ESLA93 - Shaver PANASONIC - Free user manual and instructions

USER MANUAL ESLA93 PANASONIC

Operating Instructions

Before operating this unit, please read these instructions completely.2

Warning - Disconnect the power cord from the shaver

before cleaning it to prevent electric shock.

This WET/DRY shaver can be used for wet shaving with

shaving lather or for dry shaving. You can use this watertight

shaver in the shower and clean it in water. The following is

the symbol of Wet shaver. The symbol means that the hand‑

held part may be used in a bath or shower.

Treat yourself to wet lather shaves for at least three weeks

and notice the difference. Your Panasonic WET/DRY shaver

requires a little time to get used to because your skin and

beard need about a month to adjust to any new shaving

‑ The outer foil is very thin and can be damaged if

not used correctly. Check that the foil is not damaged before

using the shaver. Do not use the shaver if the foil etc. is

damaged as you will cut your skin.

Persons using an implanted medical electronic device, such

as a pacemaker, should not allow this unit to touch the skin

where the medical electronic device is implanted because

this may cause a malfunction.

Do not use any power cord, AC adaptor (RE7‑51) or

recharger other than one specifically designed for this

Plug in the adaptor into a household outlet where there is

no moisture and handle it with dry hands.

The shaver and the recharger may become warm during

use and charging. However, this is not a malfunction.

Do not charge the shaver where it will be exposed to direct

sunlight or other heat sources.

Hold the adaptor when disconnecting it from the

household outlet. If you tug on the power cord, you may

The supply cord cannot be replaced. If the cord is

damaged, the appliance should be scrapped.

Keep both the inner blades inserted. If only one of the

inner blades is inserted, the shaver may be damaged.

If you clean the shaver with water, do not use salt water or

Do not soak the shaver in water for a long period of time.

Wipe it with a cloth dampened with soapy water. Do not

use thinner, benzine or alcohol.

Disconnect the power cord when storing the shaver. Do

not bend the power cord or wrap it around the shaver.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety. Children should be supervised to ensure

that they do not play with the appliance.

Keep these operating instructions in a safe place.

Self-cleaning recharger

Do not clean the adaptor or the self

‑cleaning recharger in

water as it will damage them or cause an electric shock.

Do not remove the shaver from the self‑cleaning recharger

while using a course that includes the “Dry” function. A

heater is used so the area around the blades becomes

extremely hot and you may burn yourself.

Place the self‑cleaning recharger on a level and stable

surface. Otherwise the cleaning liquid may spill and

discolor leather products or other surfaces. Wipe it

immediately. The self‑cleaning recharger cleans the inner

blades and the system outer foil. Brush or wash with water

to remove beard trimmings in other areas.

Use the self‑cleaning recharger in temperatures between

15 °C and 35 °C. Otherwise, the following problems may

The time it takes to charge the shaver increases.

The recharger stops functioning.

The lifespan of the rechargeable battery shortens. (Only

when you use the recharger in lower temperatures.) In

this case, the indicators on the LCD panel will blink twice

Use the self‑cleaning recharger in humidity less than 95%.

Depending on the environment, the shaver may not dry

even if you select a course that includes the “Dry” function.

In this case, wipe off any drops of water with a dry cloth.

SPECIFICATIONS Power source: See the name plate on the product.

(Automatic voltage conversion)

Motor voltage: 3.6 V DC Charging time: 1 hour

This product is intended for household use only.

Airborne Acoustical Noise:

In shaving mode: 65 (dB (A) re 1 pW)

In trimmer mode: 67 (dB (A) re 1 pW)

3 System outer foil release

4 Foil frame release

 Water maximum line

Replacement parts are available at your dealer or Service

Replacement parts for ES-LA93

System outer foil and inner blades: WES9025

Charging with the self-cleaning recharger Thoroughly wipe off any drops of water on or around the recharger so that it is dry before charging it.

Plug in the adaptor.

Remove the protective cap and then attach

the shaver. Turn the shaver off before attaching.Check that the outer foil is not deformed or damaged when you are attaching the shaver.The indicators on the LCD panel glow and charging starts.If the indicators on the LCD panel do not glow, wait for a short while until it glows.Charging is completed when the indicators on the LCD panel blink. (Max. 1 hour later)You can keep the shaver attached to the recharger, or connected to the adaptor, when not using it to maintain full battery capacity. You cannot overcharge the shaver. •

• Charging without the rechargerYou can also charge without the recharger.1. Insert the appliance plug into the shaver.2. Plug in the adaptor into a household outlet.

LCD panel when charging The LCD panel shows the remaining battery capacity from 0% to 100%, in 10% increments.While charging After charging is completed10 minutes after charging is completedThe indicators glow.The indicators blink once every second.The indicators b link once every 2 seconds.GB

Apply 4 outer foils in

skin. Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave.CautionIf you press the OFF/ON switch for more than 2 seconds, the turbo mode is activated. Page 10

Shaving in turbo mode may damage your skin. Turn the shaver off and then on again to cancel turbo mode.Do not place your fingers on the OFF/ON switch while using the shaver. This may cause the shaver to turn off or enter turbo mode. •

• Using the trimmer handleYou can change the pivot action. Also, slide the handle up to “” when using the trimmer. FREE You can move the shaver head.

LOCK FREE LOCK You can lock the shaver head.Slide the trimmer handle up. Place at a right angle to your skin and move downwards to trim your sideburns.

FREE LOCK LCD panel when using During use After use

The used time is shown.The indicators turn off after 5 seconds.The shown time returns to [0’00”] after 10 minutes. •

• The used time and the remaining battery capacity are shown alternately after turning off the shaver.When the battery capacity is lowYou can shave 1 to 2 times after “10%” appears. (This will differ depending on usage.) • “10%” appears and blinks.A full charge will supply enough power for approx. 14 shaves of 3 minutes each. •

Cleaning with the self-cleaning recharger

Preparing the self-cleaning recharger

Remove the shaver and the appliance plug from the self‑cleaning recharger.

Do not let the water rise above

the maximum water line. This

may cause the cleaning liquid to

then attach the tank.

cartridge. (2 seals)

Hold the detergent cartridge

horizontally. (The detergent

may spill if the detergent

cartridge is tilted too much.)

Replace the detergent cartridge when the status lamp is illuminated. Use

the below chart as a guide.

Shaving Cleaning Reusability

1 time/day approx. 30 times

1 time/3 days approx. 10 times

The expiration date of the cleaning liquid is 6 months after it is opened. If

you do not use the cleaning liquid for more than 6 months, throw away

the detergent cartridge and the cleaning liquid.

Only use self‑cleaning recharger detergent for Panasonic shavers.

Always change the detergent cartridge and the cleaning liquid in the

water tank at the same time. Adding water, or changing just the detergent

cartridge or the water, will result in deteriorated cleaning functions.

If you operate the self‑cleaning recharger, the concentrated detergent in

the detergent cartridge dilutes and the water inside the tank will become

Keep out of reach of children.

Only use to clean the blades of electric shavers.

Carry out emergency measures if the Cleaning

agent enters mouth or eyes, and consult a doctor.

Plug in the adaptor.

Remove any soap or water on the

shaver if it has been washed with hand

soap or any other detergent.

Remove the protective cap

and then attach the shaver.

Turn the shaver off before attaching.

Check that the outer foil is not deformed

or damaged when you are attaching the

Press [SELECT] to select

The “Charge” course starts when

attaching the shaver.

Each time you press [SELECT], the

course changes from “Clean/Dry/

Charge” “Dry/Charge” “Charge”.

The courses start approximately 6 seconds after they are

The course will be aborted if the power is cut off. In this case,

perform the course again from the beginning.

Do not detach the detergent cartridge or the water tank as

the cleaning liquid may spill causing a malfunction.

Time required (guide)

Charge (0 to 60 min)

Charge (0 to 60 min)

Charge (0 to 60 min)GB

10 English If the status lamp blinks or glows Follow the steps outlined below if the status lamp blinks or glows during the “Clean/Dry/Charge” course.Blinks GlowsCorrectly set the detergent cartridge and then restart a course.Remove the shaver from the self‑cleaning recharger and then check that the [CLEAN] lamp has gone out. (Be careful as the blade may be hot or wet.) Check that the water tank is correctly attached, the water tank cap is securely closed and the self‑cleaning recharger is placed horizontally.If the status lamp goes outContinue a course.When an abnormality has been correctedWhen no abnormality was foundPress and hold [SELECT] for 2 seconds to turn off the status lamp and then restart a course.It is time to replace the detergent cartridge and cleaning liquid inside the water tank.Wash away the old cleaning liquid and then rinse the water tank. Restart the course.When the status lamp goes outWhen the status lamp glows againContinue a course. Contact an authorized service center. 

Cleaning the shaver without the self-cleaning

recharger We recommend that you clean your shaver with the self‑cleaning recharger or the “sonic” vibration turbo‑cleaning mode when the faucet symbol appears on the LCD panel.1. Disconnect the power cord from the shaver.2. Apply some hand soap and some water to the outer foil.3. Slide the switch lock button downwards to unlock the OFF/ON switch.4. Press the OFF/ON switch for more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning. appears on the LCD panel.After about 20 seconds, it will be automatically turned off, or you can turn it off by pressing the OFF/ON switch.5. Remove the outer foil section and press the OFF/ON switch for more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning and clean it with running water.6. Wipe off any drops of water with a dry cloth.7. Dry the outer foil section and the shaver completely.8. Attach the outer foil section to the shaver.9. Lubricate the shaver. •

Cleaning with the brush

1. Press the foil frame release buttons and lift the outer foil

2. Clean the inner blades using the short

brush by moving it in direction (A).

Clean the system outer foil, the shaver

body and the trimmer using the long

Do not move the short brush in

direction (B) as it will damage the

inner blades and affect their

Do not use the short brush to clean

To maintain shaving comfort for a long time, it is

recommended that the oil provided with the shaver is used.

1. Switch off the shaver.

2. Apply one drop of oil to each of the

immer and apply a drop of

4. Switch the shaver on, and run it for

approximately five seconds.

5. Switch off the shaver, and wipe off any

excess oil from the outer foils with a

It is not necessary to oil the blades after using the self‑

cleaning recharger (lubricant is included in the cleaning

Replacing the system outer foil and the inner

appears on the LCD panel once a year. (This will differ

depending on usage.) We recommend checking the system

outer foil and the inner blades when it appears.

Press the OFF/ON switch for more than 30 seconds to delete

system outer foil once every year

inner blade once every two years

Replacing the system outer foil

1. Press the foil frame release buttons

and lift the outer foil section upwards

2. Press the system outer foil release

buttons and pull down the system outer

foil as illustrated.

3. Align the foil frame mark and the

system outer foil mark and securely

The system outer foil cannot be

Always insert the system outer foil to

the foil frame when attaching to the

4. After turning the mark to the front,

securely attach the outer foil section to

the shaver until it clicks.

12 English 2. Gently wipe off any beard trimmings

attached to the inside of the cleaning

tray with a cloth or tissue paper

dampened with water.

Clean the corners and uneven parts

of the cleaning tray with a cotton

swab dampened with water.

Warning ‑ Do not wash or apply water to the adaptor or

self‑cleaning recharger. Failure to observe this may cause

electric shock or result in short circuits.

Do not pull hard on the rubber blade protector at the

bottom of the cleaning tray. The rubber may come off if you

pull hard on it. It is only necessary to pull it up slightly.

When the water does not drain from the

Beard trimmings may clog the drain at

the bottom of the cleaning tray.

In this case, you cannot clean or dry the

Push the beard trimmings down through

the drain with a tooth pick etc.

Replacing the inner blades

1. Press the foil frame release buttons

and lift the outer foil section upwards

. Remove the inner blades one at a time

Do not touch the edges (metal parts)

of the inner blades to prevent injury to

3. Insert the inner blades one at a time

until they click as illustrated.

Cleaning the self-cleaning recharger

Beard trimmings may become attached

to the cleaning tray of the self‑cleaning

recharger. Follow the steps below to

remove them. We recommend doing this

each time you change the detergent

1. Be sure to remove the water tank and

the appliance plug from the self‑

Be careful not to spill the cleaning

Removing the built-in rechargeable battery

Remove the built‑in rechargeable battery before disposing of

the shaver. Please make sure that the battery is disposed of at

an officially designated location if there is one. Do not

dismantle or replace the battery so that you can use the

shaver again. This could cause fire or an electric shock.

Replace it at an authorized service center.

Disconnect the power cord from the shaver when removing

Perform steps 1 to 4 and lift the battery, and then remove it.

For environmental protection and recycling of materials

This shaver contains a Lithium‑ion battery.

Please make sure that the battery is disposed of at an

officially assigned location, if there is one in your country.

Information for Users on Collection and Disposal of Old

Equipment and used Batteries

These symbols on the products, packaging, and/or

accompanying documents mean that used electrical

and electronic products and batteries should not be

mixed with general household waste.

For proper treatment, recovery and recycling of old

products and used batteries, please take them to

applicable collection points, in accordance with your

national legislation and the Directives 2002/96/EC and

By disposing of these products and batteries correctly,

you will help to save valuable resources and prevent

any potential negative effects on human health and the

environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and recycling of

old products and batteries, please contact your local

municipality, your waste disposal service or the point of

sale where you purchased the items.

Penalties may be applicable for incorrect disposal of

this waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic

equipment, please contact your dealer or supplier for

further information.

[Information on Disposal in other Countries outside the

These symbols are only valid in the European Union. If you wish to

discard these items, please contact your local authorities or dealer

and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In

this case it complies with the requirement set by the Directive for the

“Secar/Cargar” “Cargar”.

Luftbåren akustisk støj;

under barbering: 65 (dB (A) re 1 pW)

under trimning: 67 (dB (A) re 1 pW)

Coloque as 4 lâminas

as Directivas Europeias 2002/96/EC e 2006/66/EC.

Reservedeler for ES-LA93