Question 1

How to use the ULTIMATE SPEED KH 4106 MINI COMPRESSOR?

Accepted Answer

The ULTIMATE SPEED KH 4106 MINI COMPRESSOR is designed to be easy to use. Here are the steps to follow for proper use:

1. Preparation

Place the compressor on a flat and stable surface. Ensure that the device is clean and in good condition before use.

2. Electrical connection

Plug the compressor into a suitable power source. Make sure the cable is properly connected and the socket is secure.

3. Pressure adjustment

If the compressor has a pressure setting, select the desired pressure based on the use (for example, inflating tires, air mattresses, etc.).

4. Connection to the object to inflate

Attach the hose or nozzle of the compressor to the object to be inflated. Ensure that the connection is airtight to avoid any air leaks.

5. Starting

Turn on the compressor by pressing the power button. The device will start injecting air into the connected object.

6. Pressure monitoring

Monitor the built-in pressure gauge (if present) to check the pressure and stop the compressor once the desired pressure is reached.

7. Stopping and disconnecting

Turn off the compressor, then unplug the hose or nozzle from the inflated object.

8. Storage

Allow the compressor to cool down before storing it in a dry and safe place.

By following these steps, you will use your ULTIMATE SPEED KH 4106 MINI COMPRESSOR safely and effectively.

Question 2

What is the time required for a full charge with the ULTIMATE SPEED ULG 3.8 A1 battery charger?

Accepted Answer

The full charging time with the ULTIMATE SPEED ULG 3.8 A1 battery charger mainly depends on the battery capacity (in Ah) and the selected charging mode. This charger offers four distinct modes, each optimized for different types and capacities of batteries.

Charging time calculation: Generally, the charging time is calculated by dividing the battery capacity (in Ah) by the charging current (in A). For example, with Mode 3 (3.6A), a 12V battery of 50 Ah will charge in about 14 hours (50 ÷ 3.6 ≈ 14 hours). With Mode 4 (3.8A), the same calculation gives about 13 hours (50 ÷ 3.8 ≈ 13 hours).

Mode 1 (6V - 0.8A): For 6V batteries with a capacity of less than 14 Ah. A 6V battery of 10 Ah will fully charge in about 12 to 13 hours. This mode is suitable for small batteries of vintage vehicles or light motorcycles.

Mode 2 (12V - 0.8A): For 12V batteries with a capacity of less than 14 Ah. A 12V battery of 10 Ah will fully charge in about 12 to 13 hours. This mode is ideal for small batteries, especially for backup or light starting batteries.

Mode 3 (12V - 3.6A): For 12V batteries with a capacity between 14 and 120 Ah under normal conditions. A 12V battery of 50 Ah will charge in about 14 hours, a 70 Ah battery in about 20 hours, and a 100 Ah battery in about 28 hours. This is the most commonly used mode for modern cars.

Mode 4 (12V - 3.8A): For 12V batteries with a capacity greater than 14 Ah in cold conditions or for AGM batteries (Absorbent Glass Mat technology). With its slightly higher current (3.8A), this mode allows for a somewhat faster charge: a 12V battery of 50 Ah will charge in about 13 hours, a 70 Ah battery in about 18 to 19 hours.

Other factors influencing duration: The initial state of the battery, ambient temperature, and discharge level also affect the charging time. A completely discharged battery will take longer than a partially discharged battery. For heavily discharged batteries (below 10.5V), the charger first activates a pulse charging mode to gradually regenerate them, which extends the total duration.

Question 3

How do I check the compatibility of my battery with the ULTIMATE SPEED ULG 3.8 A1 charger?

Accepted Answer

Your battery is compatible with the ULTIMATE SPEED ULG 3.8 A1 charger if it meets the following specifications. First, check the type of battery: this charger only accepts rechargeable lead-acid batteries with liquid electrolyte (lead-acid) or gel. It must never be used with lithium-ion batteries or non-rechargeable cells.

Next, check the nominal voltage of your battery. The ULG 3.8 A1 charger works with batteries of 6V or 12V only. You will find this information engraved on the battery case.

The capacity in ampere-hours (Ah) is the determining criterion. This charger accepts:

For 6V batteries: capacity from 1.2 Ah to 14 Ah
For 12V batteries: capacity from 1.2 Ah to 14 Ah or from 14 Ah to 120 Ah

Check the capacity indicated on your battery. If it falls within one of these ranges, your battery is compatible.

Also, ensure that the connectors of your battery match the clamps of the charger. If the connectors do not match, you will not be able to charge the battery safely.

The ULG 3.8 A1 charger includes several protections: against short circuits, reverse polarity, and overheating. Thanks to its three-phase charging technology, it can even regenerate completely discharged batteries. Before plugging in the charger, always check that the battery is not damaged and that all connectors are dry and clean.

In summary, to confirm compatibility, check: the type (lead-acid or gel), the voltage (6V or 12V), the capacity (see ranges above), and the compatibility of the connectors. Once these points are verified, you can charge your battery with confidence.

Question 4

How to use the ULTIMATE SPEED ULG 3.8 A1 battery charger?

Accepted Answer

To properly use the ULTIMATE SPEED ULG 3.8 A1 battery charger, follow these steps:

1. Preparation

Ensure that the charger is unplugged before handling.
Check that the battery to be charged is compatible with this charger.

2. Connecting to the battery

Connect the red cable (positive) to the positive (+) terminal of the battery.
Connect the black cable (negative) to the negative (-) terminal of the battery.

3. Powering on

Plug the charger into a suitable electrical outlet.
If the charger has a switch, set it to the

User manual ULTIMATE SPEED : user manuals and guides in PDF

Models ULTIMATE SPEED most viewed

Browse manuals ULTIMATE SPEED by appliance type

Recent questions about devices ULTIMATE SPEED