7009078 - Flat Screen Mount Acme United - Free user manual and instructions

Product Type	Flat Screen Wall Mount
Compatible Screen Sizes	26" - 55"
Max Weight Capacity	80 lbs (36 kg)
VESA Compatibility	200x200mm to 400x400mm
Tilt Range	+/- 15 degrees
Swivel Range	+/- 30 degrees
Level Adjustment	+/- 3 degrees
Material	Steel
Color	Black
Product Dimensions (WxHxD)	50 x 25 x 5 cm
Product Weight	3.5 kg
Installation Type	Wall mount (studs required)
Included Hardware	Mounting bracket, screws, anchors, spacers
Safety Features	Weight-tested, anti-tip design
Maintenance	Wipe with a damp cloth; no solvents
Repairability	Not user-serviceable; contact Acme United support
Warranty	1 year limited warranty

Frequently Asked Questions - 7009078 Acme United

What is the maximum TV weight this mount can support?

The mount supports up to 80 lbs (36 kg).

What VESA patterns are compatible?

It fits VESA patterns from 200x200mm to 400x400mm.

Does the mount tilt or swivel?

Yes, it offers +/-15° tilt and +/-30° swivel for optimal viewing angles.

What tools are needed for installation?

You need a drill, level, socket wrench, and stud finder. All hardware is included.

Can I install this on drywall?

Yes, but you must mount into wood studs for safety. Use included anchors for concrete walls.

How do I clean the mount?

Wipe with a damp cloth. Do not use abrasive cleaners or solvents.

Is the mount compatible with curved TVs?

Yes, as long as the VESA pattern is within 200x200 to 400x400 and weight under 80 lbs.

What is the depth from the wall?

The mount profile is approximately 2 inches (5 cm) from the wall.

Can I adjust the level after installation?

Yes, there is a +/-3° level adjustment feature.

Where can I find the user manual?

Download the manual for free at notice-facile.com in PDF format.

USER MANUAL 7009078 Acme United

Technical line drawing of a mechanical support frame with vertical supports and horizontal plates (no text or symbols)

Universal

Wall Bracket

Solid orange horizontal bar with no text or symbols

GB 4 Installation Instruction 88 Warranty card

LT 11 Montavimo instrukcija 89 Garantinis lapas

Unpacking instructions

• Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
• Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts.
• Carefully read all instructions before attempting installation.

Important safety information

Install and operate this device with care. Please read this instruction before beginning the installation, and carefully follow all instructions contained herein. Use proper safety equipment during installation.

Please call a qualified installation contractor for help if you:

• If you don't understand these directions or have any doubts about the safety of the installation.
• If you are uncertain about the nature of your wall, consult a qualified installation contractor.

Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaim any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

	This TV mount must be securely attached to the vertical wall. If the mount is not properly installed it may fall, resulting in possible injury and/or damage.
Tools Required	5/32"(4mm) Drill BitScrewdriver	3/8"(10mm) Masonry BitStud Finder	Wrench or Socket SetCarpenter's Level

Note: The mounting components and hardware supplied in this package are not designed for installations to walls with steel studs or to cinder block walls. If the hardware you need for your installation is not included, please consult your local hardware store for proper mounting hardware for the application.

GB

Supplied parts list

(1)Wall Plate-a (1)Left Monitor Bracket-b (1)Right Monitor Bracket-c
(4)M4x12 Bolt-d	(4)M5x12 Bolt-e	(4)M6x12 Bolt-f	(4)M8x16 Bolt-g
(4)M4x30 Bolt-h	(4)M5x30 Bolt-i	(4)M6x35 Bolt-j	(4)M8x40 Bolt-k
(4)M4/M5 Space-l	(4)M6/M8 Space-m	(8)M4/M5 Washer-n	(4)M6/M8 Washer-o
(3)Lag Bolt-p	(3)Lag Bolt Washer-q	(3)Concrete Anchor-r

Mounting the monitor brackets to a TV with flat back

First of all, make sure the diameter of the Bolt (d, e, f, g) your TV requires. Once you have determined the correct diameter, please see the relative diagram as below. You will thread the Bolt into the TV using the correct Washer (n, o). Please make sure the Monitor Brackets (b, c) are vertically centered and level with each other.

GB

Mounting the monitor brackets to a TV with curved back

First of all, make sure the diameter of the Bolt(h,i,j,k) your TV requires. Once you have determined the correct diameter, please see the relative diagram as below. You will thread the Bolt into the TV using the correct Washer(n,o) and spacer(l,m). For the M4 or M5 diameter bolt, you will need another M4/M5 Washer between the Monitor Bracket and the Spacer. Please make sure the Monitor Brackets are vertically centered and level with each other.

Mounting the wall plate to the wall

Brick, Solid Concrete and Concrete Block mounting:

Use the Wall Plate(a) as a template to mark 3 hole locations on the wall. Make sure these holes are level. Pre-Drill these holes with a 3/8"(10mm) masonry bit to at least 2.4"(60mm) in depth. Insert a Concrete Anchor(r) into each of these holes. Make sure the anchor is seated completely flush with the concrete surface even if there is a layer of drywall or other material in front. Attach the Wall Plate to the wall using 3pcs Lag Bolts(p) and 3pcs Lag Bolt Washers(q), shown in Diagram 2A.

Wood Stud mounting:

The Wall Plate(a) must be mounted to two wood studs at least 16"(406mm) apart. Use a stud finder to locate two adjacent studs. It is a good idea to verify where the studs are located with an awl or thin nail shown in Diagram 2B. Pre-drill a 2.4"(60mm) deep hole at the desired height in each stud using a 5/32"(4mm) drill bit. Make sure these holes are in the center area of the studs and level with each other. Attach the Wall Plate to the wall using the 2pcs Lag Bolts(p) and 2pcs Lag Bolt Washers(q).

Attaching monitor to wall plate

Warning: Some TVs may require two people to lift! We are not responsible for personal injury or product damage.

First pull the rope on the each end of Bracket(b,c) to release the spring locking system, as shown in Diagram 3A, then hook the Bracket on the Wall Plate(a), last loose the rope to lock the Brackets on the position, as shown in Diagram 3B.

Technical line drawing of a mechanical component with two vertical supports and a central horizontal bar (no text or symbols)

Thanks for choosing our products, enjoy the using.

Technical line drawing of a rectangular device with two vertical supports and a central horizontal bar (no text or symbols)

Technical line drawing of a rectangular device with vertical supports and a central control panel (no text or symbols)

Technical line drawing of a rectangular device with vertical supports and a central horizontal bar (no text or symbols)

Technical line drawing of a rectangular device with vertical supports and a central horizontal bar (no text or symbols)

Technical line drawing of a rectangular device with vertical supports and a central screen (no text or symbols)

Technical line drawing of a rectangular device with two vertical supports and a central horizontal bar (no text or symbols)

Technical line drawing of a rectangular device with vertical supports and a central control panel (no text or symbols)

Technical line drawing of a rectangular device with two vertical supports and a central horizontal bar (no text or symbols)

Technical line drawing of a mechanical component with two vertical supports and a central horizontal bar (no text or symbols)

Technical line drawing of a rectangular device with two vertical supports and a central screen (no text or symbols)

Technical line drawing of a rectangular device with vertical supports and a central control panel (no text or symbols)

Product Product model
Product purchase date Seller name, address
Failures (date, description, position of the person who accepts the product, first name, last name and signature)

1. Warranty period

Warranty enters into force starting with the day when the buyer acquires the product from the seller. Warranty period is indicated on the package of the product.

2. Warranty conditions

The warranty is valid only by providing an original document of the product acquisition and this warranty sheet, which includes name of the product model, product purchase date, name and address of the seller.

If it is noticed during the warranty period that the product has faults and these faults where not caused by any of the reasons when the warranty is not applied as indicated in the paragraphs below, manufacturer undertakes to replace the product.

The warranty is not applied to regular testing, maintenance and repair or replacement of the parts which are worn out naturally.

The warranty is not applied if damage or failures occurred due to the following reasons:

• Inappropriate installation of the product, inappropriate usage and/or open product without following the manual, technical requirements and safety standards as provided by the manufacturer, and additionally, inappropriate warehousing, falling from heights as well as hard strikes.
  • Corrosion, mud, water and sand.
• Repair works, modifications or cleaning, which were performed by a authorised by the manufacturer.
• Usage of the spare parts, software or consumptive materials which do not apply to the product.
• Accidents or events or any other reasons which do not depend on the manufacturer, which includes lightning, water, fire, magnetic field and inappropriate ventilation.
• If the product does not meet standards and specifications of a particular which it was not bought. Any attempt to adjust the product in order to meet technical and safety requirements such as those in the other countries withdraws all the rights to the warranty service.

If no failures are detected in the product, all the expenses in relation to the service are covered by the buyer.

Garantinis lapas www.acme.eu/warranty