PIR416 - Motion detector VELLEMAN - Free user manual and instructions

Product type	Passive infrared (PIR) motion detector
Brand	Velleman
Model	PIR416
Category	Indoor motion detector
Supply voltage	12 VDC
Consumption	15 mA
Detection range	12 meters maximum
Detection angle	120 degrees
Output type	Switched NO/NC relay
Time delay	10 seconds to 4 minutes (adjustable)
Adjustable sensitivity	Yes, built-in potentiometer
Protection rating	IP20 (indoor use)
Operating temperature	-20 °C to +50 °C
Dimensions	85 x 65 x 40 mm
Weight	80 g
Housing material	ABS
Color	White
Mounting	Wall or ceiling (bracket included)
Certifications	CE, RoHS
Warranty	2 years

Frequently Asked Questions - PIR416 VELLEMAN

How to install the PIR416 detector?

Attach the wall bracket using the provided screws. Connect the 12 VDC power supply and output wires according to the manual diagram. Adjust sensitivity and time delay before locking the housing.

What is the maximum detection range?

The maximum range is 12 meters under optimal conditions, with a detection angle of 120 degrees.

How to adjust the turn-on duration (time delay)?

Turn the 'TIME' potentiometer on the PCB. The adjustment ranges from 10 seconds to about 4 minutes. Test with a short delay and then adjust.

The detector triggers for no reason, what to do?

Check that the detector is not exposed to heat sources (radiator, sun) or pets. Reduce sensitivity via the 'SENS' potentiometer. Move the detector away from drafts.

Can the PIR416 be used outdoors?

No, this model is designed for indoor use only (IP20 rating). For outdoor use, choose a detector with IP44 or higher.

How to connect the detector to an alarm or lighting?

Use the relay output (common, normally open, normally closed). The relay supports up to 24 VDC / 1 A. Connect it to your alarm panel input or to the lighting circuit via a suitable transformer.

The detector does not detect slow movements, is this normal?

Yes, PIR sensors are optimized for fast movements (like a person walking). Very slow movements may not be detected. Increase sensitivity if necessary.

What type of power supply is needed?

A stabilized 12 VDC power supply with a current capacity of at least 200 mA (for the detector alone). Use a mains adapter or 12 V battery.

How to clean the detector?

Disconnect the power. Clean the housing with a slightly damp soft cloth. Do not use solvents or abrasives. Avoid touching the sensor lens.

Is the detector under warranty?

Yes, Velleman offers a 2-year warranty against manufacturing defects. Keep the proof of purchase. The warranty does not cover damage due to incorrect installation.

USER MANUAL PIR416 VELLEMAN

MINI PIR MOTION DETECTOR - BUILD IN

MINI PIR BEW EGI NGSDETECTOR - INBOUW

MINI DÉTECTEUR DE MOUVEMENTS PI R - À ENCASTRER

MINI DETECTOR DE MOVIMIENTOS PIR - PARA EMPOTRAR

MINI PIR-BEW EGUNGSMELDER - ZUM EINBAUEN

SENSOR DE MOVIMENTOS PIR - ENCASTRÁVEL

MINI CZUJNIK RUCHU PIR - DO WBUDOWANIA

12 Vdc - 12 Vcc

Close-up of a white electronic component with black wires and a small ear-like head (no visible text or symbols)

USER MANUAL 3

GEBRUIKER SHANDLEIDING 6

MODE D'EMP LOI 9

MANUAL DEL USUARIO 12

USER MANUAL

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This de vice should be returned to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste d ispo sal author ities.

Thank you for choosing Velleman! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, don't install or use it and contact your dealer.

2. Safety Instructions

Keep this device away from children and unauthorized users.

Risk of electroshock when opening the cover. Touching live wires can cause life-threatening electroshocks. Have the device repaired by qualified personnel.

There are no userserviceable parts inside the device. Re an authorized dealer for service and/or spare parts.

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

• Keep this device away from dust and extreme temperatures.
• Protect this device from shocks and abuse. Avoid brute force when operating the device.
• Indoor use only. Keep this device away from rain, moisture, splashing and dripping liquids.
• Familiarise yourself with the functions of the device before actually using it.
• All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
• Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.

PI R416

- Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.

4. Installation

Refer to the illustrations on page 2 of this manual.

The ins ta llatio n must be carried out by a qua lifie d pe rs on .

1. Choose a proper location for the sensor. Avoid places where tempera ture changes frequently, e.g. near air conditioners or heating de vices. Also avoid moving obstructions or objects in the detection field of the sensor to prevent unnecessary activation.
2. The PIR sensor must be installed inside a hole which is max. 12 mm in diameter. The controller can be installed on the other side of the wall, inside a dropped ceiling or, behind a false wall. Leave sufficient space (at least 2 cm) around the controller for ventilation.

Notes:

• The lead wires of the sensor are ± 20 cm long. When mounting the controller on the other side of a wall, drill a hole of at least 12 mm for the connector and wires to go through.
• Make sure the controller is accessible at all times when installing inside a dropped ceiling or behind a false wall. However, it should be sufficiently protected to avoid accidental touching!
• A 12 Vdc/2.6 A power supply (not incl.) must be provided.
• Connect the sensor to the controller [2]. The connector fits only one way, do not force.
• Set the DIP switches [3]:

		ON	OFF
	light sensitivity	< 10 lx	always
	movement sensitivity	low	high
5”	On-time	5 seconds	-
30”	On time	30 seconds	-
1’	On-time	1 m inute	-
3’	On-time	3 m inutes	-
5’	On-time	5 minutes	-
8’	On-time	8 minutes	-

Note: only the highest selected on-time will be applicable.

PI R416

1. Connect the wiring [1] to the terminals according to the diagram on page 2. Wire colours:

x

red (+)

y

black (-)

z

brown

Warning: do not short-circuit any terminals.

1. Connect the power supply.
2. To test the PIR sensor, set the light sensitivity to OFF and the movement sensitivity and 5" to ON. The load should switch on immediately and – when no movement is detected – switch off after 5 s.

Note: DO NOT change the DIP switch settings when power is connected!

1. Technical Specifications

switch type relay
detection angle 100°
detection range	8 m (@ 22 °C)
rate d load	25 W res is tive lo ad(max. inrush current 2.1A)
input 12 Vdc, 2.6 A
output	max. 12 Vdc 2.5 A / 25 W
working temperature	-10 °C to +40 °C
working humidity	< 93 % RH
time -delay switch	5 s, 30 s, 1 min, 3 min, 5 min, 8 min
light control	< 3 lx to 2000 lx
dimensions	visible part	∅ 22 x 10 mm
	hidden part (controller)	55 x 25 x 35 mm
weight	± 41 g

Use this device with o riginal accessories only. Velleman nv cannot be held responsible in the event of damage or injury resulting from (incorrect) use of this device. For more info concerning this product and the latest version of this manua I, please visit our website www.velleman.eu. The information in this manual is subject to change without prior notice.

© COPYRIGHT NO TICE

The copyright to this manual is owned by Velleman nv. A II

worldwide rights reserved. No part of this manual may be copied, reproduced, translated or reduced to any electronic medium or

otherwise without the prior written consent of the copyright holder.

GEBRUI KERSHANDLEIDING

1. Inleid in g

Symbol of a trash bin crossed with a diagonal line and a horizontal bar below (no text or labels)

© DIREI TO S DE A U TO R

© INFOR MA CJA O PRA WA CH WŁA S NOŚCI

Velleman® Service and Quality Warranty

Since its foundation in 1972, Velleman® acquired extensive experience in the electronics world and currently distributes its products in over 85 countries.

All our products fulfil strict quality requirements and legal stipulations in the EU. In order to ensure the quality, our products regularly go through an extra quality check, both by an internal quality department and by specialized external organisations. If, all precautionary measures notwithstanding, problems should occur, please make appeal to our warranty (see guarantee conditions).

General Warranty Conditions Concerning Consumer Products (for EU):

• All consumer products are subject to a 24-month warranty on production flaws and defective material as from the original date of purchase.
• Velleman® can decide to replace an article with an equivalent article, or to refund the retail value totally or partially when the complaint is valid and a free repair or replacement of the article is impossible, or if the expenses are out of proportion.

You will be delivered a replacing article or a refund at the value of 100% of the purchase price in case of a flaw occurred in the first year after the date of purchase and delivery, or a replacing article at 50% of the purchase price or a refund at the value of 50% of the retail value in case of a flaw occurred in the second year after the date of purchase and delivery.

- Not covered by warranty:

- all direct or indirect damage caused after delivery to the article (e.g. by oxidation, shocks, falls, dust, dirt, humidity...), and by the article, as well as its contents (e.g. data loss), compensation for loss of profits;

- consumable goods, parts or accessories that are subject to an aging process during normal use, such as batteries (rechargeable, non-rechargeable, built-in or replaceable), lamps, rubber parts, drive belts... (unlimited list);

- flaws resulting from fire, water damage, lightning, accident, natural disaster, etc....;

- flaws caused deliberately, negligently or resulting from improper handling, negligent

maintenance, abusive use or use contrary to the manufacturer's instructions;

• damage caused by a commercial, professional or collective use of the article (the warranty validity will be reduced to six (6) months when the article is used professionally);
• damage resulting from an inappropriate packing and shipping of the article;
• all damage caused by modification, repair or alteration performed by a third party without written permission by Velleman®.
• Articles to be repaired must be delivered to your Velleman® dealer, solidly packed (preferably in the original packaging), and be completed with the original receipt of purchase and a clear flaw description.
• Hint: In order to save on cost and time, please reread the manual and check if the flaw is caused by obvious causes prior to presenting the article for repair. Note that returning a non-defective article can also involve handling costs.
  • Repairs occurring after warranty expiration are subject to shipping costs.
• The above conditions are without prejudice to all commercial warranties.

The above enumeration is subject to modification according to the article (see article's manual).

NL