F 500 - Heating Jøtul - Free user manual and instructions

Product type	Wood stove
Brand	Jøtul
Model	F 500
Material	Cast iron
Surface treatment	Black paint and enamel
Fuel	Wood only
Nominal heat output	8,5 kW
Efficiency	78%
Weight	200 kg
Maximum log length	55 cm
Flue connection diameter	∅150 mm
Recommended draft	10 Pa
Flue gas temperature	285 °C
CO rate (at 13% O₂)	0.10 %
Air inlets	Upper and lower
Operating mode	Intermittent (batch combustion)
Hourly wood consumption (nominal)	Approximately 2.7 kg/h
Flue gas mass flow	8.0 g/s
Floor protection	Integrated heat shield, minimum metal plate 0.9 mm
Optional equipment	External ventilation duct (ref. 221031), rear heat shield (ref. 350956)
Periodic maintenance	Replacement of deflector, lining plates, and refractory bricks
Spare parts	Use only genuine Jøtul parts
Serial number	Referenced on product label, to be mentioned when contacting

Frequently Asked Questions - F 500 Jøtul

What type of wood to use with the Jøtul F 500?

Use exclusively dry wood (< 20% humidity). Recommended log length: 30-55 cm for kindling and about 30 cm for firewood. Diameter: 2-5 cm for kindling, 8-13 cm for split wood.

What is the nominal heat output of the Jøtul F 500?

The nominal heat output is 8.5 kW, with an efficiency of 78%. It is achieved with an air opening of about 50%.

How to install the stove on a wooden floor?

The stove is equipped with a heat shield under the base. You can place it directly on a wooden floor provided it is covered with a metal plate or non-combustible material of minimum thickness 0.9 mm. Remove any combustible covering (linoleum, carpet) under the plate.

What are the safety distances to combustible walls?

Refer to diagram figure 1 in the manual. Minimum distances vary by configuration. Generally, maintain at least 1200 mm to a combustible ceiling. An optional rear heat shield allows reducing distances.

How to adjust the air supply?

The air inlet is controlled by a button under the door: position left = closed, position right = open. Adjust to control combustion.

Is a specific draft required for the flue?

The recommended draft is 10 Pa. If the draft is too strong, install a draft damper. The chimney cross-section must be at least equal to that of the flue (177 cm²).

How to maintain the vermiculite deflector?

The deflector is a vermiculite plate located on the secondary combustion tubes. To replace it, carefully remove it and replace it by applying refractory cement at the back. Avoid impacts as vermiculite is fragile.

Can an external air duct be connected?

Yes, with the external ventilation duct option (ref. 221031). Connect a flexible hose ∅80 mm to the air inlet located under the rear of the appliance, then to the external fresh air intake.

How to empty the ash pan?

Open the ash pan door by turning the knob half a turn counterclockwise. Grasp the handle with a glove and empty the ashes. Always leave a layer of ashes to protect the bottom and facilitate restarting.

What to do in case of malfunction?

Refer to the Malfunctions – Causes and Troubleshooting section of the general use and maintenance manual. If the problem persists, contact your dealer or Jøtul, mentioning the appliance's serial number.

USER MANUAL F 500 Jøtul

GB - Installation manual with technical data 11

Exterior view of a vintage wood-paneled gas stove with arched windows and flames (no text or symbols visible)

Jetul produkter/ Jetul's products MAYLLE - canadatihur- og kreditinjärkem 12 - jetuläkem (kreding, 100 mmol/mol) - canadat 13 - kreditinjärkem (kreding, 100 mmol/mol) 14 - kreditinjärkem (kreding, 100 mmol/mol) 15 - kreditinjärkem (kreding, 100 mmol/mol) 16 - kreditinjärkem (kreding, 100 mmol/mol) 17 - kreditinjärkem (kreding, 100 mmol/mol) 18 - kreditinjärkem (kreding, 100 mmol/mol) 19 - kreditinjärkem (kreding, 100 mmol/mol) 20 - kreditinjärkem (kreding, 100 mmol/mol) 21 - kreditinjärkem (kreding, 100 mmol/mol) 22 - kreditinjärkem (kreding, 100 mmol/mol) 23 - kreditinjärkem (kreding, 100 mmol/mol) 24 - kreditinjärkem (kreding, 100 mmol/mol) 25 - kreditinjärkem (kreding, 100 mmol/mol) 26 - kreditinjärkem (kreding, 100 mmol/mol) 27 - kreditinjärkem (kreding, 100 mmol/mol) 28 - kreditinjärkem (kreding, 100 mmol/mol) 29 - kreditinjärkem (kreding, 100 mmol/mol) 30 - kreditinjärkem (kreding, 100 mmol/mol) 31 - kreditinjärkem (kreding, 100 mmol/mol) 32 - kreditinjärkem (kreding, 100 mmol/mol) 33 - kreditinjärkem (kreding, 100 mmol/mol) 34 - kreditinjärkem (kreding, 100 mmol/mol) 35 - kreditinjärkem (kreding, 100 mmol/mol) 36 - kreditinjärkem (kreding, 100 mmol/mol) 37 - kreditinjärkem (kreding, 100 mmol/mol) 38 - kreditinjärkem (kreding, 100 mmol/mol) 39 - kreditinjärkem (kreding, 100 mmol/mol) 40 - kreditinjärkem (kreding, 100 mmol/mol) 41 - kreditinjärkem (kreding, 100 mmol/mol) 42 - kreditinjärkem (kreding, 100 mmol/mol) 43 - kreditinjärkem (kreding, 100 mmol/mol) 44 - kreditinjärkem (kreding, 100 mmol/mol) 45 - kreditinjärkem (kreding, 100 mmol/mol) 46 - kreditinjärkem (kreding, 100 mmol/mol) 47 - kreditinjärkem (kreding, 100 mmol/mol) 48 - kreditinjärkem (kreding, 100 mmol/mol) 49 - kreditinjärkem (kreding, 100 mmol/mol) 50 - kreditinjärkem (kreding, 100 mmol/mol) 51 - kreditinjärkem (kreding, 100 mmol/mol) 52 - kreditinjärkem (kreding, 100 mmol/mol) 53 - kreditinjärkem (kreding, 100 mmol/mol) 54 - kreditinjärkem (kreding, 100 mmol/mol) 55 - kreditinjärkem (kreding, 100 mmol/mol) 56 - kreditinjärkem (kreding, 100 mmol/mol) 57 - kreditinjärkem (kreding, 100 mmol/mol) 58 - kreditinjärkem (kreding, 100 mmol/mol) 59 - kreditinjärkem (kreding, 100 mmol/mol) 60 - kreditinjärkem (kreding, 100 mmol/mol) 61 - kreditinjärkem (kreding, 100 mmol/mol) 62 - kreditinjärkem (kreding, 100 mmol/mol) 63 - kreditinjärkem (kreding, 100 mmol/mol) 64 - kreditinjärkem (kreding, 100 mmol/mol) 65 - kreditinjärkem (kreding, 100 mmol/mol) 66 - kreditinjärkem (kreding, 100 mmol/mol) 67 - kreditinjärkem (kreding, 100 mmol/mol) 68 - kreditinjärkem (kreding, 100 mmol/mol) 69 - kreditinjärkem (kreding, 100 mmol/mol) 70 - kreditinjärkem (kreding, 100 mmol/mol) 71 - kreditinjärkem (kreding, 100 mmol/mol) 72 - kreditinjärkem (kreding, 100 mmol/mol) 73 - kreditinjärkem (kreding, 100 mmol/mol) 74 - kreditinjärkem (kreding, 100 mmol/mol) 75 - kreditinjärkem (kreding, 100 mmol/mol) 76 - kreditinjärkem (kreding, 100 mmol/mol) 77 - kreditinjärkem (kreding, 100 mmol/mol) 78 - kreditinjärkem (kreding, 100 mmol/mol) 79 - kreditinjärkem (kreding, 100 mmol/mol) 80 - kreditinjärkem (kreding, 100 mmol/mol) 81 - kreditinjärkem (kreding, 100 mmol/mol) 82 - kreditinjärkem (kreding, 100 mmol/mol) 83 - kreditinjärkem (kreding, 100 mmol/mol) 84 - kreditinjärkem (kreding, 100 mmol/mol) 85 - kreditinjärkem (kreding, 100 mmol/mol) 86 - kreditinjärkem (kreding, 100 mmol/mol) 87 - kreditinjärkem (kreding, 100 mmol/mol) 88 - kreditinjärkem (kreding, 100 mmol/mol) 89 - kreditinjärkem (kreding, 100 mmol/mol) 90 - kreditinjärkem (kreding, 100 mmol/mol) 91 - kreditinjärkem (kreding, 100 mmol/mol) 92 - kreditinjärkem (kreding, 100 mmol/mol) 93 - kreditinjärkem (kreding, 100 mmol/mol) 94 - kreditinjärkem (kreding, 100 mmol/mol) 95 - kreditinjärkem (kreding, 100 mmol/mol) 96 - kreditinjärkem (kreding, 100 mmol/mol) 97 - kreditinjärkem (kreding, 100 mmol/mol) 98 - kreditinjärkem (kreding, 100 mmol/mol) 99 - kreditinjärkem (kreding, 100 mmol/mol) 100 - kreditinjärke * KREDIT INJALO PRODUKTEN * KREDIT INJALO PRODUKTEN * KREDIT INJALO PRODUKTEN * KREDIT INJALO PRODUKTEN * KREDIT INJALO PRODUKTEN * KREDIT INJALO PRODUKTEN * KREDIT INJALO PRODUKTEN * KREDIT INJALO PRODUKTEN * KREDIT INJALO PRODUKTEN * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KEDUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT * KESUT KESUT

GB - Before use, please read "General use and maintenance manual" carefully.

Fiatum Jedal Tazem tatalie (notional) local Standard Citation in accordance to applicable standards table. Worner, M. 1962, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025, 2026, 2027, 2028, 2029, 2030, 2031, 2032, 2033, 2034, 2035, 2036, 2037, 2038, 2039, 2040, 2041, 2042, 2043, 2044, 2045, 2046, 2047, 2048, 2049, 2050, 2051, 2052, 2053, 2054, 2055, 2056, 2057, 2058, 2059, 2060, 2061, 2062, 2063, 2064, 2065, 2066, 2067, 2068, 2069, 2070, 2071, 2072, 2073, 2074, 2075, 2076, 2077, 2078, 2079, 2080, 2081, 2082, 2083, 2084, 2085, 2086, 2087, 2088, 2089, 2090, 2091, 2092, 2093, 2094, 2095, 2096, 2097, 2098, 2099, 2100, 2101, 2102, 2103, 2104, 2105, 2106, 2107, 2108, 2109, 2110, 2111, 2112, 2113, 2114, 2115, 2116, 2117, 2118, 2119, 2120, 2121, 2122, 2123, 2124, 2125, 2126, 2127, 2128, 2129, 2130, 2131, 2132, 2133, 2134, 2135, 2136, 2137, 2138, 2139, 2140, 2141, 2142, 2143, 2144, 2145, 2146, 2147, 2148, 2149, 2150, Specialty: Qualification: Con-ficial boundaries: Approved by: Macyo: Standard Santel: M.A. x- Specialty: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A . x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normalty: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.C. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Normality: M.A. x- Neutrality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Neutrality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- Normality: x- normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty normalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalty naturalt y. Year. Dec. (Year). Dec. (Year). Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Normalities: Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital :\nTotal number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's capital : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's year : Total number of employees in the company's year : Total number of employees in the company's year : Total number of employees in the company's year : Total number of employees in the company's year : Total number of employees in the company's year : Total number of employees in the company's year : Total number of employees in the company's year : Total number of employees in the company's year : Total number of employees in the company's year : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annually : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's annual : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's total : Total number of employees in the company's full : Total number of employees in the company's full : Total number of employees in the company's full : Total number of employees in the company's full : Total number of employees in the company's full : Total number of employees in the company's full : Total number of employees in the company's full : Total number of employees in the company's full : Total number of employees in the company's full : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total number of workers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Total numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Tonal numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Toral numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Tocal numbers : Toral values for a year. Dec. (Year). Number categories: Average value per unit (except per unit) Average value per unit (except per unit) Average value per unit (except per unit) Average value per unit (except per unit) Average value per unit (except per unit) Average value per unit (except per unit) Average value per unit (except per unit) Average value per unit (except per unit) Average value per unit (except per unit) Average value per unit (except per unit) Average value per unit (except per unit) Average value per unit (except per unit) A normal distribution is normalized by a standard deviation from a normal distribution. The average distribution is normalized by a standard deviation from a normal distribution. The average distribution is normalized by a standard deviation from a normal distribution. The average distribution is normalized by a standard deviation from a normal distribution. The average distribution is normalized by a standard deviation from a normal distribution. The average distribution is normalized by a standard deviation from a normal distribution.

3.5 Montering innan installation

Total Room heater, Funding cost fuel Industrial Ministry in accordance to subject common standards. Name of the company's general and administrative department. In use of 20% Concentration and each gains for employees. Ministry of the company. Offshore Equipment charges All rights Agriculture & Aggs. The appliance can be used in a shared file. Country Consultation Contributions Approved by Mitaray Washan Santos Chak P P1 Sontages from research Research on the R& P2 Sweden National Holding and Research and other Follow our instructions. Use only commercialized fees. Worings and Bedingungsbeding business. Weferred to our respective business owners. Expensed for construction and distribution. Utilisation of property in commercialities recommended. Total No. 7 years Year 2004 Manufacturing Iqbal AS POB 14-11 No 2602 Pudifikstad Montney

Installation manual with technical data

1.0 Relationship to the authorities .....11

2.0 Technical data ....11

3.0 Installation 12

4.0 Service 13

5.0 Optional equipment 13

Figures/ Pictures 32

General use and maintenance manual

6.0 Safety precautions

7.0 Choice of fuel

8.0 Use

9.0 Maintenance

10.0 Operational problems - troubleshooting

On all our products there is a label indicating the serial number and year. Write this number in the place indicated in the installation instructions.

Always quote this serial number when contacting your retailer or Jøtul.

Serial no.

1.0 Relationship to the authorities

Installation of a fireplace must be according to local codes and regulations in each country. All local regulations, including those which refer to national and European standards, must be observed when installing the product.

Both an installation manual with technical data and a manual on general use and maintenance are enclosed with the product. The installation can only be used after it has been inspected by a qualified inspector.

A name plate of heat-resistant material is affixed to the product. This contains information about identification and documentation for the product.

2.0 Technical data

Material:	Cast iron
Finish:	Black paint, enamel
Fuel:	Wood
Log length, max.:	55 cm
Flue outlet:	Top/back
Flue pipe dimension:	150 mm, 177 cm ^2 cross section
Approx. weight:	200 kg
Optional extras:	Connecting pipe for outdoor ventilation, rear heat shield
Dimensions, distances etc.	See fig. 1

Technical data according to EN 13240

Nominal heat output:	8,5 kW
Flue gas mass flow:	8,0 g/sec
Recommended chimney draught:	10 Pa
Efficiency:	78%@8,7 kW
CO emission (13% O_2 ):	0,10%
Flue gas temperature:	285°C
Operational type:	Intermittent

“Intermittent combustion” here means normal use of a stove. That is to say, if you want to continue producing heat, you add more fuel as soon as the previous load of wood has burnt down to embers.

Wood consumption

Jøtul F 500 has a nominal heat output of 8,5 kW. Use of wood, with nominal heat emission: Approx. 2,7 kg/h. Another important factor for proper fuel consumption is that the logs are the correct size. The size of the logs should be:

Kindling:

Length: 30 - 55cm

Diameter: 2 - 5 cm

Amount per fire: 8 -10 pieces

Firewood (split logs):

Recommended length: 35 cm

Diameter: Approx. 8 - 13 cm

Intervals for adding wood: Approximately every 80 minutes

Size of the fire: 3,5 kg

Amount per load: 2 - 3 pieces

Nominal heat emission is achieved when the airvent is open approximately 50%.

ENGLISH

3.0 Installation

3.1 Floor

Foundations

It must be ensured that the foundations are dimensioned for the fireplace. Cf. «2.0 Technical data» for specification of weight. It is recommended that flooring which is not fastened to the foundations – so-called floating flooring – is removed during installation.

Wooden floor protection

Jøtul F 500 has a heat shield underneath which protects the floor from radiation. The product can therefore be placed directly on a wooden floor that is covered by a metal plate or other suitable, non-inflammable material. The recommended minimum thickness is 0,9 mm.

Any flooring made of combustible material, such as linoleum, carpets, etc. must be removed from under the floor plate.

Requirement for protecting combustible flooring in front of fireplace

The front plate must be in accordance with national laws and regulations. See fig.1.

Contact your local building authority regarding restrictions and installation requirements.

3.2 Walls

Note! The side load door must not be used in corner installations.

Distance to wall made of combustible material-see fig. 1

The fireplace is authorised for use with the distances to the wall of flammable material as shown in fig. 1.

A heat shield for the back can be ordered and mounted depending on the position of the fireplace and the desired distance to combustible materials. See fig. 1.

Distance to walls covered by a firewall

Firewall requirement

The firewall must be at least 100 mm thick and be made of brick, concrete-stone or light concrete. Other materials and structures with satisfactory documentation may also be used.

3.3 Ceiling

There must be a minimum distance of 1200 mm to a combustible ceiling above the fireplace.

3.4 Chimneys and flue pipes

• A chimney can be linked to the fireplace and flue approved for solid fuel-fired fireplaces with a flue gas temperature as specified in «2.0 Technical data».

• The cross-section of the chimney must be at least equal to the cross-section of the flue. Please use «2.0 Technical data» to calculate the correct cross-section of the chimney.

• Several solid fuel-fired fireplaces can be connected to the same chimney if the cross-section of the chimney is adequate.

• Connection to the chimney must be carried out in accordance with the installation instructions from the supplier of the chimney.
• Before making a hole in the chimney the fireplace should be test-mounted in order to correctly mark the position of the fireplace and the hole in the chimney. See fig.1 for minimum dimensions.
• Ensure that the flue pipe is inclined all the way up to the chimney.
• Use a flue pipe bend with a sweeping hatch that allows it to be swept.

Be aware of the fact that it is particularly important that connections have a certain flexibility in order to prevent movement in the installation leading to cracks.

N.B. A correct and sealed connection is very important for the proper functioning of the product.

Recommended chimney draught: See «2.0 Technical data». If the draught is too strong you can install and operate a flue damper to control the draught.

3.5 Assembly prior to installation

Note! Check that the stove is free of any damage prior to commencing installation.

The product is heavy! Make sure you have assistance when erecting and installing it.

A heat shield for the floor shall always be used. A heat shield for the back can be ordered and mounted depending on the position of the fireplace and the desired distance to combustible materials. See fig. 1.

1. The oval top plate is fastened with screws during transport. Remove the screws from underneath the top plate and leave it unattached. This makes it easier for the chimney sweep when the product and the flue pipe have to be cleaned.
2. Take out the ash lips, which are inside the burn chamber, and install. The one in front is placed loosely on top of the base plate, while the side ash lip is fastened with the screw that is attached to the base plate.
3. Fasten the heat shield under the middle using 2 M6 x 12 screws. Follow the fig. 5.

Mounting of flue pipe

The stove is installed with a 150 mm diameter flue pipe. This must be an approved thickness.

The flue outlet for Jøtul F 500 is inside the burn chamber during transportation. You can choose between a top or rear outlet from the flue pipe. The screws for fastening are in the bag containing screws.

1. Flue pipes 150 mm dia. are placed directly onto the product flue outlet. There is a screw on both sides of the product flue outlet (fig. 3A). These are used to fasten the flue pipe.
2. Mark where the screws hit the flue pipe when it is at the very bottom of the flue outlet and drill a 5,5 mm hole for the screw in the flue pipe.
3. Use gasket and cement to seal between flue pipe and product flue outlet. Place the gasket around the lower part of the flue pipe and fill up the space with cement.
4. Fasten the flue pipe with screws.

Note! It is important that the joints are completely sealed. Air leakage etc. may lead to malfunction.

3.6 Control of functions (fig. 2)

When the product is set up, always check the control functions.

These shall move easily and function satisfactorily.

Draught vent (A)

Left position = closed

Right position = fully open

Doorhandle (B)

Towards the left = open

Towards the right = closed

Doorhandle (C)

Towards the right = open

Towards the left = closed

Ash door (E)

Open the door by turning the knob counter-clockwise one half rotation.

3.7 Ash removal

Jøtul F 500 has an ash pan which makes it easy to remove the ash.

1. Scrape the ash through the grate in the base plate and into the ash pan. Use something like a glove to grab the handle on the ash pan.

2. Make sure that the ash pan doesn't fill up so high that it keeps ash from coming through the grate into the pan.

3. Make sure the door to the ash pan is securely shut when the stove is in use.

For the rest, see description of how to handle ash in the Manual on general use and maintenance in Point «6.1 Fire preventive measures».

4.0 Service

Warning! Any unauthorised change to the product is illegal. Only use original spare parts.

4.1 Changing the baffle plate

1. The baffle plate consists of a vermeculite plate, and rests on top of the pipes that supply secondary air.
2. To remove, just lift it off and out
3. To install, follow the same procedure in opposite sequence. Make sure the vermeculite plate is fitted closely against the back wall. Be aware that the vermeculite plate may be damaged by rough handling.
4. Then place the insulating blanket on top of the baffle plate.

4.2 Changing the burn plates

1. The stove has burn plates that are mounted to the sides and fire bricks in the back.
2. Unfasten the screws and remove the burn plates. To reinstall, make sure the insulation is properly fastened to back of the burn plates.
3. The bricks at the back are easy to change. Simply lift up a little and pull out.

5.0 Optional equipment

5.2 Connecting pipe for outdoor ventilation - Cat. No. 221031

With the aid of a connecting pipe for outdoor ventilation and a flexible tube, combustion air can be connected to the product directly from the outside. In this manner, the fireplace will always be supplied with the air needed to achieve proper combustion.

Fresh air supply direct from the exterior or from the chimney with air vents

1. Insert the connecting pipe into the air inlet under the product.
2. Unfold the pipe"s 3 flaps (fig. 5A) inside the air inlet.
3. Attach a flexible tube ( 80 mm) directly to the fireplace's connecting pipe by using a hose clamp and attach it to the wall outlet/chimney.

5.2 Rear heat shield- Cat.No. 350956

Assembly instruction follows the product.

ESPAÑOL

Testum Jolal Team heater finality available tool Standard: Children in diameter to adjacent commercial units tall. Senior and/or other units to adjacent commercial units tall. Trade in diameter to adjacent commercial units tall. Trade in diameter to adjacent commercial units tall. Trade in diameter to adjacent commercial units tall. Trade in diameter to adjacent commercial units tall. Trade in diameter to adjacent commercial units tall. Trade in diameter to adjacent commercial units tall. Trade in diameter to adjacent commercial units tall. Trade in diameter to adjacent commercial units tall. Trade in diameter to adjacent commercial units tall. Trade in diameter to adjacent commercial units tall. Trade in diameter to adjacent commercial units tall. Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade in diameter: 100% Trade is not a single, then the only non-mermaidual funds. Mentage and Bedienungsanleitung beachten. Verwerten Sie nur emprechteen Brandstoffe. Beckreden des sonstigen derivatoren. Utilize unmittelment in communisierungen im mermaidus. Fertile no. No. four years, Team plan. Manufacturier: Jipal A5 TOB 2442 No.36-32 Predifikation Narway

Formul Jolal Team heater healthy/healthy food
Standard Children in the country to be present commercials made in Citation and distribution of the company's market in the local Area of the city, which is expected by the growing population Careholder's daily Affinity Opposition range All type Group of type The group was estimated as a measure for
Country	Classification	Co-finger standard	Approved by
Norway	Kissier-1
South	UK	GP	Dr. Montes' Farming-of- Cereansparks total GP
a. North	Nordland	PK	Dr. Montes' National Farming and Research institute
Follow-up's initiative, are: Our only economical foods Wardings and Bodenungsstratung bruchters. We'vedled 'Se our emittenden Bredicofactors. Described less consignet distribution. Utilise unconsignment and Commissions in remanisms.
Serifinal Y. yxxx, Year 2006
Manufacturant: Jolal AS POB 1441 No-2632 Predilikstad Hormley			222,745

Durchmesser: 2 - 5 cm

Brennholz (Scheite):

Durchmesser: ca. 8 - 13 cm

Product: Jøtul F 500

Y X 700 61

Min. mål gulvplate / measure floorplate X/Y = Acc. to national standards and regulations

128 217 83 Stuss for uteluft Outside air convection Ø76mm

Målene gjelder ubehandlede produkter. Etter lakkering eller emaljering kan målene variere noe. Dimensions refer to untreated products. After painting or enamelling dimensions may have small divergences.

Quality control of stoves and fireplaces

Checked