Wake-up Light HF3470 - Light therapy PHILIPS - Free user manual and instructions

Product Type	Light therapy alarm clock
Model	Wake-up Light HF3470
Brand	Philips
Dimensions (approx)	22 x 11 x 17 cm
Weight	1 kg
Power Supply	AC adapter 12V, 1A
Light Source	LED lamp, non-replaceable
Brightness Levels	20
Maximum Illuminance	300 lux at 20 cm
Color Temperature	Simulated sunrise (warm to cool)
Alarm Sounds	5 (nature sounds, radio, etc.)
Radio	FM radio with preset stations
Snooze Duration	9 minutes
Light Therapy Mode	Yes, adjustable duration (15-60 min)
Display	Digital, white LED
Cleaning	Wipe with damp cloth; do not use abrasive cleaners
Safety	Low voltage, overheat protection
Spare Parts	AC adapter (optional); lamp not user-replaceable
Warranty	2 years (depending on region)
Manual Languages	Multiple (including EN)

Frequently Asked Questions - Wake-up Light HF3470 PHILIPS

How do I set the alarm on the Philips Wake-up Light HF3470?

Press the Alarm button, then use +/- to set the alarm time. Press the Alarm button again to confirm. You can also choose the alarm sound and light brightness.

Can I use the light therapy feature without setting an alarm?

Yes. Press the Light button to manually turn on the light. You can adjust brightness with the +/- buttons. To use light therapy mode, press the Therapy button and set the duration.

How do I adjust the brightness of the simulation light?

During sunrise simulation, you can adjust the brightness by pressing the +/- buttons. For manual light, press the Light button and then adjust.

What should I do if the device does not turn on?

Check that the power adapter is fully plugged into the device and the wall outlet. Ensure the outlet is working. If it still doesn't turn on, try a different outlet or contact Philips support.

How do I clean the Wake-up Light?

Unplug the device. Use a soft, damp cloth to wipe the exterior. Do not use any abrasive cleaners or allow moisture to enter the openings. Do not immerse in water.

Does the HF3470 have a radio?

Yes, it has an FM radio. Press the Radio button to turn it on, and use the +/- buttons to tune stations. You can save presets by holding the Preset button.

How do I set the time on the display?

Press and hold the Time button until the hour flashes. Use +/- to set the hour, then press Time again to set minutes. Finally, press Time to confirm.

Can I replace the light bulb or LED?

The LED lamp is not user-replaceable. If the light fails, please contact Philips customer service for assistance. Do not attempt to open the device.

What is the purpose of the snooze function?

Snooze delays the alarm for 9 minutes. Press the Snooze bar on top of the device when the alarm sounds. It can be used multiple times.

How do I reset the device to factory settings?

To reset, press and hold the Alarm and Light buttons simultaneously for 5 seconds. The display will flash and then return to default settings.

USER MANUAL Wake-up Light HF3470 PHILIPS

White portable kitchen appliance with a digital display and control panel (no visible text or symbols)

Diagram of three open panels with grid patterns and curved arrows indicating rotation or movement (no text or symbols)

ENGLISH 6

БЪЛГАРСКИ 14

ČEŠTINA 23

EESTI 31

HRVATSKI 39

MAGYAR 47

КАЗАКША 55

LIETUVIŠKAI 63

LATVIEŠU 71

POLSKI 79

ROMÂNĂ 87

РУССКИЙ 95

SLOVENSKY 104

SLOVENŠČINA 112

SRPSKI 120

УКРАЇНСЬКА 128

Introduction

Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.

The Philips Wake-up Light helps you wake up more pleasantly. The light intensity of the lamp gradually increases to the set level in the 30 minutes before the set wake-up time. The light gently prepares your body for waking up at the set time. To make waking up an even more pleasant experience, you can use natural wake-up sounds or the FM radio (HF3470 only).

The effects of the Wake-up Light

The Philips Wake-up Light gently prepares your body for waking up during the last half hour of sleep. In the early morning hours our eyes are more sensitive to light than when we are awake. During that period the relatively low light levels of a simulated natural sunrise prepare our body for waking up and getting alert. People who use the Wake-up Light wake up more easily, have a better overall mood in the morning and feel more energetic. Because the sensitivity to light differs per person, you can set the light intensity of your Wake-up Light to a level that matches your light sensitivity for an optimal start of the day.

For more information about the Wake-up Light, see www.philips.com.

General description (Fig. 1)

A Vents
B Lamp housing
C Mains cord
D Antenna
E Display
1 Hour indication of clock time/alarm time
2 Clock time symbol
3 Alarm symbol
4 Radio symbol (HF3470 only)
5 'Birds' sound symbol (HF3470 only)
6 'Beep' sound symbol
7 Display brightness symbol
8 Sound level symbol
9 Radio frequency symbol (HF3470 only)
10 Light symbol
F Menu '-' button
G MENU button
H SELECT button
I Menu '+' button
J Control lever with 'alarm off', 'alarm on' and 'snooze' positions
K Buttons on the side of the appliance
1 Light intensity '+' button
2 Light on/off button
3 Light intensity '-' button
4 Volume increase button
5 Radio on/off button (HF3470 only)
6 Volume decrease button

Important

• Read this user manual carefully before you use the appliance and save it for future reference.
• This appliance is double insulated according to Class II (Fig. 2).

Danger

• Water and electricity are a dangerous combination. Do not use this appliance in wet surroundings (e.g. in the bathroom or near a shower or swimming pool).
• Do not let water run into the appliance or spill water onto the appliance (Fig. 3).

Warning

• Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance.
• The appliance is suitable for mains voltages of 230V and frequencies of 50Hz.
• If the mains cord is damaged, you must have it replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard.
• Always let the appliance cool down for approx. 15 minutes before you open the top cap to remove the lamp. The lamp and the metal part of the top cover become hot during use and you may burn your fingers when you touch them. (Fig. 4)
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is for indoor use only (Fig. 5).

Caution

• Do not drop the appliance or expose it to heavy shocks.
• Place the appliance on a stable, level and non-slippery surface.
• Do not use the appliance at room temperatures lower than 10^ C or higher than 35^ C.
• Make sure the vents in the top and in the bottom of the appliance remain open during use.
• Never use the appliance if the lamp housing or top cover is damaged, broken or missing.
• Consult your doctor before you start using the appliance if you have suffered from or are suffering from serious depression.
• Do not use this appliance as a means to reduce your hours of sleep. The purpose of this appliance is to help you wake up more easily. It does not diminish your need for sleep.
• The appliance has no on/off switch. To disconnect the appliance from the mains, remove the plug from the wall socket.
• This appliance is only intended for household use, including similar use for instance in hotels.

General

• This appliance allows you to choose the light intensity level you want to wake up to (see section 'Using the lamp', chapter 'Using the appliance').
• If you often wake up too early or with a headache, reduce the light level.
• If you share a bedroom with someone else, this person may unintentionally wake up from the light of the appliance, even though this person is further removed from the appliance. This phenomenon is the result of differences in light sensitivity between people.

Electromagnetic fields (EMF)

This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today.

Preparing for use

Setting the clock

1 Put the plug in the wall socket.
The hour indication on the display starts flashing to indicate that you have to set the clock time (Fig. 6).
2 Press the menu + or - button to set the hour.

Note: You can only do this when you are in the set clock menu and when the hour indication flashes. If this is not the case, press the MENU button, use the menu + or - button to select the set clock menu and press the SELECT button to confirm. You are now in the set clock menu.

3 Press the SELECT button to confirm.

The minute indication starts flashing (Fig. 7).

4 Press the menu + or - button to set the minutes.

5 Press the SELECT button to confirm.

The appliance leaves the menu and the display shows the set clock time.

The appliance is now ready for use.

Note: Every time you remove the plug from the wall socket for more than approximately 15 minutes, you have to set the clock time again in the way described above. To change the set clock time when the plug is still in the wall socket, see section ‘Menu functions’ in chapter ‘Using the appliance’.

Using the appliance

Menu functions

Below you find a description of all functions that can be set in the menu. These functions appear in the menu in the following order:

• Clock time
• Alarm time
• Alarm sound (HF3470 only)
• Display brightness: You can choose a display brightness between 1 and 4.
  You can set the menu functions in the following way:

1 Press the MENU button to enter the menu (Fig. 8).
2 Press the menu + or - button to select a function. (Fig. 9)
3 Press the SELECT button to enter this function (Fig. 10).
4 Press the menu + or - button to change a setting. (Fig. 9)
5 Press the SELECT button to confirm (Fig. 10).

Using the lamp

You can use the appliance as a bedside lamp.

1 To switch on the lamp, press the lamp on/off button. (Fig. 11)
2 Press the light intensity + and - buttons to select a light intensity (Fig. 12).

You can choose a light intensity between 1 and 20.

Note: It takes approx. 1 second for the lamp to go on. This is normal, the lamp needs to heat up.

Note: The light intensity you have selected is automatically set as the light intensity level for the alarm as well.

Tip: When you use the appliance for the first time, set the light intensity to 20. The moment you wake up, check which light intensity level the appliance has reached by briefly pressing the light intensity + or - button. When you do this, the current alarm light intensity level appears on the display. Set the alarm light intensity to this level for the next day.

3 To switch off the lamp, press the lamp on/off button again.

Setting the alarm

When you set the alarm, you choose an alarm time and (only in case of HF3470) the type of sound you want to wake up to. The alarm is set when the alarm symbol is visible on the display. The light intensity slowly increases to the selected level during the last 30 minutes before the set alarm time. The sound slowly increases in 90 seconds to the selected level after the set alarm time.

Note: You can set the light intensity by pressing the light on/off button and then pressing the light intensity + or - button and you can set the alarm volume by pressing the volume increase or decrease button. If you do not want to wake up to the lamp or to a sound, select a light intensity or volume level of 0. See sections 'Using the lamp' and 'Radio/Volume' in this chapter.

1 Push the control lever down to the middle position to switch on the alarm. (Fig. 13) The hour indication of the alarm time flashes (Fig. 14).

To adjust the time, follow steps 2 to 5. If the alarm time is correct, just wait a few seconds.

2 Press the menu + or - buttons to select the hour (Fig. 9).

Note: You can only do this when the hour indication flashes. If this is not the case, push the control lever up and down again to enter the alarm time mode. You can also set the alarm time in the menu. See section 'Menu functions' in this chapter.

3 Press the SELECT button to confirm (Fig. 10). ▶The minute indication of the alarm time starts to flash (Fig. 15).

4 Press the menu + and - buttons to select the minutes. (Fig. 9)

5 Press the SELECT button to confirm or wait for a few seconds (Fig. 10). The appliance leaves the menu and the display shows the clock time.

The alarm time is now set.

Switching off the alarm

To switch off the alarm function, push up the control lever to the top position.

Note: The lamp stays on to light your room. You can switch off the lamp by pressing the light on/off button.

Note: The alarm (sound and/or light) automatically switches off after 90 minutes.

ENGLISH10

Setting the alarm sound (HF3470 only)

See section 'Menu functions' above.

You can choose one of the following sounds:

• Radio (Fig. 16)
• Birds (Fig. 17)
• Beep (Fig. 18)

Snoozing

1 Push down the control lever to the bottom position when the alarm goes off. (Fig. 19)
The lamp continues to be on at the selected intensity level, but the alarm sound stops. After 9 minutes, the wake-up sound is automatically played again.

Note: The 9-minute snooze time is fixed. This time cannot be adjusted.

Note: If you push down the control lever with too much force, it may jump back to off position.

Alarm demonstration

If you want to get a quick demonstration (60 seconds) of the gradually increasing light level and sound level, activate the test function of the appliance.

1 Push the control lever down to the bottom position for a few seconds until TEST appears on the display (Fig. 20).

2 Push the control lever down again to stop the demonstration.

Note: The appliance continues to run the alarm demonstration until you push down the control lever again. The test automatically stops after 9 hours.

Radio/volume (HF3470 only)

1 To switch on the radio, press the radio on/off button. (Fig. 21)
2 To select the desired radio frequency, press the menu + and - button. (Fig. 9)
Tip: To scan radio frequencies automatically, press and hold the menu + or - button for approx. 2 seconds.
Tip: To make sure you get a good radio signal, fully unwind the antenna and move it around until you have found a position at which reception is best.
3 To switch off the radio, press the radio on/off button again.

Volume

1 To set the volume, press the volume increase or decrease button. (Fig. 22) HF3470: You can choose a volume level between 1 and 20. HF3465: You can choose a volume level between 1 and 10.

Note: The volume level you have selected is automatically set as the volume level for the alarm as well.

Setting the display brightness

1 Press the MENU button to enter the menu (Fig. 8).
2 Press the menu + or - button to select the display brightness menu (Fig. 9).
3 Press the SELECT button to enter the display brightness menu (Fig. 10).
4 Press the menu + and - button to change the display brightness (Fig. 9).
5 Press SELECT to confirm (Fig. 10).

Cleaning and maintenance

Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance.

Regularly remove dust from the outside of the appliance with a dry cloth.

1 Unplug the appliance before you clean it.
2 Clean the outside of the appliance with a dry cloth.
Do not let water run into the appliance or spill water onto the appliance (Fig. 3).

Replacement

Except for the lamp, the appliance does not contain any serviceable parts.

The lamp has to be replaced when it stops burning or when the light output decreases (also see chapter 'Important'). You must replace the lamp with a Philips Halogen lamp, 50W, 12V, GY6.35. Only this lamp provides the correct light intensity.

Note: This appliance has been designed to be used with self-shielded lamps only (Fig. 23).

For more information, see chapter 'Guarantee and Service'.

Replacing the lamp

1 Unplug the appliance before you replace the lamp.
2 Let the appliance cool down for approx. 15 minutes.
3 Unlock the top cover of the appliance by pressing it and turning it anticlockwise, until the O symbol on the top cover is aligned with the symbol ● on the lamp housing. (Fig. 24)
4 Remove the top cover. (Fig. 25)
5 Remove the old lamp from the lamp holder (Fig. 26).
6 Insert the pins of the new lamp into the lamp holder. (Fig. 27)

Do not touch the lamp with your fingers. Use a cloth or paper towel when you place the lamp (Fig. 28).

7 Place the top cover back onto the appliance.

8 Lock the top cover by turning it clockwise until the ● symbol on the top cover and the ● symbol on the lamp housing are aligned. (Fig. 29)

Ordering accessories

To purchase accessories for this appliance, please visit our online shop at www.shop.philips.com/service. If the online shop is not available in your country, go to your Philips dealer or a Philips service centre. If you have any difficulties obtaining accessories for you appliance, please contact the Philips Consumer Care Centre in your country. You find its contact details in the worldwide guarantee leaflet.

Environment

- Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment (Fig. 30).

Guarantee and service

If you need service or information or if you have a problem, please visit the Philips website at www.philips.com/support or contact the Philips Consumer Care Centre in your country. You find its phone number in the worldwide guarantee leaflet. If there is no Consumer Care Centre in your country, go to your local Philips dealer.

Troubleshooting

This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, contact the Consumer Care Centre in your country.

Problem Solution

The appliance does not work at all.	Perhaps the plug is not inserted properly in the wall socket. Put the plug properly in the wall socket.
	Perhaps there is a power failure. Check if the power supply works by connecting another appliance.
The appliance functions properly, but the lamp does not work anymore.	Perhaps the lamp has reached the end of its life. The lamp has an expected life of more than 4.000 hours (more than 4 years of normal use). The life depends on the use of the appliance. In case of heavy use, the lamp may not last as long as you expect. If the lamp breaks down, you can order a new one. Contact the Philips Consumer Care Centre in your country.
The appliance becomes hot during use.	This is normal, as the appliance is heated up by the light of the lamp and the electronics. Always let the appliance cool down, before you replace the lamp.
The appliance does not respond when I try to set different functions.	Remove the plug from the wall socket and reinsert it. If you reinsert the plug within approximately 15 minutes, the appliance remembers all settings. If you reinsert the plug after a longer period of time, the appliance will go back to factory settings. You need to set all functions again.
The lamp does not go on when the alarm goes off.	Perhaps you set a light intensity level that is too low. Increase the light intensity level.
	Perhaps you switched off the alarm function by setting the control lever to the top position. To switch on the alarm function, set the control lever to the middle position
	Perhaps the appliance is defective. Contact the Philips Consumer Care Centre in your country.
The lamp does not go on right away when I switch it on.	It takes approx. 1 second for the lamp to go on. This is normal, the lamp needs to heat up.
Problem Solution
I do not hear the alarm sound when the alarm goes off.	Perhaps you set a sound level that is too low. To set a higher sound level, see chapter ‘Using the appliance’, section ‘Radio/volume’.
	Perhaps you switched off the alarm function by setting the control lever to the top position.
	If you selected the radio as the alarm sound, the radio may be defective. Switch on the radio after you switch off the alarm to check if the radio works. If it does not work, contact the Philips Consumer Care Centre in your country.
HF3470: The radio does not work.	The radio may be defective. Contact the Philips Consumer Care Centre in your country.
	Perhaps you set the volume too low. Increase the volume level.
HF3470: The radio produces a crackling sound.	Perhaps the broadcast signal is weak. Adjust the frequency (see chapter ‘Using the appliance’ section ‘Radio/volume’) and/or change the position of the antenna by moving it around. Make sure you have unwound the antenna completely.
The alarm went off yesterday, but it did not go off today.	Perhaps you switched off the alarm function by setting the control lever to the top position.
	Perhaps you set a sound level and/or light intensity level that is too low. Set a higher sound and/or light intensity level.
	Perhaps there was a power failure that lasted more than approximately 15 minutes. In this case the appliance goes back to factory settings. You need to set all functions again.
The alarm did not go off 9 minutes after I pushed the control lever down to snooze.	Perhaps you pushed the control lever down with so much force that it jumped to off position.
	Perhaps you set the volume level to 0.
The light wakes me too early.	Perhaps the light intensity level you have set is not appropriate for you. Try a lower light intensity level if you wake up too early. If light intensity 1 is not low enough, move the appliance further away from the bed.
The light wakes me too late	Perhaps the appliance is positioned at a lower level than your head. Make sure the appliance is located at a height at which the light is not blocked by your bed, duvet or pillow. Also make sure the appliance is not placed too far away.

The lamp flashes. Perhaps the appliance is not suitable for the voltage to which it is connected. Make sure that the voltage indicated on the appliance corresponds to the local mains voltage.

Въведение

• Radio (Sl. 16)
• Ptice (Sl. 17)
• Zvučni signal (Sl. 18)

Odgodeno buđenje

• Radio (Sl. 16)
• Ptice (Sl. 17)
• Zvučni signal (Sl. 18)

Dremanje

1 Pritisnite nadole kontrolnu polugu do donjeg položaja kada se alarm isključi. (Sl. 19)
Lampa će nastaviti da bude uključena na postavljenom nivou intenziteta, ali zvuk alarm će se zaustaviti. Nakon devet minuta zvuk za buđenje će se ponovo automatski reprodukovati.

Napomena: Vreme dremanja od devet minuta je fiksirano. Ovo vreme ne može da se podesi.

Napomena: Ako kontrolnu ručicu pritisnete nadole suviše jako, može da se vrati u položaj za isključivanje.

Diagram showing three open panels with grid patterns and curved arrows indicating rotation or movement (no text or symbols)