R95 - Electric razor REMINGTON - Free user manual and instructions

Product type	Electric shaver
Brand	REMINGTON
Model	R95
Power supply	AC adapter 100‑240 V, output 5 V DC, 1 A (models PA‑0510E/PA‑0510U)
Battery type	Built-in rechargeable battery
Battery life	Approximately 60 minutes of shaving
Charging time	24 h for first charge, then 24 h every 6 months; quick charge 5 min for 1 shave
Shaving head	Interchangeable foil and blades (replacement model SPF‑XF05)
Trimmer	Intercept pop-up trimmer
Hair reservoir	Integrated into the shaving head
Charge indicator	LED (model XF8505) or LED screen (model XF8705) with level display
Shower use	Yes, waterproof device (except charging base)
Cleaning	Rinse under running water after each use; do not use a brush on the foil
Included accessories	Charging base, AC adapter, protective cap, storage pouch
Trimmer adjustment	Button release, pop-up trimmer
Head replacement frequency	Every 6 months for optimal performance
Safety	Safety isolation adapter; do not use damaged device
Operating temperature	10 °C to 35 °C
Main material	Plastic and stainless steel (blades)
Warranty	Not specified in the manual

Frequently Asked Questions - R95 REMINGTON

How to charge the R95 shaver?

Make sure the device is off. Plug the charging base into the adapter and the mains. Place the shaver on the base, aligning the charging connectors. The first charge must last at least 24 h. The LED indicator or screen shows the charge level.

What is the battery life of the shaver?

Once fully charged, the shaver provides about 60 minutes of shaving. A quick charge of 5 minutes allows for 3 minutes of shaving.

Can I use the shaver in the shower?

Yes, the shaver is designed for shower use. However, the charging base must not be immersed or rinsed under water.

How to clean the shaver?

After each use, remove the shaving foil by pressing the release buttons. Shake off residues, then rinse the head under running water. Do not clean the foil with a brush. Then replace the head by pressing it down.

How to replace the foil and blades?

Detach the worn foil by pressing the release buttons. For the blade, hold it by the sides and pull upward. Position the new foil and snap it into place. Attach the new blade to the oscillator without touching the ends. Use the replacement model SPF‑XF05.

What to do if the shaver does not turn on?

If the battery is completely empty or if the device has not been used for a long time, perform a quick charge of 5 minutes. This should provide enough power for a 3 minute shave. If the problem persists, check the charging base connection.

How to use the pop-up trimmer?

Turn on the shaver, then press the unlock button of the trimmer to release it. Hold the trimmer at a right angle against the skin. To retract, slide the unlock button down and push the back of the trimmer until it clicks.

How often should the shaving heads be replaced?

Replace the foils and blades every 6 months to maintain optimal performance. Signs of wear include irritation, pulling, or blades visible through the foil.

Is the shaver compatible with all electrical voltages?

Yes, the adapter automatically adjusts to mains voltages from 100 V to 240 V, allowing use in many countries.

How to remove the battery for recycling?

Before disposal, disconnect the device. Open the back casing after removing a screw from the trimmer. Unscrew the 8 internal screws to access the battery. Cut the cables connecting the battery to the printed circuit board, then remove it. Dispose of the battery in accordance with local regulations.

USER MANUAL R95 REMINGTON

CaptureCut Foil Shaver

XF8505

XF8705

Thank you for buying your new Remington product. Please read these instructions carefully and keep them safe. Remove all packaging before use.

IMPORTANT SAFETY INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE OR INJURY TO PERSONS:

1 This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised/instructed and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised. Keep the appliance and cable out of reach of children under 8 years.
2 The adaptor contains a transformer. Do not cut off the adaptor to replace it with another plug, as this causes a hazardous situation.
3 Make sure the adaptor does not get wet.
4 Suitable for cleaning under an open water tap.
5 Always unplug the appliance before you clean it.
6 Suitable for use in a bath or shower.
7 Do not immerse the charging stand in water or any other liquid, nor rinse it under the tap.
8 Do not plug or unplug the appliance with wet hands.
9 Do not use the shaver, adaptor, charging stand or any other part if it is damaged, as this may cause injury. Always replace a damaged adaptor or charging stand with one of the original type.
10 Use, charge and store the appliance at a temperature between 10^ and 35^ .
11 Only use the adaptor, charging stand and accessories supplied.
12 Always put the protection cap on the product to protect the cutting heads when you are travelling.
13 Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Remington.
14 This appliance is not intended for commercial or salon use.
15 DThis appliance should be charged by approved safety isolating adaptors PA-0510E(K) with the output capacity of 5.0Vdc; 1.0A.

KEY FEATURES

1 On/off switch
2 Intercept trimmer
3 Shaving foils
4 Hair pocket
5 3 stage charge indicator (XF8505)
6 LED display (XF8705)
7 Charging pins (on back)

8 Pop-up trimmer (on back)
9 Head guard (not shown)
10 Foil assembly release buttons
11 Charging stand (not shown)
12 Adaptor (not shown)
13 Storage pouch (not shown)

GETTING STARTED

It is recommended that you use your new shaver daily for up to four weeks to allow time for your beard and skin to become accustomed to the new shaving system.

• Ensure the product is switched off.
• Connect the charging stand to the adaptor and then to the mains.
• Place the charge stand on a flat surface.
• Place the shaver in the charge stand with the charge pins contacting.
  Charge for at least 24 hours when using for the first time.
  XF8505: At low charge the LED indicator will flash rapidly. When charging the LED will flash slowly.
• When fully charged the LED will light solid for 1 minute and then turn off.
  XF8705: When charge is low 'Lo' will flash rapidly on the screen. When charging, the LED's flash in a clockwise rotation.
• When fully charged the minutes will flash 60 for 1 minute and then turn off.
• To preserve the life of your batteries, let them run out every 6 months then recharge for 24 hours.
• The appliance adapts automatically to a mains voltage between 100V and 240V.
• Quick charge feature: Your shaver is fitted with a 5 minute quick charge feature that will provide enough charge for 1 shave (3 minutes).

INSTRUCTIONS FOR USE

SHAVING

Make sure your shaver is properly charged.
- Switch the shaver on by pressing the on/off switch.
- Stretch the skin with your free hand so the hairs stand upright.
Hold the shaving head so that the foils touch your face.
Use short, linear strokes.

TRIMMING

• Switch the shaver on.
• Push the trimmer release button up to activate the trimmer.

• Hold the trimmer at a right angle to your skin.

• To retract the trimmer, slide the trimmer release button down and push the back of the trimmer head downwards until it locks into place.

TIPS FOR BEST RESULTS

Always hold the shaver at right angles to the skin so that all foils are touching the skin with equal pressure.
- Use moderate to slow stroking movements. The use of short circular motions in stubborn areas may obtain a closer shave, especially along the neck and chin line.
- DO NOT press hard against the skin in order to avoid damage to the foil heads.

Note: your shaver has been designed to be used in the shower if desired.

Care for your appliance to ensure a long lasting performance.
We recommend you clean your product after each use.
- The easiest and most hygienic way to clean the appliance is by rinsing the appliance head after use with warm water.
- Keep the switch in the "off" position when not in use.

CLEANING CAUTIONS

• Remove the foil assembly by pressing the release buttons on either side of the head and lifting the foil assembly upwards to remove from the hair pocket.
• Tap out the excess hair shavings and rinse the foils under running water.
• Do not clean the shaving foil with a brush.
• Replace the head assembly by placing the assembly on top of the hair pocket, press down and click into place.

\* CLEANING TRIMMER

• Lubricate the teeth of the trimmer every six months with a drop of sewing machine oil.

REPLACING THE FOILS & CUTTERS

• To ensure continued high quality performance from your shaver, we recommend the foils and cutters are replaced every six months.

Signs that your foils and cutters need replacing.

• Irritation: as foils get worn, you may experience skin irritation.

Pulling: as the cutters wear, your shave may not feel as close and you may feel the cutter pulling your hair.
- Wear through: you may notice that the cutters have worn through the foils.

TO REPLACE THE FOIL

• Remove the foil assembly by pressing the foil assembly release buttons on either side of the head and lifting the assembly upwards to remove from the hair pocket.
• Insert the new foil assembly on the hair pocket, press down and click into place.

REPLACING THE CUTTERS

• Grasp the cutter between your thumb and forefinger and pull upwards.
  Snap the new cutter into the oscillator tip.
  Note: DO NOT press on the cutter ends as this may cause damage.
• Foil head replacements can be found on the Remington website. Spare part number SPF-XF05

TROUBLESHOOTING

• If your shaver battery is completely empty or the shaver has not been used for an extended period of time, the shaver may not start when operated using the cord. If this occurs, a 5 minute quick charge will allow for 3 minutes of shaving.

BATTERY REMOVAL

The battery must be removed from the appliance before it is scrapped.
- The appliance must be disconnected from the supply mains when removing the battery.
- Slide the trimmer up to the open position and remove a single philips head screw.
Using a small flat screwdriver pry the back cover off the shaver.
- Using a philips screwdriver remove 8 screws to open the back of the internal housing.
- Remove and open the core from the shaver to expose the batteries.
- Cut the wire connecting the batteries to the circuit board and remove the batteries.
The battery is to be disposed of safely.

ENVIRONMENTAL PROTECTION

To avoid environmental and health problems due to hazardous substances in electrical and electronic goods, appliances marked with this symbol must not be disposed of with unsorted municipal waste, but recovered, reused or recycled.

UW APPARAAT VERZORGEN

REEMPLACEMENT DES LAMES

RADY, JAK OSIAGNAC NAJLEPSZY WYNIK

IOIACK HENCPABHOCTEIN

Ecn6aTapeB6pntbI pONHOCTbO pa3pRjEHa IIN6pNTBOB B TeUHe nIeNtBnHO BPemEH He NOp3bOaBnC, ee HEnb3B KBNoAub npn ONDKLIIOHcHOB M CbET bHype. B 3TOM cNyae 6bICTpa 3apJdA B TeUHe N5 MNHT PNOBNIIT 6pNTbC4 3 MNHybI.

N3BJIeUeHHe BATAPEI

• Pered ytunn3aunei 6aTapeu cneyu TnBLeyb n3 yCtpoNCTBa.
  -ПииИЗВLEЧЕНСБаТApEиУСТРОДСTOСLEДуETOTKЛЮЧИТБOT эльктрocети.
  IpeeBnHbTe TpMMep B OTKpbToe NOJIOKeHne N CHMNTe OINH C NOMObIo OTBepTKN C KpeToO6pa3HbIM IJIncem.
  C nOMOuMaJIeHbKo OTBepTKn NOIeHbTe 3aHIOU qAcTb KOpnyca.
  MaIenbKOJOTBepTKOICKpeTOO6pa3HbIMUINcEmOTKpyTnTe8BHTOB, TTo6blOTKpbTb3aHIOuCACTbBHyTpeneHeroKOpnyca.
• ɪЗвileкпгіеɪз 6рntbblɪ packpoitte 6aTapeHbɪŋ OTeK,чTo6bl nOlyuHTbdoCTyn K 6aTapeqM.
• 06pejIte npoOda, coeINHJIOJIe 6aTapeu c MoHTaxHOI pIaToI, n 3BLeKeITe 6aTapeu.
• Baatarpe noIopIexKNT 6e3onacHoi yTuIN3aun.

3KoIornuecka 3aunTa

Bo n36eJahne npOBeM c 3KoIogNei n 3OpOBbEm, Bbl3BaHHbIX BeueCTBaMn, COdepZaUIMNcB BJIeKTPnEeCKNX I JNEKTPOHHbIX yCTpoINCTBaX, YCTPOINCTBa, NOMEeHHbIe 3TmCnMBONOM, CJIeDyET yTNlN3PObAusbT OTeNbHO OTHecOPtNpOBaHHbIX 6bITOBbIX OTxOIOB; OHNI PNDJIeKATBOcCTaHOBJIeHIO, NOBTOPHOMY IcNOLb3OBaHIO IJI nepepa60Ke.

EN IYI SONUCLARICIN IPUCLARI

aalal alal alal alal alal alal alal

jia 1

glll lll glll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll

clll llll 1

cJyjlll j 100000000000000000000000000000000000000

J

auiui

aayyagll algal g aalall algal aalall ayaaal yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall

g jai jia jie jusui

aallll lllllllllllllllllllllllllllllllllllll

Ljulua Ubaia 1

gblall g 1s

a a a b b b b b b b b b b b b b

ailllll llll llll llll llll

aB

aaii jai i 1

a

aLusuul uus y Lueie "off" uus uus clll Juaal

aaii iiaaii iiaii

j 1

.

a a a a a a a a a a a a a a a a a a a a

aill

e 1

1

aaiiie aiae iiaiie iiaiiie

cbill

aall aal alal all

y

8

（） 9

S OBC = S COD + S BDO - S BOC

( 1 + u) + ·s + ( 1 + z) + ( 1 + 1) > 1 + z + 1 = 3 1 + z + 1 = 2z

(1) ( x,y) ( x,y - 1)

( A,B,E) ( D,E) 以 A 为直径的圆上

Jaeill

aaiy i aai j Jaaiaa aaii aaii aaii aaii aaii aaii

aill llll 1ie 2eill 3i, 4ii

Aaiy

julil

a 1

jua 1

aaii iiai iiai iiaii aie

oJyJy plznnn 1ie Jgle acl24 odJn

a:XF8500

.

aaiy

Remington® is a Registered Trade Mark of Spectrum Brands, Inc.,

or one of its subsidiaries

VARTA Consumer Batteries GmbH & Co. KGaA, Alfred-Krupp-Str. 9, 73479 Ellwangen,

Germany

www.remington-europe.com

© 2016 Spectrum Brands, Inc.