STRDH750 - Receiver SONY - Free user manual and instructions

USER MANUAL STRDH750 SONY

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To reduce the risk of fire, do not cover the ventilation opening of the appliance with newspapers, tablecloths, curtains, etc. Do not expose the appliance to naked flame sources (for example, lighted candles). To reduce the risk of fire or electric shock, do not expose this appliance to dripping or splashing, and do not place objects filled with liquids, such as vases, on the appliance. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Do not expose batteries or appliances with battery-installed to excessive heat, such as sunshine and fire. The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. Excessive sound pressure from earphones and headphones can cause hearing loss. This symbol is intended to alert the user to the presence of the Hot Surface that may be hot if it is touched during the normal operation. This equipment has been tested and found to comply with the limits set out in the EMC Directive using a connection cable shorter than 3 meters. For the customers in Europe Disposal of waste batteries and electrical and electronic equipment (applicable in the European Union and other European countries with separate collection systems) This symbol on the product, the battery or on the packaging indicates that the product and the battery shall not be treated as household waste. On certain batteries this symbol might be used in combination with a chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are added if the battery contains more than 0.0005% mercury or 0.004% lead. By ensuring these products and batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery and the electrical and electronic equipment will be treated properly, hand over these products at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product or battery. WARNING3

Notice for customers: The following information is only applicable to equipment sold in countries applying EU Directives. This product has been manufactured by or on behalf of Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. Inquiries related to product compliance based on European Union legislation shall be addressed to the authorized representative, Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters, please refer to the addresses provided in the separate service or guarantee documents. Hereby, Sony Corp., declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For details, please access the following URL: http://www.compliance.sony.de/ This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System.

• Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, Surround EX, and the double-D symbol are trademarks of Dolby Laboratories. ** For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS-HD Master Audio is a trademark of DTS, Inc. © DTS, Inc. All Rights Reserved. This receiver incorporates High-Definition Multimedia Interface (HDMI

) technology. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. All other trademarks and registered trademarks are of their respective holders. In this manual, ™ and ® marks are not specified. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance. Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary. MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson. “x.v.Color (x.v.Colour)” and “x.v.Color (x.v.Colour)” logo are trademarks of Sony Corporation. “BRAVIA” is a trademark of Sony Corporation. On copyrights4

“PlayStation” is a registered trademark of Sony Computer Entertainment Inc. “WALKMAN” and “WALKMAN” logo are registered trademarks of Sony Corporation. MICROVAULT is a trademark of Sony Corporation. MHL, Mobile High-Definition Link and the MHL Logo are trademarks or registered trademarks of MHL Licensing, LLC. The Bluetooth

word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners. © 2013 CSR plc and its group companies. The aptX

mark and the aptX logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions. The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. Android™ is a trademark of Google Inc. Google Play™ is a trademark of Google Inc. Precautions On safety Should any solid object or liquid fall into the cabinet, unplug the receiver and have it checked by qualified personnel before operating it any further. On power sources

• Before operating the receiver, check that the operating voltage is identical with your local power supply. The operating voltage is indicated on the nameplate on the back of the receiver.

• The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

• If you are not going to use the receiver for a long time, be sure to disconnect the receiver from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord.

• The AC power cord (mains lead) must be changed only at a qualified service shop. On heat buildup Although the receiver heats up during operation, this is not a malfunction. If you continuously use this receiver at a large volume, the cabinet temperature of the top, side and bottom rises considerably. To avoid burning yourself, do not touch the cabinet. On placement

• Place the receiver in a location with adequate ventilation to prevent heat buildup and prolong the life of the receiver.

• Do not place the receiver near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock.

• Do not place anything on top of the cabinet that might block the ventilation holes and cause malfunctions.

• Do not place the receiver near equipment such as a TV, VCR, or tape deck. (If the receiver is being used in combination with a TV, VCR, or tape deck, and is placed too close to that equipment, noise may result, and picture quality may suffer. This is especially likely when using an indoor antenna (aerial). Therefore, we recommend using an outdoor antenna (aerial).)

• Use caution when placing the receiver on surfaces that have been specially treated (with wax, oil, polish, etc.) as staining or discoloration of the surface may result.5

On operation Before connecting other equipment, be sure to turn off and unplug the receiver. On cleaning Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. On Bluetooth communication

• Bluetooth devices should be used within approximately 10 meters (unobstructed distance) of each other. The effective communication range may become shorter under the following conditions. – When a person, metal object, wall or other obstruction is between the devices with a Bluetooth connection – Locations where a wireless LAN is installed – Around microwave ovens that are in use – Locations where other electromagnetic waves occur

• Bluetooth devices and wireless LAN (IEEE 802.11b/g) use the same frequency band (2.4 GHz). When using your Bluetooth device near a device with wireless LAN capability, electromagnetic interference may occur. This could result in lower data transfer rates, noise, or inability to connect. If this happens, try the following remedies: – Use this receiver at least 10 meters away from the wireless LAN device. – Turn off the power to the wireless LAN equipment when using your Bluetooth device within 10 meters. – Install this receiver and Bluetooth device as closer to each other as possible.

• The radio waves broadcast by this receiver may interfere with the operation of some medical devices. Since this interference may result in malfunction, always turn off the power on this receiver and Bluetooth device in the following locations: – In hospitals, on trains, in airplanes, at gas stations, and any place where flammable gasses may be present – Near automatic doors or fire alarms

• This receiver supports security functions that comply with the Bluetooth specification to ensure secure connection during communication using Bluetooth technology. However, this security may be insufficient depending on the setting contents and other factors, so always be careful when performing communication using Bluetooth technology.

• Sony cannot be held liable in any way for damages or other loss resulting from information leaks during communication using Bluetooth technology.

• Bluetooth communication is not necessarily guaranteed with all Bluetooth devices that have the same profile as this receiver.

• Bluetooth devices connected with this receiver must comply with the Bluetooth specification prescribed by the Bluetooth SIG, Inc., and must be certified to comply. However, even when a device complies with the Bluetooth specification, there may be cases where the characteristics or specifications of the Bluetooth device make it impossible to connect, or may result in different control methods, display or operation.

• Noise may occur or the audio may cut off depending on the Bluetooth device connected with this receiver, the communications environment, or surrounding conditions. If you have any questions or problems concerning your receiver, please consult your nearest Sony dealer.6

(6 ohms, 20 Hz – 20 kHz, THD 0.09%) 90 W + 90 W Stereo Mode Output Power

(6 ohms, 1 kHz, THD 1%) 105 W + 105 W Surround Mode Output Power 1)2) (6 ohms, 1 kHz, THD 0.9%) 145 W per channel

Measured under the following conditions: Power requirements: 230 V AC, 50 Hz

Reference power output for front, center, surround, surround back and front high speakers. Depending on the sound field settings and the source, there may be no sound output. Frequency response Analog 10 Hz – 100 kHz, +0.5/–2 dB (with sound field and equalizer bypassed) Input Analog Sensitivity: 500 mV/50 kilohms S/N

Digital (Coaxial) Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LPF) Digital (Optical) S/N: 100 dB (A, 20 kHz LPF) Output (Analog) SUBWOOFER Voltage: 2 V/1 kilohm Equalizer Gain levels ±10 dB, 1 dB step

INPUT SHORT (with sound field and equalizer bypassed).

Weighted network, input level. FM tuner section Tuning range

87.5 MHz – 108.0 MHz

Antenna (aerial) FM wire antenna (aerial) Antenna (aerial) terminals 75 ohms, unbalanced AM tuner section Tuning range 531 kHz – 1,602 kHz (9 kHz step) Antenna (aerial) Loop antenna (aerial) Video section Inputs/Outputs Video: 1 Vp-p, 75 ohms7

Supports YUV 4:2:0 / 8 bit format only.

Supports 8 bit format only.

These formats are also supported by an MHL connection. MHL section Supported MHL version Incorporates MHL 2 Maximum current 900 mA Format 2D

1920 × 1080p @ 59.94/60 Hz a – aa 1920 × 1080p @ 50 Hz a – aa 1920 × 1080p @ 29.97/30 Hz a

1920 × 1080p @ 25 Hz a

1920 × 1080i @ 59.94/60 Hz a

1280 × 720p @ 59.94/60 Hz a

1280 × 720p @ 50 Hz a

USB works with iPhone 5s, iPhone 5c, iPhone 5, iPhone 4s, iPhone 4, iPhone 3GS, iPhone 3G, iPod touch (2nd through 5th generation), iPod classic, and iPod nano (3rd through 7th generation). Bluetooth technology works with iPhone 5s, iPhone 5c, iPhone 5, iPhone 4s, iPhone 4, iPhone 3GS, and iPod touch (4th and 5th generation). You can use “SongPal” app with this receiver via Bluetooth. USB section Supported format* MP3 (MPEG 1 Audio Layer-3): 32 kbps – 320 kbps, VBR WMA: 48 kbps – 192 kbps AAC: 48 kbps – 320 kbps WAV: 8 kHz – 48 kHz, 16 bit PCM

• Compatibility with all encoding/writing software, recording devices and recording media cannot be guaranteed. Supported USB device Mass Storage Class Maximum current 500 mA Bluetooth section Communication system Bluetooth Specification version 3.0 Output Bluetooth Specification Power Class 2 Maximum communication range Line of sight approx. 10 m

A2DP (Advanced Audio Distribution Profile) AVRCP 1.3 (Audio Video Remote Control Profile) Supported Codecs

The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, cordless phone, reception sensitivity, antenna’s performance, operating system, software application, etc.

Bluetooth standard profiles indicate the purpose of Bluetooth communication between devices.

Codec: Audio signal compression and conversion format

General Power requirements 230 VAC, 50/60 Hz Power consumption 240 W Power consumption (during standby mode)

0.3 W (When [Control for HDMI], [Pass

Through] and [Bluetooth Standby] are set to [Off].)

0.5 W (When [Control for HDMI] and

[Bluetooth Standby] are set to [On], [Pass Through] is set to [Off].) Dimensions (width/height/depth) (Approx.) 430 mm × 156 mm × 329.4 mm including projecting parts and controls Mass (Approx.)

Design and specifications are subject to change without notice.2

1920 × 1080p @ 25 Hz a

1920 × 1080p @ 23,98/24 Hz a

1280 × 720p @ 50 Hz a

1280 × 720p @ 23,98/24 Hz a

1920 × 1080p @ 25 Hz a

1920 × 1080p @ 23,98/24 Hz a

1280 × 720p @ 50 Hz a

1280 × 720p @ 23,98/24 Hz a

1920 × 1080p @ 25 Hz a

1920 × 1080p @ 23,98/24 Hz a

1280 × 720p @ 50 Hz a

1280 × 720p @ 23,98/24 Hz a

1920 × 1080p @ 25 Hz a

1920 × 1080p @ 23,98/24 Hz a

1280 × 720p @ 50 Hz a

1280 × 720p @ 23,98/24 Hz a

1920 × 1080p @ 25 Hz a

1920 × 1080p @ 23,98/24 Hz a

1280 × 720p @ 50 Hz a

1280 × 720p @ 23,98/24 Hz a