does not run smoothly | - Air fi liter dirty- Spark plug soiled or defective | - Clean the air fi liter- Clean or replace the spark plug |
| Drive power falls - Clutch play too large- V-belt loose | - Adjust clutch cable- Contact authorized customer ser-vice | |
| The engine will not start or dies after a short period of time | - Spark plug foul- No fuel | - Clean or replace spark plug- Top up fuel |
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the iSC GmbH.
Subject to technical changes
GB
10. EC Declaration of Conformity
Declaration of Conformity
We declare, that the product described is:
in Technical Data :
BLACKLINE
Petrol hoe BL-MH 36/2
Manufactured for:
is in conformity with the following directives:
Machinery Directive 2006/42/EC
EMC Directive 2014/30/EU
Emissions Directive 2016/1628
Emissions No.: e242016/16282018/989SYA1/P024200
Directive relating to the noise emission in the environment by equipment for use outdoors 2000/14/EC
(amended by Directive 2005/88 (EC)
and in accordance to the following applicable harmonized standards:
EN ISO 709+A4/AC:2012
EN ISO 14982-1:2009
The conformity with the Noise Emission of Outdoor
Equipment Directive is verified by the adherence to
the following emissions values:
Measured sound power level: 91.83 dB (A)
Guaranteed sound power level: 93 dB (A)
Notified Body:
TÜV Rheinland
LGA Products GmbH (0197)
Andreas Back
Head of Quality Management &
Person authorised to compile the technical file
We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.
| Category Example | |
| Wear parts* | Spark plug, air filter, cultivator blade, V-belt, coupling, fuel filter |
| Consumables* | |
| Missing parts |
- Not necessarily included in the scope of delivery!
In the effect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:
- Did the equipment work at all or was it defective from the beginning?
Did you notice anything (symptom or defect) prior to the failure? - What malfunction does the equipment have in your opinion (main symptom)? Describe this malfunction.
EH 01/2020 (01)
