JL027296N - Air bed JILONG - Free user manual and instructions

USER MANUAL JL027296N JILONG

Important Safety Guideline Please read, understand and follow all instructions prior to using. To enhance the enjoyment of your Air Bed and protect the safety of the operator using the product, ALWAYS STRICTLY OBSERVE the following important safety points. The following important points should be read and understand before using this product:

1. WARNING: To prevent possible electric shock, do not attempt to plug in power

cord with wet hands.

2. WARNING: To prevent possible electric shock, connect power cord into a

grounded receptacle protected by a ground-fault circuit interrupter (GFCI).

3. WARNING: To prevent possible electric shock, never use a damaged or frayed

power cord. If the supply cord is damaged, it must be replaced by the manufactured or its service agent or a similarly qualified person in order to avoid a hazard.

4. WARNING: Do not extension power cords with this product.

5. WARNING: Only for indoor household use. Keep away from fire.

6. WARNING: In order to reduce the risk of electric shock, do not expose to rain.

7. RISK OF COMBUSTION: Do not place the airbed against or near any open

flames, heaters, furnaces or other hot objects.

8. IMPORTANT: Do not operate electric pump for more than 5 minutes at one

time (Generally, 5 minutes for each inflation or deflation is enough), take 20 minutes break between uses, as overheating may occur and pump will automatically shut off. It will be ready to use after it has cooled down. This automatic shut off is for your safety. Unplug electrical power cord when not in use.

9. WARNING: Do not obstruct the air passage opening or insert any objects into

the opening at any time.

10. WARNING: Do not stand, jump or use the airbed as a trampoline. Always

supervise children near the airbed.

11. WARNING: This product is not a raft or floatation device. Do not use near or

12. WARNING: Children must not be left unattended when using the airbed. Use

only under adult competent supervision.

13. WARNING: The storage bag is not a toy. To avoid danger of suffocation, keep

the airbed storage bag or any other bags away from babies and children. Fold up the bag and store away from children when not in use.

14. WARNING: Keep pets away from the airbed. Pets may tear or puncture the

15. IMPORTANT: Make sure the area is flat, smooth, even and free of sharp

Instruction Manual Built-in Electric Pump 220 – 240V ~ 50 Hz 130W 120W2 objects that can puncture the airbed. Do not set up the airbed nearby stairs, doors, drops, sharp edges or breakables.

16. IMPORTANT: To minimize any chance of rolling, tipping or swaying, avoid

sleeping on the edge of the airbed. Edges provide less support than the middle of the airbed.

17. IMPORTANT: This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

18. IMPORTANT: Children should be supervised to ensure that they do not play

with the appliance. Inflation instructions

1. Open the cord cover of pump first and make sure the optional inflation air valve is

2. Plug the AC electrical line cord into an AC electrical outlet (ground fault circuit

3. Turn the control dial clockwise until arrow points to the inflation mark ( ).

4. When the airbed is fully inflated to the desired firmness, turn the control dial

counter-clockwise until arrow points to the “OFF”. See Fig. (3)

5. Lie down on the airbed to test the firmness.

6. If the sleeping surface is too hard, adjust the firmness by continuously turning the

control dial counter-clockwise gradually until air start to exit through the air passage. Then turn the control dial clockwise until arrow points to the “OFF” when the desired firmness is achieved. If the airbed becomes too soft, please repeat step 3 thru 5 as necessary.

7. Disconnect the AC line cord from the wall socket and place it inside the cord

compartment. Deflation instructions

1. Open the cord cover of pump first and make sure the optional inflation air valve is

2. Plug the AC electrical line cord into an AC electrical outlet (ground fault circuit

interrupter outlet). Please check the correct voltage! See Fig. (1)

3. Turn the control dial counter-clockwise until arrow points to the deflation mark

( ). See below Fig. (4)

4. When all air is removed from the airbed, turn the control dial clockwise until

arrow points to the “OFF”. See below Fig. (3)

5. When the airbed is completely deflated, begin rolling the airbed from the foot of

the airbed towards the head of the airbed where the pump is located. To ensure the airbed is fully deflated, repeat steps 3 thru 4. Fig.(3)4

6. Disconnect the AC line cord from the wall socket and place it inside the cord

Inflation option If the electric pump is not available then a conventional foot or manually operated air pump can be connected to the optional inflation valve for inflation. See below fig (6).

1. Remove the valve totally from out of the valve insertion, and then pull the stopper

out of the valve extension. Inflate the product by air pumps. Blow in sufficient air in order to fill up the chamber to the full extent. Do not use air compressor or high pressure pumps. Do not over inflate: excessive inflation of the air chambers can cause the chamber to burst or cause damage to the welding seams.

2. Close the valve by firmly inserting the stopper and press the valve into the chamber

until the valve sits flush with the chamber. Fig.(4)5 Storage and Maintain

1) Clean the product with clear water, then leave it in shady and cool place for airing,

fold it into original package and place it indoor for next use. Caution: Do not use the alkali or acid detergent to clean product! Do not leave product exposed under sunlight directly because it will shorten the using-life of product.

2) Fold the airbed loosely and avoid sharp bends, corners and creases which can

3) No specific maintenance is required for the built-in electric pump.

4) Place the airbed inside the storage bag and store in a dry and room temperature