SBCSC467-00C - Headphones PHILIPS - Free user manual and instructions

USER MANUAL SBCSC467-00C PHILIPS

Philips is dedicated to producing caring, reliable products that new moms and dads really need. Products whose reliability and operating quality bring reassurance. You can trust this Philips baby monitor to provide round-the-clock support by ensuring you can always hear your baby clearly, no matter where you are in the house.

Product illustration on inside flap:

A Baby unit

1 night light
2 talk button
3 loudspeaker
4 DC power supply socket
5 power button
6 power light
7 channel selection switch
8 microphone
9 AC power adapter
10 microphone sensitivity control
11 loudspeaker volume control
12 battery compartment cover

B Parent unit

13 sound-level lights
14 microphone
15 talk button
16 system check light
17 charging base
18 AC power adapter
19 power light
20 volume control - on/off switch
21 channel selection switch
22 loudspeaker
23 charging light
24 battery compartment cover
25 DC power supply socket
26 system check alarm switch

Important information

Please read this guide carefully before using the baby monitor, and keep it for future reference. This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.

• Make sure the Baby unit and adapter cable are always out of reach of the baby, at least one metre away.
• Never place the Baby unit inside the baby's bed or playpen!
• Never cover the baby monitor (with a towel, blanket, etc.).
• Clean the baby monitor with a damp cloth.
• Never use the baby monitor near water.

Your baby monitor

SBC SC467

Philips is dedicated to producing caring, reliable products that new moms and dads really need. Products whose reliability and operating quality bring reassurance. You can trust this Philips baby monitor to provide round-the-clock support by ensuring you can always hear your baby clearly, no matter where you are in the house.

Product illustration on inside flap:

A Baby unit

1 night light
2 talk button
3 loudspeaker
4 DC power supply socket
5 power button
6 power light
7 channel selection switch
8 microphone
9 AC power adapter

10 microphone sensitivity control
11 loudspeaker volume control
12 battery compartment cover

B Parent unit

13 sound-level lights
14 microphone
15 talk button
16 system check light
17 charging base
18 AC power adapter
19 power light
20 volume control - on/off switch
21 channel selection switch
22 loudspeaker
23 charging light
24 battery compartment cover
25 DC power supply socket
26 system check alarm switch

Important information

Please read this guide carefully before using the baby monitor, and keep it for future reference. This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.

• Make sure the Baby unit and adapter cable are always out of reach of the baby, at least one metre away.
• Never place the Baby unit inside the baby's bed or playpen!
• Never cover the baby monitor (with a towel, blanket, etc.).
• Clean the baby monitor with a damp cloth.
• Never use the baby monitor near water.

Getting your baby monitor ready

1 Position the Baby unit at least one metre away from your baby. Never place the baby unit inside the baby's bed or playpen.
2 Set channel selection switches to the same channel on both units.
3 Connect the power adapter to Baby unit socket.
4 Plug the power adapter into mains supply.
5 Move away from the Baby unit with the Parent unit. If units are positioned too close to each other then a high-pitched noise can be heard.
6 Connect the second power adapter to the Parent unit's charging base socket.
7 Plug the second power adapter into a mains supply.
8 Place the Parent unit inside its charging base.

The red charging light lights.

9 Leave the Parent unit in charging base for at least 14 hours to fully charge the batteries. When batteries are fully charged, the Parent unit can be used cordlessly for up to 12 hours.

10 Place the Parent unit inside the charging base when power light on the Parent unit flashes red (an indication that batteries are low).

Using your baby monitor

Listening to your baby

1 Push the power button on the Baby unit to turn it on.

The power light lights (green).
2 Adjust the microphone sensitivity of the Baby unit to a level you prefer (using your own voice as a sound reference).
The power light lights (yellow) when a sound is picked up.

3 Switch the Parent unit on and adjust the volume to level you prefer using the VOLUME ON/OFF control.

The digital SYSTEM CHECK light lights continuously (green) when the

Parent unit and Baby unit are in touch with each other.

Talking back to comfort your baby

1 Push the power button on the Baby unit to turn it on.

The power light lights (green).
2 Adjust the volume on the Baby unit to about mid-range using VOLUME control.
Later you can adjust the volume of baby unit's loudspeaker to a level you prefer.
3 Switch the Parent unit on and adjust the volume to the level you prefer using the VOLUME ON/OFF control.
4 On the Parent unit, press and hold the talk button and talk clearly into the microphone.

While the talk button on the Parent unit is being pressed, no sounds from the Baby unit can be heard on the loudspeaker of the Parent unit.

5 Release the talk button when finished.

Using the family intercom system

1 Push the power button on the Baby unit to turn it on.

The power light lights (green).
2 Adjust the volume on the Baby unit to about mid-range using the VOLUME control.
3 Set the sensitivity level on the Baby unit to zero.
4 Switch the Parent unit on and adjust the volume to the level you prefer using the VOLUME ON/OFF control.
5 On the Parent unit, press and hold the talk button and talk clearly into the microphone.
6 Release the talk button when you are finished.
7 On the Baby unit, press and hold the talk button and talk clearly into the microphone.

Release the talk button when you are finished.

While the talk button on either unit is being pressed, a signal from the other unit cannot be heard. In other words, only one person should speak at a time.

Features explanation

Avoiding interference

If there is interference or if sound reception is poor, switch both units to another channel.

Always make sure that the channel selection switches on both units are set to the same position.

Monitoring baby silently

Adjust the volume on the Parent unit to the lowest level using the VOLUME ON/OFF control (do not switch off).

the sound-level lights visually alert you to baby's sounds.

The more sound your baby makes, the more lights light.

Checking that the units are in touch

Check that the digital SYSTEM CHECK light on the Parent unit lights continuously (green) to confirm that the connection between both units is reliable.

If the light flashes (red), move the Parent unit closer to the Baby unit.

The light flashes if the units are out of range for more than 30 seconds or if there is interference.

Switching on the system check alarm

You can switch on the system check alarm on the Parent unit that beeps when the units are not in touch. The Parent unit is delivered with the system check alarm switched off.

1 Open the Parent unit's battery compartment cover.
2 Set the switch inside compartment to the ON position (
3 Close battery compartment cover.

The SYSTEM CHECK light can still flash even if the system check alarm is switched off.

Switching on the night light

Push the Baby unit night light to switch it on and off.

Switch off the night light when operating the Baby unit on batteries to conserve power.

Range 250 m in open air

The baby monitor has an operating range of up to 250 metres in ideal open-air conditions. This means that the units can see each other with no obstacles in between. Walls, ceilings, large objects and even glass affect the operating range. The more obstacles there are in between, the shorter the operating range.

Using batteries

Operating the Baby unit cordlessly

1 Remove the battery compartment cover using a coin.

2 Insert four I.5V, LR6 (AA) batteries noting the + and - configuration inside the battery compartment.

Batteries not included; we recommend non-chargeable Philips Alkaline batteries.

3 Put the cover back in place and secure using a coin.

If the power light flashes (red) install new batteries. The unit operates for up to 30 hours on batteries.

Replacing the Parent unit's battery pack

1 Open the Parent unit's battery compartment cover.
2 Disconnect the old battery pack from the power plug and remove.
3 Carefully connect the new battery pack to the power plug and place inside the battery compartment.
4 Close battery compartment cover.

Disposal of batteries

Dispose of used batteries in an environmentally friendly manner. Do not mix old and new batteries, or different types of batteries.

Remove Baby unit batteries if the baby monitor is not to be used for long periods.

Technical specifications

Power supply:

Operating range:

Operating temperature:

Digital Pilot tone:

Transmission frequencies:

• Battery pack; rechargeable NiMH for Parent unit (included);
• Optional batteries 4 × 1.5V ; AA alkaline for Baby unit (not included);
• AC power adapter 230V AC, 50 Hz (two included): - Output voltage 9V DC, 200mA.
• Only use the AC power adapter included or a type that complies with safety standard EN60950 and that has the following specification: input 230V AC, 50 Hz; output 9 Volt DC / 200mA.
  up to 250 metres in ideal conditions (walls, floors, etc. can limit this distance.)
  10°C to 40°C
• Continuous communication link (hidden signal helps reduce interference and ensures a continuous link between both units so you only hear your baby's sounds).

SBC SC467/00:

from 40.695 to 40.675 MHz

SBC SC467/05 (IRE, UK):

from 49.830 to 40.890 MHz

SBC SC467/16 (ES):

from 31.000 to 31.350 MHz

Problem solving
Problem	Possible cause	Solution
Power light does not light.	Parent unit: unit is not turned on.	Turn VOLUME ON/OFF control downwards.
	Batteries are low.	Recharge batteries.
	Baby unit: unit is not turned on.	Push power button.
	Power adapter is not plugged in or batteries are exhausted.	Plug in power adapter or replace batteries.
High pitched noise.	Units are too close together.	Move parent unit away from baby unit. Turn VOLUME ON/OFF control on parent unit upwards.
Parent unit batteries do not charge.	Battery life is at an end.	Connect charging base to mains power. Replace battery pack.
No sound.	Volume on parent unit is set too low.	Turn VOLUME ON/OFF control downwards.
Power light flashing.	Batteries are low or empty.	Parent unit:- recharge battery pack. Baby unit:- replace batteries or connect to mains power.
Talk-back not working*.	Loudspeaker volume on Baby unit is too low.	Set VOLUME control on baby unit to mid-range.
Intercom function not working.	Sensitivity setting on Baby unit still on.	Set sensitivity on Baby unit to zero.
Interference or poor reception.	Mobile or cordless phones too close to the baby monitor.	Move phones away from the units.
Pick-up from another baby monitor.	Both systems are operating on the same frequency.	Switch channels.
System check light flashing (red) / System check alarm.	Units are out of range or there is interference from another FM source.	Move units closer together to restore the link. Remove the other FM source.

• With the talk / intercom function if either the parent or baby unit is transmitting, then the other unit can only receive and not transmit.

Votre babyphone

SBC SC467

SBC SC467/05 (IR, RU):

Alcance de operation:

NOS V A ETOIUMAOTE TO baby monitor OAC

1 Toothehote Tn Movad wopoulaayiotov evaetpoakpi ao to wopoc. Mn baTe Tne Movad wopoueosto kpebatou wopou n to npko tou.
2 P0θμiσTEouc diakóπεεπλoγηκαvauiou σto iδo kaváλι κaσιδο μováδε.
3 Suovdeste tvn psoaapoyea ioxioe stny npia ng Movadac mwpo.
4 Suovdeoge tvpooapoyoeioxoc styn apoxn peuatoq.
5 Anouakpvvthe ano tn Movad8a mwpov exovtac aoc ts Movad8a yoviob. Av o1 movadcs eivai noo kovta n ma stnv alan, npoei va akovotei evac ocos.
6 Evodote to deutepo nposapuoyea ioxbos otyn pica ts faonc opotionns Movadac yoviou.
7 SuovdeoTe to devtepo npospaupoyeaioxbooc eia npoxnpeuato
8 Toothehtote Tn Movadayoviou maos stn bao npoptiog. >To kokkivo qos opptiog ava
9 ApnoTe Tn Movada yovioo stn Baoon fopotionc epi 14 toulaixotov ope c yua va optiote n npoc ts matapiecs. Otav o i npataies eivai npoc ofoptioeves, n Movada yoviou upoei va xnpouoountheta xomegaupx12 opec.
10ToothetaiotEtnMoVadagoviovu eoa stn Baoon foprtioe otav to ooc ioovc stn Movadogoviovauvaosnvkeokkivo (evdeicn otoi pataipie civai xunlae).

Product illustration on inside flap:

A Baby-unit

Overforghingsfrekvenser:

Product illustration on inside flap:

A Lapsen yksikkö