Q: How to remove and clean the metal filter of the FALMEC MANHATTAN?

Removing the filter: Open the hood panel and operate handle A to release the grease filter. Carefully remove it. Cleaning the filter: The metal filter should be washed every month in hot water with a little mild detergent. Avoid bending the filter during cleaning. Allow it to dry completely before reinstalling it on the hood. Regular cleaning is important to prevent grease buildup and fire risk. Maintenance alert: After approximately 30 hours of operation, the red light on the timer button will stay on to indicate that the metal filter needs cleaning. To deactivate this alert, press the timer button for a few seconds until the red light goes off. Then turn the hood off and on again to check that the alert has disappeared. Charcoal filters: Once the metal filter is removed, you can access the two charcoal filters located at the ends of the motor. These filters cannot be cleaned and should be replaced approximately every 3 to 4 months depending on your usage.

Question 1

How do you install the FUTURA hood?

Accepted Answer

The installation of the FUTURA hood consists of four main phases:

Phase 1 - Wall support bracket

Install a support bar at a height calculated as X + Y + 310 mm above the cooking surface. Check the horizontal alignment with a level and drill two holes for the expansion anchors.

Phase 2 - Attaching the hood

Hang the hood on the support bar and adjust the alignment using the screws provided on the brackets. The upper screw adjusts the distance from the wall, while the lower screw controls the vertical positioning.

Phase 3 - Wall fastening

Secure to the wall using an expandable plug and the corresponding screws, through the designated holes on the back of the hood or the individual protection tabs, to prevent movement. For models with external evacuation, connect the fan outlet to an external evacuation using appropriate ducting.

Phase 4 - Telescopic extension

Insert the extension into the channel, secure it with 8 screws, and adjust its height as desired. Mark the wall positions, install the anchors, and secure the extension bracket with the screws provided.

Minimum safety distance from the cooking surface: 65 cm for gas appliances. Installation must be carried out by a qualified installer according to applicable standards.

Question 2

How to open the FALMEC MANHATTAN hood to access the filters?

Accepted Answer

To open the FALMEC MANHATTAN hood and access the filters, follow these steps:

Open the front panel - Lift or pull the front panel of the extractor hood.
Operate handle A - Once the panel is open, locate the handle marked "A" and operate it to release the metal filter. This mechanism safely releases the filter.
Remove the metal filter - Gently pull the filter towards you after operating the handle.
Access the charcoal filters - Once the metal filter is removed, you can access the two charcoal filters located at the ends of the motor. Unlike the metal filter, these filters cannot be cleaned but must be replaced only.

Note: The metal filter is removable and washable. You can clean it with hot water and a mild detergent before reinstalling it. Allow it to dry thoroughly before use.

Question 3

How to remove and clean the metal filter of the FALMEC MANHATTAN?

Accepted Answer

Removing the filter: Open the hood panel and operate handle A to release the grease filter. Carefully remove it.

Cleaning the filter: The metal filter should be washed every month in hot water with a little mild detergent. Avoid bending the filter during cleaning. Allow it to dry completely before reinstalling it on the hood. Regular cleaning is important to prevent grease buildup and fire risk.

Maintenance alert: After approximately 30 hours of operation, the red light on the timer button will stay on to indicate that the metal filter needs cleaning. To deactivate this alert, press the timer button for a few seconds until the red light goes off. Then turn the hood off and on again to check that the alert has disappeared.

Charcoal filters: Once the metal filter is removed, you can access the two charcoal filters located at the ends of the motor. These filters cannot be cleaned and should be replaced approximately every 3 to 4 months depending on your usage.

Question 4

What does the red light on the FALMEC MANHATTAN hood mean?

Accepted Answer

The red light indicates that the grease filter metal screens are saturated after approximately 30 hours of operation. It is a maintenance alert reminding you that your filters need to be cleaned.

To turn off the red light, press the timer and clogged filter alarm button (the same button that manages the automatic timer) and hold it down for a few seconds until the red light goes out. Then completely turn off the hood, and restart it to confirm that the alert has disappeared.

Cleaning the metal filters: Once the light is off, proceed to clean your grease filter metal screens. Wash them every month with hot water and a mild detergent, without bending them. Wait until they are completely dry before putting them back in place. You can wash them by hand or in the dishwasher.

Replacing the charcoal filters: The activated charcoal filters cannot be cleaned. They should be replaced every 3 to 4 months on average depending on your usage. To order replacement filters, contact your dealer or refer to the order coupon provided with your hood.

By adhering to this regularity of cleaning and replacing the filters, the red light will only reappear after approximately 30 hours of operation.

Question 5

How to replace the neon lights of the FALMEC DIAMANTE kitchen hood?

Accepted Answer

To replace the neon lights of your FALMEC DIAMANTE kitchen hood, follow these simple and safe steps:

Steps to replace the neon lights:

Unplug the hood: Before any intervention, ensure that the hood is disconnected from the power supply to avoid any risk of electric shock.
Access the neon lights: Depending on the model, it may be necessary to remove a cover or panel located under the hood. Use a screwdriver to unscrew the fasteners or gently unclip the cover to access the neon tubes.
Remove the old neon lights: Gently grasp the neon tube and turn it slightly counterclockwise to release it from its supports. Handle with care to avoid breaking the tube.
Install the new neon lights: Insert the new tube into the supports, then turn it clockwise until it is securely fixed and stable.
Replace the cover: Put the cover or panel back and screw it or clip it securely.
Reconnect the hood: Plug the hood back into the power supply.
Test the lighting: Turn on the hood to check that the new neon lights are working properly.

Additional tips:

Only use neon tubes compatible with the FALMEC DIAMANTE model.
If the neon lights do not turn on after replacement, check the connections or the presence of a fuse to replace.
In case of doubt, consult a professional to ensure a safe installation.

Question 6

What are the compatible filter references for the FALMEC MIRABILIA hood?

Accepted Answer

The FALMEC MIRABILIA kitchen hood generally uses two types of filters: grease filters and activated carbon filters, depending on your hood's configuration (extraction or recirculation).

Grease Filters

These filters are often made of aluminum or stainless steel and are designed to trap grease and particles during cooking.
For the MIRABILIA model, the grease filters are generally compatible with the specific dimensions of the hood, so it is important to check the exact size before purchase.

Activated Carbon Filters

Primarily used in hoods operating in recirculation mode, these filters neutralize cooking odors.
The references for carbon filters may vary depending on the version of the MIRABILIA hood, so it is recommended to choose a filter suitable for this model.

Tips for Buying Filters

Identify the type of filter you need (grease or carbon).
Measure or check the dimensions of the current filters to ensure compatibility.
Contact an authorized FALMEC dealer or consult specialized websites to obtain the exact references for filters for the MIRABILIA.

By following these guidelines, you will easily find and replace the filters suitable for your FALMEC MIRABILIA hood to ensure optimal operation and good air quality in your kitchen.

Question 7

Why does my FALMEC West hood start at too high a speed?

Accepted Answer

The main cause of your FALMEC West hood starting at too high a speed is the desired speed function. This function allows the hood to automatically restart at the last speed selected before the previous shutdown. If you had used speed 2 or 3 (or the 4th intensive speed if your model has it), the hood will restart at that same speed each time it is turned back on.

To solve this issue, always set your hood to speed 1 (minimum) before turning it off, then turn it off. The next time you turn it on, it will start directly at speed 1. You can then gradually increase the speed if necessary using the + and - buttons on your control panel.

If your hood restarts at speed 4 (intensive mode), check that the + button is not accidentally stuck. The intensive mode is limited to 15 minutes before automatically returning to speed 3. Also, check that this mode was not inadvertently activated before the previous shutdown.

To use your FALMEC West optimally, adopt these habits: use speed 1 to keep the air clean with minimal energy consumption, speed 2 under normal cooking conditions, and speed 3 only in the presence of strong odors or a lot of steam. Remember to turn off your hood by always bringing it back to speed 1 to avoid these unwanted restarts.

If the problem persists despite these adjustments, it is possible that a button is stuck or there is a malfunction in the control panel. In this case, consult an authorized Service Center for a technical diagnosis.

Question 8

How to level a FALMEC PRISMA hood fixed by 4 cables?

Accepted Answer

To level your FALMEC PRISMA hood equipped with a 4-cable fixation, start by ensuring that it is properly suspended and that the 4 cables are securely attached to the upper mounting structure. The hood, weighing 15 kg, must be stable and all mounting elements must be secured before making adjustments. This operation should be performed by qualified personnel as recommended by the manufacturer.

Place a level on top of the hood to check its horizontal position and identify the sides that need adjustment. Locate the cables that need to be shortened or lengthened to correct the tilt. Note: you must adjust the 4 cables evenly to maintain the overall stability of the hood and avoid permanent tilting.

To adjust each cable, proceed as follows:

Loosen the fixation of the concerned cable slightly to modify its length
Pull or release the cable to change the height of the hood on that specific side
Once the adjustment is made, immediately tighten the cable fixation
Repeat this operation for each cable that needs it, proceeding gradually

After each adjustment, place your level back on the hood to check that you are progressing towards a perfectly horizontal position. Balance the adjustments between the four cables to maintain an evenly distributed load and avoid imbalances.

Once the hood is perfectly leveled and horizontal, ensure that all cable fixations are tightly secured. Check that the mandatory safety screws, specified by the manufacturer, are in place and properly tightened. This final securing guarantees the stability, safety, and proper functioning of the installation in the long term. Your PRISMA is now ready to effectively extract cooking fumes and vapors.

User manual FALMEC : user manuals and guides in PDF

Models FALMEC most viewed

Browse manuals FALMEC by appliance type

Recent questions about devices FALMEC