HSM 2686 - Hair clippers CLATRONIC - Free user manual and instructions

USER MANUAL HSM 2686 CLATRONIC

General Safety Instructions

GB

• Read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt and, if possible, the box with the internal packing.
• The appliance is designed exclusively for private use and for the envisaged purpose. This appliance is not fit for commercial use. Do not use it outdoors (except if it is designed to be used outdoors). Keep it away from sources of heat, direct sunlight, humidity (never dip it into any liquid) and sharp edges. Do not use the appliance with wet hands. If the appliance is humid or wet, unplug it immediately. Do not put it in water.
• When cleaning or putting it away, switch off the appliance and always pull out the plug from the socket (pull on the plug, not the cable) if the appliance is not being used and remove the attached accessories.
• Never leave the appliance unsupervised. To protect children from the dangers posed by electrical appliances, make sure that the cable is hanging low and that children do not have access to the appliance.
• Check the appliance and the cable for damage on a regular basis. Do not use the appliance if it is damaged.
• Do not try to repair the appliance on your own. Always contact an authorized technician. To avoid the exposure to danger, always have a faulty cable be replaced only by the manufacturer, by our customer service or by a qualified person and with a cable of the same type.
  Use only original spare parts.
• Pay careful attention to the following "Special Safety Instructions".

Special Safety Advice for this Machine

Only dry hair should be cut with this machine.
Only use the machine for cutting hair.
- Do not use the device near water (e.g. bathtubs, sinks or other containers filled with water).

Description of the Parts

1. Adjustment of the cutting length
2. On/off switch
3. Lower blade
4. Upper blade
5. Blade rail
6. Voltage adjustment (for mains operated machines)

7a-d. Cutting length accessories
7a. 3 mm
7b. 6 mm
7c. 9 mm
7d. 12 mm
8. Comb
9. Scissors
10. Blade oil
11. Brush

GB

Using the Machine

Fine Adjustment of the Voltage (Mains operated Machines)

In case of voltage fluctuations in the mains it may be necessary to adjust the machine. Switch the machine on. Turn the voltage adjustment screw (6) with a screwdriver or small coin so that the machine runs as quietly as possible.

Use with the Mains Adapter (Battery Machines)

Connect the machine to the mains adapter. Connect the device to a duly installed 230V/50Hz protective contact socket. The device can now also be used when the batteries are flat.

Charging the Battery

Before the machine can be used without a cord, the battery must be charged. Connect the AC adapter to the socket on the device's suspension eyelet and to a duly installed 230V/50Hz protective contact socket. The charge control lamp now illuminates. The first time charging will take approx. 12 hours; for subsequent charging will take approx. 5 hours. Then disconnect the mains adapter.

Preparing for Cutting

1. Briefly comb the hair.
2. Remove the blade protection.
3. Oil the blades slightly.
4. Place a cutting length guide suitable to the desired cutting length. If you are not sure of the cutting length, start from 12mm . Insert the blades in the slot and fit the attachment on the blade.
5. Insert the plug in a duly installed 230V/50Hz protective contact socket, switch on the device and run the device with the guide comb upwards and at a constant speed through your hair. The guide is held in a level position.

Cutting without Cutting Length Accessory

This is suitable for trimming the hair. The cutting length can be adjusted continuously in the range of approximately 0 - 1.2 mm.

For areas which are not accessible to the razor it is possible to use the scissors.

IMPORTANT: Do not use the device for more than 10 minutes. Allow the equipment to cool down for 10 minutes, before using it again.

Cleaning

• Disconnect the machine from the mains.
• Clean the device after use with a dry cloth. Then wipe off again with a dry cloth.
• The blades and accessories should be cleaned with the brush.

This device has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations.

Subject to technical changes without prior notice!

GB

Guarantee

The device supplied by our Company is covered by a 24 month guarantee starting on the date of purchase (receipt).

During the life of the guarantee any fault of the device or its accessories *) ascribable to material or manufacturing defects will be eliminated free of charge by repairing or, at our discretion, by replacing it. The guarantee services do not entail an extension of the life of the guarantee nor do they give rise to any right to a new guarantee!

Proof of the guarantee is provided by the proof of purchase. Without proof of purchase no free replacement or repair will be carried out.

If you wish to make a claim under the guarantee please return the entire machine in the original packaging to your dealer together with the receipt.

*) Damage to accessories does not mean automatic free replacement of the whole machine. In such cases please contact our hotline. Broken glass or breakage of plastic parts are always subject to a charge.

Defects to consumables or parts subject to wearing (e.g. motor pistons, kneading blades, drive shafts, spare remote control, spare toothbrushes, saw blades, etc.) as well as cleaning, maintenance or the replacement of said parts are not covered by the guarantee and hence are to be paid!

The guarantee lapses in case of unauthorized tampering.

After the expiry of the guarantee

After the expiry of the guarantee repairs can be carried by the competent dealer or repair service against the payment of the ensuing costs.

PL

Ipeed HOBbIM BKJIIOUeHHeM daIte emy 10 MInHyT OCTbITb.

Yxo3a np6opom