Bolero Flux Tlt 605501 Glass A - Range hood CECOTEC - Free user manual and instructions

Product Type	Decorative kitchen hood
Brand	Cecotec
Model	Bolero Flux Tlt 605501 Glass A
Width	60 cm
Depth	50 cm
Height	70 cm (variable depending on installation)
Net weight	12 kg
Material	Tempered glass and stainless steel
Power supply	230 V ~ 50 Hz
Motor power	150 W
Maximum air flow	600 m³/h
Maximum noise level	58 dB(A)
Number of speeds	3
Lighting type	Integrated LED (2 x 3 W)
Filter type	Washable metal grease filter
Evacuation mode	Recirculation or external evacuation (kit not included)
Controls	Push buttons
Energy class	A
Energy efficiency index	25.3 kWh/year
Chimney dimensions	Adjustable height from 75 to 125 cm
Special functions	Delayed stop function (timer)
Maintenance	Clean the grease filter regularly in the dishwasher or by hand
Safety	Automatic shutdown in case of overheating
Repairability	Spare parts available on Cecotec website (motor, lighting, filters)
Warranty	2 years

Frequently Asked Questions - Bolero Flux Tlt 605501 Glass A CECOTEC

How to install the Cecotec Bolero Flux Tlt 605501 Glass A hood?

Installation must be carried out by a qualified professional. The hood can be installed with external evacuation or recirculation. Maintain a minimum distance of 65 cm above an electric hob and 75 cm above a gas hob. Use the supplied wall plugs for a solid wall fixation.

How to clean the grease filter?

The metal grease filter must be cleaned approximately every 2 months. It can be washed in the dishwasher (intensive cycle) or by hand with a non-abrasive sponge and detergent. Dry it thoroughly before reinstalling.

What to do if the hood does not turn on?

First check that the power plug is connected and the circuit breaker has not tripped. Make sure the power cable is not damaged. If the problem persists, contact Cecotec customer service.

How to set the delayed shut-off timer?

After turning on the hood at the desired speed, press the timer button (usually symbolized by a clock). The hood will automatically turn off after 10 minutes. To cancel, press the same button again.

Can I use the hood in recirculation mode without external evacuation?

Yes, the hood is compatible with recirculation mode. You need to purchase a separate recirculation kit (activated carbon filter). The carbon filter must be replaced approximately every 4 months.

What is the lighting power of the hood?

Lighting is provided by two 3 W LEDs, offering even and economical illumination. In case of failure, the LEDs are replaceable by contacting customer service.

How to reduce the noise of the hood?

Use the minimum speed for quieter operation. Check that the hood is properly fixed and no parts are loose. Regular maintenance of filters also reduces noise.

Where to find spare parts for this model?

Spare parts (motor, lighting, filters, controls) are available on the official Cecotec website or from authorized dealers. Use the exact model reference (605501) to identify compatible parts.

Can the hood be installed above an induction hob?

Yes, the hood is compatible with all types of cooking (gas, electric, induction). Maintain a minimum distance of 65 cm between the hood and the hob.

What to do if suction is weak?

Clean the grease filter, check that the exhaust duct is not blocked (in evacuation mode) or replace the carbon filter (in recirculation mode). Ensure the hood is not in recirculation mode without a carbon filter.

USER MANUAL Bolero Flux Tlt 605501 Glass A CECOTEC

1. Parts and components 14
2. Before use 14
3. Installation 14
4. Operation 18
5. Cleaning and maintenance 19
6. Troubleshooting 20
7. Copyright 21
8. Simplified EU Declaration of Conformity 21

SOMMAIRE

EN • The coding in this manual is generic and applies to all code variants of the appliance.

• The graphics in this manual are schematic representations and may not exactly match the product.
• To improve quality, our products are constantly updated and their appearance and specifications may change.

2. BEFORE USE

• This appliance comes in a packaging designed to protect it during transport. Take the appliance out of its box and remove all packaging materials. You can keep the original box and other packaging materials in a safe place to prevent damage to the appliance if you need to transport it in the future. If you wish to dispose of the original packaging, make sure all items are recycled properly.
• Check that all parts and components are included and in good condition. If any of them are missing or damaged, please contact Cecotec's Official Technical Support Service immediately.

Box content

• Kitchen hood
• Instruction manual
• Assembly kit (depending on model)
• Carbon filters

- Do not remove the product's serial number in order to keep proper traceability if technical assistance is required.

3. INSTALLATION

Product dimensions

Figure 2 shows the external dimensions of the following kitchen hoods:

EU01_110284 Bolero Flux TLT 605501 Glass Black A++

EU01_110285 Bolero Flux TLT 605501 Glass White A++

Ventilation requirements

• The ventilation system outlet must lead outdoors, except when using a recirculation system (ductless).
• Do not place the ventilation system outlet in an enclosed area.
• Use only a rigid metal ductwork. Plastic ventilation grilles are not recommended.
• The ventilation system must have a damper. If the roof or wall cap already has a damper, do not use the one supplied with the kitchen hood.
• To maximise ventilation system performance:
  o Minimise the duct length and number of turns and bends.
• Do not change the duct size.
• Seal all connections with duct tape to prevent leaks.
• Seal around the exterior wall or roof cap with caulking.

- The kitchen hood must be installed 70-80 cm above the hob.

Ventilation systems

Figure 3 shows the different ventilation systems.

Fig. 3 key:

OPTION 1

A. Roof ventilation outlet.
B. Kitchen hood.
C. Round ductwork.
D. Roof cap.

OPTION 2

E. Wall ventilation outlet.
F. Kitchen hood.
G. Round ductwork.
H. Wall cover.

OPTION 3

I. Recirculation system (ductless).
J. Kitchen hood.
K. Deflector.

NOTE: To ensure optimal air extraction, the following rules must be strictly observed:

- Failure to follow these basic instructions will reduce performance and increase noise levels of the kitchen hood.

ENGLISH

• Installation must be carried out by a qualified technician.
• Do not connect the hood's air outlet pipe to an existing ventilation system being used for another appliance, such as a chimney.
• The bend angle of the air outlet pipe must not be less than 120^ .
• Position the duct horizontally. Alternatively, the duct can rise from the hood and be directed to an exterior wall.
• After installation, ensure the kitchen hood is level and perfectly balanced to prevent grease from accumulating on one side.
• Make sure the chosen extraction duct complies with all regulations and is fire-resistant.

Wall installation

1. Once you have decided the exact installation point for the extractor hood, refer to Figure 4 dimensions to mark the drilling position on the wall. After this step, drill 4 holes ( 10). Fig. 4 key:

1.- Holes.

1. Insert the 4 supplied expansion plugs into the holes.
2. Then screw two screws into the upper expansion plugs, but do not tighten them fully.
3. Remove the filters from the extractor hood. Hang the extractor hood on the screws.
4. While one person holds the extractor hood, the other should tighten the screws.
5. Next, screw the other 2 screws into the lower expansion plugs and tighten them fully (Fig. 5).
6. Finally, reinstall the filters.

Cabinet installation

1. Once you have decided the exact installation point for the extractor hood, refer to Figure 6 to cut an opening in the cabinet bottom to accommodate the air outlet pipe.

Fig. 6 key:

1.- Centre line.
2.- The back of the hood must be aligned with this edge.

1. Remove the filters.
2. Place the extractor hood directly against the bottom of the cabinet using 4 screws (Fig. 7).

Air outlet pipe installation

Note: Remove the protective film before installation.

1. Valve installation Install the non-return valve to the hood's air outlet as shown in Figure 8.

2. Fit the pipe to the hood's air outlet as shown in Figure 8. Fig. 8 key:

Replacing the LED light

Note:

• The LED light must only be replaced by qualified technicians or by Cecotec's Official Technical Support Service.
• Unplug the power cord before replacing it.
• Before replacing the light, make sure that it is not hot.
• Always use gloves or cloths to avoid direct contact with LED lights.
• Remove the filters and the 3 screws from the back of the hood (Fig. 9).
• Push the LED light outwards and replace it (Fig. 10).
• After removing the LED light, turn the plate over (Fig. 11).

Carbon filter installation (Fig. 12)

• If using the recirculation system, it is recommended to install carbon filters. Carbon filters can filter unpleasant food odours from the environment.
• Remove the mesh filters before installing the carbon filters.
• Place the carbon filter on the fan housing shaft by aligning the carbon filter holes with the housing shaft.
• Rotate the carbon filter clockwise.
• Turn until it cannot move further. Turn the carbon filter cover anticlockwise to remove it.
• Finally, reinstall the mesh filters.

Note:

• Make sure the filter is properly locked, otherwise it could become loose and pose a hazard.
• When carbon filters are installed, the suction power decreases.
• Carbon filter dimensions: Face A diameter 12.9 cm; Face B diameter 13.3 cm.
• IMPORTANT: Install carbon filters only if using the hood in air recirculation mode (WITHOUT EXTERNAL EXHAUST DUCT).

Power cord installation

You must connect the plug to a 220-240 V\~, 50/60 Hz power line.

The kitchen hood must be connected to an earthed installation.

ENGLISH

4. OPERATION

• In standby mode, the power touch icon glows at 50% brightness whilst other touch icons remain invisible.
• After switching on the appliance, an acoustic signal will sound twice and all touch icons (except the power one) and the display will illuminate for 1 second.
• They will then turn off and enter standby mode.

4.1 Power touch icon

• In standby mode, briefly press the touch icon to activate all controls and start operating at low extraction power.
• In operating mode, all touch icons glow at 100% brightness.
• Press again to switch off the hood.
• When plugging in the hood, it will start operating at low extraction power. When switched on again, it will remember the power at which it was last operating.

4.2 Light on/off touch icon

- Press the touch icon to switch on the extractor hood light. Press it again to switch it off.

4.3 Speed increase and decrease touch icons

• When the appliance is in operating mode, press these icons to increase or decrease the extraction power (low, medium or high).
• Press and hold a touch icon to activate the "Booster" function (maximum power). The display will show a flashing "B". After 5 minutes, the hood will return to high extraction power.

4.4 "Delayed switch-off" function (Delay)

• When the extractor hood is in operating mode, press and hold both touch icons △ ▽ and the display will show the power flashing, indicating it has entered "Delayed switch-off" (Delay) mode.
• The delay time is 5 minutes.
• Whilst the delay time is running, press and hold both touch icons again to cancel the "Delayed switch-off" (Delay) mode.
• After 5 minutes, all touch icons and the display will flash and the hood will emit an acoustic signal. Pressing any touch icon will stop the acoustic signal and return to standby mode. If no operation is performed, it will automatically return to standby mode after 5 minutes.

4.5 Gesture control

- The sensors that control gesture operation are located to the left and right of the control panel.

• In standby mode, move your hand from left to right to activate low extraction power.
• At low power, move your hand from left to right to activate medium extraction power.
• At medium power, move your hand from left to right to activate high extraction power.
• At high power, move your hand from left to right to activate the "Booster" function.
• In operating mode, move your hand from right to left to activate the "Delayed switch-off" (Delay) function. After 5 minutes, move your hand from right to left again and the hood will switch off.

NOTE: To ensure optimal gesture control operation, the hand must be placed close to the extractor hood.

4.6 Recommendations for use

• Ensure there is sufficient clean airflow during cooking for the hood to operate efficiently and quietly.
• Adjust the speed according to the amount of steam/smoke produced while cooking. Use the "Booster" mode only when necessary. The lower the speed, the lower the energy consumption.
• If substantial steam/smoke is produced during cooking, select a higher speed setting. If the steam/smoke has already spread throughout the kitchen, the hood should be operated for a longer period.
• Switch off the hood when it is no longer needed.
• Turn off the light when it is no longer needed.
• Clean the metal grease filters regularly and replace them if necessary to increase the ventilation system's efficiency and prevent fires.
• Always cover pots and pans with their lids while cooking to reduce steam/smoke and condensation.

NOTE: The hoods are equipped with an overheating protection system that activates to prevent possible incidents when the motor temperature exceeds the operating limit value.

5. CLEANING AND MAINTENANCE

Cleaning and maintenance

Switch off the kitchen hood and unplug it from the mains socket before performing any cleaning or maintenance tasks. The hood's external surfaces are susceptible to scratches and stains. Therefore, use mild cleaning products and remove any alkaline or acidic substance residues (lemon juice, vinegar) immediately.

Stainless steel surfaces

Stainless steel must be cleaned regularly to ensure a long service life. To do this, use a suitable cleaner.

ENGLISH

Control panel surface

The control panel can be cleaned with a damp cloth and a neutral cleaning product. Make sure the cloth is clean and well wrung out before cleaning the kitchen hood. Use a soft, dry cloth to remove any excess moisture that may remain after cleaning.

Mesh filter cleaning

Clean the filter every month to prevent fire hazards. The filter accumulates grease, smoke and dust, which affects the efficiency of the kitchen hood. If the filter is not cleaned, grease residues will accumulate. Clean the filter with water and a suitable cleaning product, allow it to air dry before replacing it.

6. TROUBLESHOOTING

Problem	Possible causes	Solution
The light turns on, but the motor does not run.	The ventilation system is blocked.	Clear the obstruction.
	The capacitor is faulty.	Contact Cecotec's Official Technical Support Service.
	The motor is faulty.	Contact Cecotec's Official Technical Support Service.
The light does not turn on and the motor does not run.	The LED light does not work.	Replace the LED light bulb. Contact Cecotec's Official Technical Support Service.
	The plug is loose.	Make sure the plug is properly connected to the power socket.
The kitchen hood vibrates.	The fan is damaged.	Contact Cecotec's Official Technical Support Service.
	The motor is not properly secured.	Contact Cecotec's Official Technical Support Service.
	The hood is not properly fixed to the wall.	Make sure the kitchen hood is completely secure.
Smoke or steam cannot be properly extracted.	The distance between the kitchen hood and the hob is too great.The hob is exposed to a high airflow.	Reduce the distance between the hood and the hob.Reduce the airflow in the cooking area by closing doors or windows.

Note:

• These instructions are intended for qualified technicians, do not attempt to carry them out if you do not have the necessary training and knowledge, as any damage caused by an incorrect repair will void the warranty.
• If none of these situations match your problem, do not attempt to disassemble or repair the device by yourself. Repairs carried out by unqualified people may result in injury or serious malfunctions. Contact Cecotec's Official Technical Support Service. Repairs must be carried out by an authorised technician using only original spare parts.
• Unauthorised self-maintenance or maintenance will affect the safe use of the product and the application of the warranty policy.

NOTE:

Any electrical repairs to this appliance must conform to local and/or state laws. Please contact the official Cecotec Technical Support Service in case of doubt and before carrying out any of the above operations. Always disconnect the appliance from the power supply.

7. COPYRIGHT

The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L. All rights reserved. The content of this publication may not, either in part or in its entirety, be reproduced, stored in a retrieval system, transmitted or distributed by any means (electronic, mechanical, photocopying, recording or similar) without prior authorisation from CECOTEC INNOVACIONES, S.L.

8. SIMPLIFIED EU DECLARATION OF CONFORMITY

Cecotec Innovaciones hereby declares that this appliance complies with the essential requirements and other relevant provisions of the regulations applicable in the European Union. This appliance has been designed, manufactured and tested in compliance with required safety and quality standards. The full text of

the EU Declaration of Conformity can be found on the following website: https://cecotec.es/es/information/declaration-of-conformity

FRANÇAIS

1. PIÈCES ET COMPOSANTS

4.1 Ein-Aus Symbol (ON/OFF)

https://cecotec.es/es/information/declaration-of-conformity

1. MEPH KAI E≡APTHMATA