iCLPTM3B03 - Flat screen mount Chief - Free user manual and instructions

USER MANUAL iCLPTM3B03 Chief

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief® and Centris™ are trademarks of Milestone AV Technologies. All rights reserved.

IMPORTANT WARNINGS AND CAUTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer's responsibility to make sure all components are properly assembled and installed using the instructions provided.

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8'' (15.9mm).

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the combined weight of all components attached does not exceed 125 lbs (56.7 kg) for the iCMPTM3 and iCLPTM3 or 175 lbs (79.4 kg) for the iCXPTM3. Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury.

AVISOS Y PRECAUCIONES IMPORANTES!

DIMENSIONS - iCMPTM3

DIMENSIONS - iCLPTM3

DIMENSIONS - iCXPTM3

Tighten Faserver
Apoptar elemento de fiascon	Stram fastspandingbeslag
Befestigungstaf festrochlen	Skiuva at tiske
Apoptar fixador	Krista klinnke
Serre il fissaggo	Dolegicl element mcucjagy
Bevestigung vostraiaian	Zajpjuu Zuvkojou
Serron les fixadons	Baglantnyi Sikspren
Coaware 3acteowy	Rogaló meghuzala
Lodon Fixerer
Atojer elemento de fixan	Lager fastspandingbeslag
Befostigungstaf lzen	Lasa fiste
Dasaportar fixador	Irotsa klinnke
Allentare il fissaggo	Poluzowac elementmojculagy
Bevestigung los daisen	Xahkupovn Zuvkojou
Dasemozlos fixadons	Baglantnyi Gavpatin
Ocnafuse 3acteowy	Rogaló hizilisa
Philips Screwdriver
Destor nilidor Philips	Sigemskuetoakher
Kruzschlitzschraubendhar	Kryskauwumeyal
Chave de fondas Philips	Ristpänuunvivain
Caudavite a stalla	Srubokraj Kryskalovy
Kruskaposdraevendraer	Kronopäg Philips
Toumevis a panta oncifomme	Philips Tornavida
Oraepna	Callagfej ciswerhráž
By Hand
Amano	Madhändon
Von Hand	Förhand
Cam a mão	Käsin
Amanoe	Reçnne
Mat de hand	Mio to xüp
Alamain	El be

	Pencil Mark
	Marcar com tapiz	Bya nirmarie
	Stiftmarkeinung	Pormmarkveuhr
	Marcar com tapis	Rimetti merita
	Segno a matta	Oznacranie okwiem
	Potoodemkraken	Izzydka iu okudji
	Marquage au crayon	Kalem larieni
	Mapka/Kaplanigaua	Ceruzajekliks
	Ort Hole
	Portar	Borehul
	Bedrioch	Bona hal
	Fazer furo	Porausniki
	Praticare un tro	Owdr wency
	Gat boren	Adroponi emirici
	Poroz un trou	Matkap Deligi
	Oraoepre Tpo-mipposen	Lyukuridis
	Adjust
	Ajuster	Juslar
	Einstellen	Juslara
	Ajuster	Statista
	Regolaro	Wyrregulowak
	Astatien	Pipocopyrj
	Ajuster	Ayar
	Flupconoco#ure	Balilhas
	Hex-Head Wrench
	Lave de caba hexagonal	Sekkurtet sieueneagle
	Sedskartanachloessel	Insoenyckel
	Chave de caba oseotavada	Kusikolokovain
	Chave esagonale	Kiust 2 ribam szadokatym
	Zeshantaleut	Khošć zojayunčić kajakci
	Clá-té tó hexagonale	Altgem Kafali (Allen) Anahtar

TOOLS REQUIRED FOR INSTALLATION

PARTS

C(1) [left upright]

For below kit, quantities are 4 of iCMPTM3, ICLPTM3 6 for iCXPTM3.

D(4 or 6) 5/16 x 2 1/2"

E(4 or 6) 1 / 4'' (6.4mm)

F(4 or 6) [concrete anchor]

G(1) Hardware Bag

GP(8) 1/4"(6.4mm)

GO(6) M8 x 50mm

GS(8) universal washer]

INSTALL WALL PLATE TO WALL - WOOD STUDS

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8'' (1.6cm).

1. Unfold wall plate (A) to prepare it for mounting to wall.
2. Level wall plate (A) and mark locations of pilot holes.

NOTE: The iCMPTM3 must be installed on two 16" studs. The iCLPTM3 can be installed on 16" studs (inner holes) or 24" studs (outer holes). For the iCXPTM3, it can be mounted over two or three 16" studs or two 24" studs. If mounting to three 16" studs, it must be mounted to all three studs using the outer holes and center holes.

NOTE: The vertical center of the display will be even with the center line indicated on the labels located directly below each hinge. Keep this in mind when determining mounting location.

1. Drill 7 / 32'' (5.5mm) diameter pilot holes into wood studs.
2. Using 1/2'' (12.7mm) wrench, install screws (D) through flat washers (E), wall plate (A) and into wood studs.

INSTALL WALL PLATE TO WALL - CONCRETE, CONCRETE BLOCK OR BRICK

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8'' (1.6cm).

WARNING: ELECTRICAL SHOCK HAZARD! CUTTING OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners.

WARNING: EXPLOSION AND FIRE HAZARD! CUTTING OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of gas, water, waste, or any other plumbing before cutting, drilling, or installing fasteners.

1. Unfold wall plate (A) to prepare it for mounting to wall.
2. Level wall plate (A) and mark locations of pilot holes at desired mounting location.

NOTE: For the iCLPTM3, either the inner or outer four holes may be used.

NOTE: For the iCXPTM3, use the outer four holes and the two middle holes on wall plate for installation.

NOTE: The vertical center of the display will be even with the center line indicated on the labels located directly below each hinge. Keep this in mind when determining mounting location.

1. Drill 5/16" (8mm) diameter pilot holes into wall at marked locations. Holes must be drilled at least 3-1/4 inches deep.
2. Install concrete anchors (F) into drilled holes. Use a hammer to tap anchors into holes.

IMPORTANT ! : The anchors must be installed through any wall covering until flush with the concrete wall.

1. Using 1/2'' (12.7mm) wrench, install screws (D) through flat washers (E), wall plate (A) and into concrete anchors (F).

INSTALL BRACKETS TO DISPLAY

WARNING: The minimum hole pattern size is 100mm× 100mm for the iCMPTM3 and 200mm× 200mm for the iCLPTM3 and the iCXPTM3.

1. Lay display face down on protective surface.

CAUTION: Using screws of improper diameter may damage your display! Proper screws will easily thread into display mounting holes.

1. Select screw diameter by examining hardware (GA-GO) (8mm, 6mm, 5mm, or 4mm) and comparing with mounting holes on display.

2. Select spacers:

3. If mounting holes are not recessed and both brackets (B and C) can lay flat against display, then no spacers are required.

4. If mounting holes are recessed, or if protrusions prevent brackets (B and C) from laying flat, then spacers (GP or GQ) must be used.

CAUTION: Using screws of improper length may damage your display! Proper screws will have adequate thread engagement without contacting bottom of display mounting holes.

1. Select screw length:

2. Using your hand, insert SHORTEST length screw of selected diameter (GA, GE, GI or GL) through brackets (B and C), universal washer (GS), selected spacer (GP or GQ, if required), into display mounting hole. Do NOT thread screw into hole at this time.

3. Proper screw length requires base of screw head to protrude above flat washer a distance equal to or greater than the screw diameter. If screw length is inadequate, select longer screw. Select shortest screw which will protrude the required distance.

4. Place brackets (B and C) on display, ensuring:

Upper hooks are towards top of display.
- Center of brackets (B and C) are as close to the center of the back of display as possible after being installed. Center of bracket is indicated by the diamond-shaped hole.

1. If installing display with wide hole pattern, it may be necessary to swap the uprights (B and C). See Switching Interface Brackets section for details.
2. Using Phillips screwdriver, carefully install selected screws through universal washers (GS), brackets (B and C), and spacers (GP or GQ, if required), into display.
3. Tighten all screws. Ensure all applicable display mounting holes (4, 6, or 8) are used.

INSTALL DISPLAY TO WALL PLATE

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the combined weight of all components attached does not exceed 125 lbs (56.7 kg) for the iCMPTM3 and iCLPTM3 or 175 lbs (79.4 kg) for the iCXPTM3. Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury.

WARNING: Display may be very heavy! Ensure display can be safely lifted and maneuvered as required to install on wall plate. Failure to take adequate precautions can result in serious personal injury or damage to equipment!

WARNING: Interface brackets must be hung on opposite sides of the center tab on wall plate!

1. Make sure interface brackets are in the kickstand position by pulling down on handles as far as possible.
2. Hang display with brackets (B and C) on upper rail of wall plate (A). Kickstand should be engaged with lower portion of wall plate.

NOTE: Any cable management or rear display adjustments should be made when the display is resting on the kickstand.

1. Unlock kickstand by pushing up on interface brackets until kickstand rests against the wall.
2. Push up on the interface brackets further in order to lock display into position against wall.
3. Straps can be tucked behind display on notch on interface brackets (B and C) after installation is complete so that they will not be visible to the viewer.
4. (Optional) Route padlock or cable lock (not included) through bottom holes on interface bracket to provide additional security.

4

Switching Interface Brackets (Optional)

For wide hole patterns, interface brackets must be reversed. See Table 1 below to determine if this is necessary.

Table 1: Hole Pattern Width

Model #	normal installation swap uprights
iCMPTM3 100-44	0mm 441-506mm
iCLPTM3 200-66	3mm 664-728.8mm
iCXPTM3 200-84	7mm 848-913mm

1. Remove the tilt tension knob, washer and screw from interface bracket.
   IMPORTANT ! : Hold the brackets steady when removing the knob, washer and screw from interface bracket to prevent internal washers from falling out. If internal washers do fall out, they must be reinserted in proper position before reinstalling knob on the other side!
2. Replace the knob, washer and screw in the opposite order.
3. Repeat for the other interface bracket.
4. Install interface brackets according to instructions in Section 2.

5

Tilt Adjustment

1. Adjust tilt tension adjustment knobs to desired tension.
2. Adjust tilt of display by pulling the top of display away from the wall until desired tilt position is reached.
3. Tighten tilt tension adjustment knobs to secure tilt position.

INSTALLACION DE LA PLACA DE PARED EN LA PARED: MONTANTES DE MADERA

INSTALLLEER HET SCHERM AAN DE WANDPLAAT

USA·8401 Eagle Creek Parkway, Suite 700·Savage, Minnesota 55378·800.572.1373

EMEA·[phone]

www.icmounts.com

©2012 Milestone AV Technologies. The iC Logo and StowAway are trademarks of Chief Manufacturing,

a products division of Milestone AV Technologies, a Duchossois Group Company. All rights reserved

Patents and patents pending. Milestone AV Technologies, Savage, MN 55378, USA

01/12

8800-002041 Rev 03