Caffe Dell'Opera - Coffee machine NEMOX - Free user manual and instructions

USER MANUAL Caffe Dell'Opera NEMOX

English IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be observed, including the following:

• Read all instructions carefully. •Do not touch hot surfaces. Use handles or knobs.
• To protect against risk of fire, electric shock, and injury to persons do not immerse cord or plug or appliance in water or any other liquid.
• Close supervision is necessary when any appliance is used by or near children.
• Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance.

• Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions, or if it is dropped or damaged in any manner. Return appliance to the nearest authorized Service Center for examination, repair or electrical or mechanical adjustment.

• The use of accessory attachments not recommended or sold by the appliance manufacturer may result in fire, electric shock or injury.
• Do not use outdoors.•Do not let cord hang over edge of table or counter, or touch hot surfaces.•Do not place on or near a hot gas or electric burner, or in a heated oven.
• Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control to “OFF” or “0”, then remove plug from wall outlet.

• Do not use appliance for other than intended use. The manufacturer cannot be considered responsible for any damage caused by improper, incorrect or unreasonable use.

SAVE THESE INSTRUCTIONS

• After removing the appliance from the packaging, check it for damage. If in doubt, do not use the appliance and contact an authorised service centre.

• Plastic bags, polystyrene, nails, etc. must not be left within reach of children as they are potentially dangerous.

• The appliance must be connected to an electrical system and power supply socket with a minimum capacity of 10A, equipped with an efficient earth contact. The manufacturer is not responsible for any damage caused by failure to earth the system.

• Any repairs must only be carried out by authorised service centres. (This includes replacement of the power supply cable, since special tools are required).

• The appliance's manufacturer and vendor reject any responsibility for failure to comply with the instructions provided in this user manual.
• Never operate the appliance without water; it would be damaged beyond repair.•Never touch hot parts of the appliance with bare hands, as burns might result.
• The appliance dispenses hot water and steam, and temperatures are therefore high. Take great care to avoid burns.
• Never remove the filter holder when the appliance is pressurized or is dispensing coffee.•Never leave water inside the appliance at temperatures of 0°C or below.
• Before carrying out any maintenance or cleaning operations, make sure that the appliance has been disconnected from the electrical mains by removing the plug from the power supply socket.
• Never wash the appliance using water jets or place it in water!•Never touch the appliance with wet or damp hands or feet. PUTTING THE APPLIANCE INTO SERVICE - USING For hygiene reasons, the water in the tank should

IT FOR THE FIRST TIME

also be changed and the washing procedure carried out if the appliance is left unused for more Wash all the accessories in the packaging carefully. than a week. In this case, replace the water still in Remove the tank (1) from its seat and clean it the tank with fresh water before starting the thoroughly. Then fill it with fresh water and put it cleaning process. back in place. Caution: take care to fit the filler hose properly, with no kinks or restrictions which might ADJUSTING GRINDING (OPERA)impair water intake. Fill the container (14) with coffee beans. The Connect the plug to the power supply socket after numbered scale on the container indicates the checking that the voltage on the electrical data plate grinding level setting. is the same as the mains voltage. Press the master

switch (4); the light inside the switch will illuminate Taking the notch on the frame of the machine as to show that the appliance is receiving power. Load reference, turn the coffee grinding regulator knob water into water circuit immediately as described (15) until the number corresponding to the desired in the paragraph below. Do not let the machine grinding fineness is in line with the reference notch. powered without the water circuit loaded. High numbers give coarser grinding and low Wash the coffee making unit proceeding as numbers finer grinding. Setting the correct grinding follows: fineness is fundamental in obtaining a goods, creamy Remove the filter holder (11) and press the coffee cup of coffee. The right setting depends on the dispenser switch (7); the pump will start to load different blends of coffee available on the market and water. Wait until water flows from the boiler outlet personal preference. (10). Now, the appliance's water circuit is now MAKING ESPRESSO COFFEEprimed. Make sure that the operations described in the Press the coffee switch (7) to bring it to the “0” PUTTING THE APPLIANCE INTO SERVICE section position and stop the flow. have been carried out. Repeat the operation whenever the appliance's Wait until the water/steam temperature light (3) water circuit has to be re-primed because the goes out, indicating that the appliance is ready to tank has been emptied completely. Do not let make coffee (while the appliance is in use, the light the machine powered without the water circuit will go on whenever the water temperature drops loaded. below the pre-set values. Do not start to make For hygiene reasons, the water in the tank should coffee until the light is off). also be changed and washing procedure carried Place the filter for one cup or for two cups in the filter out if the appliance is left unused for more than a holder (11). week. In this case, replace the water still in the tank with fresh water before starting the cleaning OPERA. Place the filter holder against the support process. provided under the coffee outlet (16) and press the button (17) to start coffee grinding. When the When the appliance is used for the first time, allow desired quantity is reached, release the coffee about a litre of water to flow to ensure it is grinding button (17).thoroughly cleaned. FENICE. Whit the doser measure, place the ground Then wash the hot water/steam dispenser unit coffee in the filter (one measure = one cup; two proceeding as follows: measures = two cups). Turn on the steam/hot water tap (5) by turning it Use the presser (8) to press the coffee in the filter anti-clockwise. firmly down. The creaminess of the coffee will Press the hot water dispenser switch (13); the depend on how the beans have been ground and pump will start to load water. Wait until an even jet how hard the grounds are pressed down (if the of water, containing no air, flows from the hot coffee is damp or finely ground, lighter pressure is water/steam dispenser spout (9). sufficient, while if it is coarsely ground it requires a When the appliance is used for the first time, allow firmer pressure). Remove any excess coffee from about a litre of water to flow from the steam spout the rim of the filter. to ensure it is thoroughly cleaned. Connect the filter holder (11) under the boiler outlet Press the hot water switch (13) to bring it to the (10), turning it from left to right until it cannot be "0" position and turn off the steam/hot water tap turned any further. Caution: it is important always (5) by turning it clockwise to stop the flow. to push the filter holder firmly home until it cannot

English IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be observed, including the following:

• Read all instructions carefully. •Do not touch hot surfaces. Use handles or knobs.
• To protect against risk of fire, electric shock, and injury to persons do not immerse cord or plug or appliance in water or any other liquid.
• Close supervision is necessary when any appliance is used by or near children.
• Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance.

• Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions, or if it is dropped or damaged in any manner. Return appliance to the nearest authorized Service Center for examination, repair or electrical or mechanical adjustment.

• The use of accessory attachments not recommended or sold by the appliance manufacturer may result in fire, electric shock or injury.
• Do not use outdoors.•Do not let cord hang over edge of table or counter, or touch hot surfaces.•Do not place on or near a hot gas or electric burner, or in a heated oven.
• Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control to “OFF” or “0”, then remove plug from wall outlet.

• Do not use appliance for other than intended use. The manufacturer cannot be considered responsible for any damage caused by improper, incorrect or unreasonable use.

SAVE THESE INSTRUCTIONS

• After removing the appliance from the packaging, check it for damage. If in doubt, do not use the appliance and contact an authorised service centre.

• Plastic bags, polystyrene, nails, etc. must not be left within reach of children as they are potentially dangerous.

• The appliance must be connected to an electrical system and power supply socket with a minimum capacity of 10A, equipped with an efficient earth contact. The manufacturer is not responsible for any damage caused by failure to earth the system.

• Any repairs must only be carried out by authorised service centres. (This includes replacement of the power supply cable, since special tools are required).

• The appliance's manufacturer and vendor reject any responsibility for failure to comply with the instructions provided in this user manual.
• Never operate the appliance without water; it would be damaged beyond repair.•Never touch hot parts of the appliance with bare hands, as burns might result.
• The appliance dispenses hot water and steam, and temperatures are therefore high. Take great care to avoid burns.
• Never remove the filter holder when the appliance is pressurized or is dispensing coffee.•Never leave water inside the appliance at temperatures of 0°C or below.
• Before carrying out any maintenance or cleaning operations, make sure that the appliance has been disconnected from the electrical mains by removing the plug from the power supply socket.
• Never wash the appliance using water jets or place it in water!•Never touch the appliance with wet or damp hands or feet.PUTTING THE APPLIANCE INTO SERVICE - USING For hygiene reasons, the water in the tank should IT FOR THE FIRST TIME also be changed and the washing procedure carried out if the appliance is left unused for more Wash all the accessories in the packaging carefully. than a week. In this case, replace the water still in Remove the tank (1) from its seat and clean it the tank with fresh water before starting the thoroughly. Then fill it with fresh water and put it cleaning process.back in place. Caution: take care to fit the filler hose properly, with no kinks or restrictions which might ADJUSTING GRINDING (OPERA)impair water intake.Fill the container (14) with coffee beans. The Connect the plug to the power supply socket after numbered scale on the container indicates the checking that the voltage on the electrical data plate grinding level setting.is the same as the mains voltage. Press the master 7 . 6 . 5 . 4 . 3 . 2 . 1switch (4); the light inside the switch will illuminate Taking the notch on the frame of the machine as to show that the appliance is receiving power. Load reference, turn the coffee grinding regulator knob water into water circuit immediately as described (15) until the number corresponding to the desired in the paragraph below. Do not let the machine grinding fineness is in line with the reference notch.powered without the water circuit loaded. High numbers give coarser grinding and low Wash the coffee making unit proceeding as numbers finer grinding. Setting the correct grinding follows:fineness is fundamental in obtaining a goods, creamy Remove the filter holder (11) and press the coffee cup of coffee. The right setting depends on the dispenser switch (7); the pump will start to load different blends of coffee available on the market and water. Wait until water flows from the boiler outlet personal preference.(10). Now, the appliance's water circuit is now MAKING ESPRESSO COFFEEprimed.Make sure that the operations described in the Press the coffee switch (7) to bring it to the “0” PUTTING THE APPLIANCE INTO SERVICE section position and stop the flow.have been carried out.Repeat the operation whenever the appliance's Wait until the water/steam temperature light (3) water circuit has to be re-primed because the goes out, indicating that the appliance is ready to tank has been emptied completely. Do not let make coffee (while the appliance is in use, the light the machine powered without the water circuit will go on whenever the water temperature drops loaded.below the pre-set values. Do not start to make For hygiene reasons, the water in the tank should coffee until the light is off).also be changed and washing procedure carried Place the filter for one cup or for two cups in the filter out if the appliance is left unused for more than a holder (11).week. In this case, replace the water still in the tank with fresh water before starting the cleaning OPERA. Place the filter holder against the support process.provided under the coffee outlet (16) and press the button (17) to start coffee grinding. When the When the appliance is used for the first time, allow desired quantity is reached, release the coffee about a litre of water to flow to ensure it is grinding button (17).thoroughly cleaned.FENICE. Whit the doser measure, place the ground Then wash the hot water/steam dispenser unit coffee in the filter (one measure = one cup; two proceeding as follows:measures = two cups).Turn on the steam/hot water tap (5) by turning it Use the presser (8) to press the coffee in the filter anti-clockwise.firmly down. The creaminess of the coffee will Press the hot water dispenser switch (13); the depend on how the beans have been ground and pump will start to load water. Wait until an even jet how hard the grounds are pressed down (if the of water, containing no air, flows from the hot coffee is damp or finely ground, lighter pressure is water/steam dispenser spout (9). sufficient, while if it is coarsely ground it requires a When the appliance is used for the first time, allow firmer pressure). Remove any excess coffee from about a litre of water to flow from the steam spout the rim of the filter.to ensure it is thoroughly cleaned.Connect the filter holder (11) under the boiler outlet Press the hot water switch (13) to bring it to the (10), turning it from left to right until it cannot be "0" position and turn off the steam/hot water tap turned any further. Caution: it is important always (5) by turning it clockwise to stop the flow.to push the filter holder firmly home until it cannot

IMPORTANT: Check that there are no foreign circuit as described in the PUTTING THE bodies with the coffee beans; they might damage APPLIANCE INTO SERVICE section. the grinders. Tale care not to pour water straight The water temperature is too high, the steam into the coffee grinder, it damages the grinders! function has been used without discharging the Clean the appliance using a soft, damp cloth only residual steam from the spout. Leave the appliance and then dry. Never use solvents, detergents, to cool for a few minutes, then proceed as abrasives or any substances not suitable for described in the PUTTING THE APPLIANCE INTO contact with foods. SERVICE - USING IT FOR THE FIRST TIME - wash the coffee maker unit. The steam outlet tip may be removed for cleaning by turning it clockwise. It must be cleaned Coffee flows out too quickly. whenever the steam/hot water spout is used to heat The coffee is too coarsely ground. milk or liquids. The coffee inside the filter has not been pressed Never place the appliance in water; it contains down firmly enough. electrical parts! There is not enough coffee in the filter. Coffee flows out too slowly. DESCALING The coffee is too finely ground. In some areas, the water contains a large amount of scale, which is deposited in the appliance's circuit, The coffee inside the filter has been pressed down impairing its operation. too firmly. The appliance should be de-scaled every 3-4 months Some of the holes in the filter are blocked; free them or about every 300 coffees, proceeding as follows. with a needle. 1). Fill the tank (1) with water, adding about 100 cc of The coffee is not creamy. white wine vinegar or a de-scaling product, for The coffee is too coarsely ground. use with foods, using the quantity stated in the The coffee is no longer fresh. instructions. The blend used is not suitable for espresso. 2). Switch on the master switch (4). Proceed as if The coffee is not hot enough. making coffee, allowing a cappuccino cup full of The cup, filter and filter holder have not been water to flow out. warmed up. 3). Then dispense hot water through the spout (9), You have not waited for the water temperature light allowing a cappuccino cup full of water to flow (3) to go out. out. The steam/water spout does not dispense steam or 4). Turn off the master switch and leave the descaling water. product to act for about 15-20 minutes. The hole in the spout is blocked by dried residues. 5). Repeat the operations described in points 2-3-4 Clean the hole with a needle. until the water tank is empty. It is difficult to connect the filter holder. 6). Wash the tank thoroughly and fill it with fresh Too much coffee has been put in the filter holder. water. Remove a little coffee before connecting. 7). Clean the circuit as described in the PUTTING THE There is coffee on the rim of the filter. Clean both the APPLIANCE INTO SERVICE - USING IT FOR THE filter and the corresponding connection zone FIRST TIME section. around the boiler outlet. WHAT MIGHT GO WRONG? OPERA - The coffee grinder does not dispense the The indicator lights do not come on. ground coffee. No power. The coffee is being ground too fine. Set coarser Check that the plug has been connected to the grinding. power supply socket correctly. If the noise indicating that the coffee grinder motor The power supply lead is damaged. Remove the is running is not heard, contact an authorised plug immediately and take the appliance to an service centre. authorised service centre. You are urged to check all the points listed above The appliance does not make coffee. before calling in an authorised service centre. The water tank is empty or the water circuit has not If the service centre does not find any been primed. In both cases, an abnormal noise will malfunctions, the expenses for these checks will be heard, since the pump will be sucking in air be charged to the customer. instead of water. Switch off the appliance and leave it to cool for a few minutes, then prime the water

be turned any more, to ensure a secure connection. bottom to the top of the container. The steam spout has a special tip which aids the formation of froth Place the coffee cups under the spouts of the filter on milk. holder (11) and press the coffee dispenser switch (7). When the desired amount of coffee has been When enough steam has been dispensed, move the steam/hot water spout (9) back over the grating obtained, return the switch (7) to "0". (12), turn off the steam switch (6) by moving it Remove the filter holder (11) by turning from right to to”0” and press the hot water switch (13). Wait until left and throw the grounds away. Never leave the the water is expelled from the spout (9) and press filter containing the spent grounds connected to the the hot water switch (13) by moving it to “0”. This appliance. operation empty the steam/hot water spout from Note: it is normal for a few drops of water to flow the residual steam and re-prime the water circuit. from the boiler outlet; this does not mean that the Turn the steam/hot water tap (5) off again by appliance is defective. turning it clockwise.

USEFUL HINTS FOR MAKING DELICIOUS ITALIAN

Clean the steam spout and outlet tip thoroughly. ESPRESSO

USEFUL HINTS FOR MAKING DELICIOUS ITALIAN

Always use fresh water and clean the tank often. CAPPUCCINO Do not make coffee until the water has reached the First make the coffee in a cappuccino cup. optimum temperature (indicated by the light (3), Fill just 1/3 of the container to be used with cold which goes out). milk. To obtain dense froth, place the evaporator tip Do not wash the filters and the filter holder (11) with just below the level of the milk and turn the detergent whenever they have been used; rinsing container in circles until the desired consistency is with water is sufficient. However, it is important to obtained. Then insert the spout down to the bottom check that coffee residues have not blocked the tiny of the container until the milk is heated to the holes in the filters. temperature required. Warm the cups, filters and filter holder before Add the milk to the coffee and use a spoon to carry making coffee. The cups can be warmed by placing the desired amount of froth into the cup. The them on the cup warmer shelf (2) with the optimum proportion for a good cappuccino is 1/3 appliance switched on. The filters and filter holder coffee, 1/3 hot milk and 1/3 milk froth. can be warmed with hot tap water or by connecting Dust with cocoa powder if liked. the filter holder containing the filter to be used (without coffee, naturally) under the boiler outlet. HOT WATER Press the coffee switch (7) and allow a cup full of Make sure that the operations described in the water to flow out. Disconnect the filter holder and PUTTING THE APPLIANCE INTO SERVICE section filter and dry them before adding the coffee. have been carried out. Do not use paper or plastic cups, as the flavour of Wait until the indicator light (3) goes out. the coffee is affected. Turn on the steam/hot water tap (5) by turning it Good quality, well roasted coffee ground to the right anti-clockwise; a little water will come out of the fineness is essential for making good espresso. spout. Now press the switch (13) to obtain a DISPENSING STEAM continuous flow of water at a temperature of about 95°C. Make sure that the operations described in the PUTTING THE APPLIANCE INTO SERVICE section When the desired amount of water has been have been carried out. obtained, switch off the switch (13) and turn off the tap (5) by turning it clockwise. Press the steam switch (6) and wait until the water/steam temperature indicator light (3) goes ROUTINE MAINTENANCE out. Before carrying out any maintenance or cleaning Turn the steam/hot water spout so that it is over the operation, remove the plug from the power supply drip tray (12). Turn on the steam/hot water tap (5) socket and leave the appliance to cool. slightly by turning it anti-clockwise and wait until Clean the drip tray, the tank, the filters and the filter only steam comes out of the spout. Turn off the tap. holder regularly. Turn the spout outward and insert it to the bottom of Clean the coffee grinder container the recipient containing the beverage to be heated. periodically using a slightly damp cloth to remove Turn the steam tap fully on and heat the liquid by the coffee powder. moving the spout in circles, working from the

IMPORTANT: Check that there are no foreign circuit as described in the PUTTING THE bodies with the coffee beans; they might damage APPLIANCE INTO SERVICE section. the grinders. Tale care not to pour water straight The water temperature is too high, the steam into the coffee grinder, it damages the grinders! function has been used without discharging the Clean the appliance using a soft, damp cloth only residual steam from the spout. Leave the appliance and then dry. Never use solvents, detergents, to cool for a few minutes, then proceed as abrasives or any substances not suitable for described in the PUTTING THE APPLIANCE INTO contact with foods. SERVICE - USING IT FOR THE FIRST TIME - wash the coffee maker unit. The steam outlet tip may be removed for cleaning by turning it clockwise. It must be cleaned Coffee flows out too quickly. whenever the steam/hot water spout is used to heat The coffee is too coarsely ground. milk or liquids. The coffee inside the filter has not been pressed Never place the appliance in water; it contains down firmly enough. electrical parts! There is not enough coffee in the filter. Coffee flows out too slowly. DESCALING The coffee is too finely ground. In some areas, the water contains a large amount of scale, which is deposited in the appliance's circuit, The coffee inside the filter has been pressed down impairing its operation. too firmly. The appliance should be de-scaled every 3-4 months Some of the holes in the filter are blocked; free them or about every 300 coffees, proceeding as follows. with a needle. 1). Fill the tank (1) with water, adding about 100 cc of The coffee is not creamy. white wine vinegar or a de-scaling product, for The coffee is too coarsely ground. use with foods, using the quantity stated in the The coffee is no longer fresh. instructions. The blend used is not suitable for espresso. 2). Switch on the master switch (4). Proceed as if The coffee is not hot enough. making coffee, allowing a cappuccino cup full of The cup, filter and filter holder have not been water to flow out. warmed up. 3). Then dispense hot water through the spout (9), You have not waited for the water temperature light allowing a cappuccino cup full of water to flow (3) to go out. out. The steam/water spout does not dispense steam or 4). Turn off the master switch and leave the descaling water. product to act for about 15-20 minutes. The hole in the spout is blocked by dried residues. 5). Repeat the operations described in points 2-3-4 Clean the hole with a needle. until the water tank is empty. It is difficult to connect the filter holder. 6). Wash the tank thoroughly and fill it with fresh Too much coffee has been put in the filter holder. water. Remove a little coffee before connecting. 7). Clean the circuit as described in the PUTTING THE There is coffee on the rim of the filter. Clean both the APPLIANCE INTO SERVICE - USING IT FOR THE filter and the corresponding connection zone FIRST TIME section. around the boiler outlet. WHAT MIGHT GO WRONG? OPERA - The coffee grinder does not dispense the The indicator lights do not come on. ground coffee. No power. The coffee is being ground too fine. Set coarser Check that the plug has been connected to the grinding. power supply socket correctly. If the noise indicating that the coffee grinder motor The power supply lead is damaged. Remove the is running is not heard, contact an authorised plug immediately and take the appliance to an service centre. authorised service centre. You are urged to check all the points listed above The appliance does not make coffee. before calling in an authorised service centre. The water tank is empty or the water circuit has not If the service centre does not find any been primed. In both cases, an abnormal noise will malfunctions, the expenses for these checks will be heard, since the pump will be sucking in air be charged to the customer. instead of water. Switch off the appliance and leave it to cool for a few minutes, then prime the water

be turned any more, to ensure a secure connection. bottom to the top of the container. The steam spout has a special tip which aids the formation of froth Place the coffee cups under the spouts of the filter on milk. holder (11) and press the coffee dispenser switch (7). When the desired amount of coffee has been When enough steam has been dispensed, move the steam/hot water spout (9) back over the grating obtained, return the switch (7) to "0". (12), turn off the steam switch (6) by moving it Remove the filter holder (11) by turning from right to to”0” and press the hot water switch (13). Wait until left and throw the grounds away. Never leave the the water is expelled from the spout (9) and press filter containing the spent grounds connected to the the hot water switch (13) by moving it to “0”. This appliance. operation empty the steam/hot water spout from Note: it is normal for a few drops of water to flow the residual steam and re-prime the water circuit. from the boiler outlet; this does not mean that the Turn the steam/hot water tap (5) off again by appliance is defective. turning it clockwise.

USEFUL HINTS FOR MAKING DELICIOUS ITALIAN

Clean the steam spout and outlet tip thoroughly. ESPRESSO

USEFUL HINTS FOR MAKING DELICIOUS ITALIAN

Always use fresh water and clean the tank often. CAPPUCCINO Do not make coffee until the water has reached the First make the coffee in a cappuccino cup. optimum temperature (indicated by the light (3), Fill just 1/3 of the container to be used with cold which goes out). milk. To obtain dense froth, place the evaporator tip Do not wash the filters and the filter holder (11) with just below the level of the milk and turn the detergent whenever they have been used; rinsing container in circles until the desired consistency is with water is sufficient. However, it is important to obtained. Then insert the spout down to the bottom check that coffee residues have not blocked the tiny of the container until the milk is heated to the holes in the filters. temperature required. Warm the cups, filters and filter holder before Add the milk to the coffee and use a spoon to carry making coffee. The cups can be warmed by placing the desired amount of froth into the cup. The them on the cup warmer shelf (2) with the optimum proportion for a good cappuccino is 1/3 appliance switched on. The filters and filter holder coffee, 1/3 hot milk and 1/3 milk froth. can be warmed with hot tap water or by connecting Dust with cocoa powder if liked. the filter holder containing the filter to be used (without coffee, naturally) under the boiler outlet. HOT WATER Press the coffee switch (7) and allow a cup full of Make sure that the operations described in the water to flow out. Disconnect the filter holder and PUTTING THE APPLIANCE INTO SERVICE section filter and dry them before adding the coffee. have been carried out. Do not use paper or plastic cups, as the flavour of Wait until the indicator light (3) goes out. the coffee is affected. Turn on the steam/hot water tap (5) by turning it Good quality, well roasted coffee ground to the right anti-clockwise; a little water will come out of the fineness is essential for making good espresso. spout. Now press the switch (13) to obtain a DISPENSING STEAM continuous flow of water at a temperature of about 95°C. Make sure that the operations described in the PUTTING THE APPLIANCE INTO SERVICE section When the desired amount of water has been have been carried out. obtained, switch off the switch (13) and turn off the tap (5) by turning it clockwise. Press the steam switch (6) and wait until the water/steam temperature indicator light (3) goes ROUTINE MAINTENANCE out. Before carrying out any maintenance or cleaning Turn the steam/hot water spout so that it is over the operation, remove the plug from the power supply drip tray (12). Turn on the steam/hot water tap (5) socket and leave the appliance to cool. slightly by turning it anti-clockwise and wait until Clean the drip tray, the tank, the filters and the filter only steam comes out of the spout. Turn off the tap. holder regularly. Turn the spout outward and insert it to the bottom of Clean the coffee grinder container the recipient containing the beverage to be heated. periodically using a slightly damp cloth to remove Turn the steam tap fully on and heat the liquid by the coffee powder. moving the spout in circles, working from the