Question 1

How to recharge a completely discharged 12-volt battery?

Accepted Answer

To recharge a completely discharged 12-volt battery with the ULTIMATE SPEED ULGD 3.8 A1 charger, follow these steps:

1. Preparation:

Clean the battery terminals
Ensure good ventilation (ambient temperature between 0°C and 40°C)
Turn off the vehicle's ignition

2. Connection:

Connect the positive (red) clamp to the positive terminal of the battery
Connect the negative (black) clamp to the negative terminal or to the chassis (at least 10 cm from the battery)
Plug the power cable into the electrical outlet (220-240V)
The LCD screen displays the battery voltage

3. Program selection:

For a completely discharged 12V battery, choose:

Mode 3 (14.4V - 3.8A): for 12V batteries from 14 to 120 Ah
Mode 4 (14.7V - 3.8A): for 12V AGM batteries or in cold conditions

This charger features automatic regeneration that allows recovering deeply discharged batteries. The LEDs indicate the charging status and reverse polarity detection protects the device.

4. Disconnection:

Unplug from the electrical network
Remove the negative (black) clamp
Remove the positive (red) clamp

The battery can support a capacity of 1.2 Ah to 120 Ah for 12V. The charger automatically switches to maintenance mode once the full charge is reached.

Question 2

What is the time required for a full charge with the ULTIMATE SPEED ULG 3.8 A1 battery charger?

Accepted Answer

The full charging time with the ULTIMATE SPEED ULG 3.8 A1 battery charger mainly depends on the battery capacity (in Ah) and the selected charging mode. This charger offers four distinct modes, each optimized for different types and capacities of batteries.

Charging time calculation: Generally, the charging time is calculated by dividing the battery capacity (in Ah) by the charging current (in A). For example, with Mode 3 (3.6A), a 12V battery of 50 Ah will charge in about 14 hours (50 ÷ 3.6 ≈ 14 hours). With Mode 4 (3.8A), the same calculation gives about 13 hours (50 ÷ 3.8 ≈ 13 hours).

Mode 1 (6V - 0.8A): For 6V batteries with a capacity of less than 14 Ah. A 6V battery of 10 Ah will fully charge in about 12 to 13 hours. This mode is suitable for small batteries of vintage vehicles or light motorcycles.

Mode 2 (12V - 0.8A): For 12V batteries with a capacity of less than 14 Ah. A 12V battery of 10 Ah will fully charge in about 12 to 13 hours. This mode is ideal for small batteries, especially for backup or light starting batteries.

Mode 3 (12V - 3.6A): For 12V batteries with a capacity between 14 and 120 Ah under normal conditions. A 12V battery of 50 Ah will charge in about 14 hours, a 70 Ah battery in about 20 hours, and a 100 Ah battery in about 28 hours. This is the most commonly used mode for modern cars.

Mode 4 (12V - 3.8A): For 12V batteries with a capacity greater than 14 Ah in cold conditions or for AGM batteries (Absorbent Glass Mat technology). With its slightly higher current (3.8A), this mode allows for a somewhat faster charge: a 12V battery of 50 Ah will charge in about 13 hours, a 70 Ah battery in about 18 to 19 hours.

Other factors influencing duration: The initial state of the battery, ambient temperature, and discharge level also affect the charging time. A completely discharged battery will take longer than a partially discharged battery. For heavily discharged batteries (below 10.5V), the charger first activates a pulse charging mode to gradually regenerate them, which extends the total duration.

Question 3

How do I check the compatibility of my battery with the ULTIMATE SPEED ULG 3.8 A1 charger?

Accepted Answer

Your battery is compatible with the ULTIMATE SPEED ULG 3.8 A1 charger if it meets the following specifications. First, check the type of battery: this charger only accepts rechargeable lead-acid batteries with liquid electrolyte (lead-acid) or gel. It must never be used with lithium-ion batteries or non-rechargeable cells.

Next, check the nominal voltage of your battery. The ULG 3.8 A1 charger works with batteries of 6V or 12V only. You will find this information engraved on the battery case.

The capacity in ampere-hours (Ah) is the determining criterion. This charger accepts:

For 6V batteries: capacity from 1.2 Ah to 14 Ah
For 12V batteries: capacity from 1.2 Ah to 14 Ah or from 14 Ah to 120 Ah

Check the capacity indicated on your battery. If it falls within one of these ranges, your battery is compatible.

Also, ensure that the connectors of your battery match the clamps of the charger. If the connectors do not match, you will not be able to charge the battery safely.

The ULG 3.8 A1 charger includes several protections: against short circuits, reverse polarity, and overheating. Thanks to its three-phase charging technology, it can even regenerate completely discharged batteries. Before plugging in the charger, always check that the battery is not damaged and that all connectors are dry and clean.

In summary, to confirm compatibility, check: the type (lead-acid or gel), the voltage (6V or 12V), the capacity (see ranges above), and the compatibility of the connectors. Once these points are verified, you can charge your battery with confidence.

Question 4

How to use the ULTIMATE SPEED ULG 3.8 A1 battery charger?

Accepted Answer

To properly use the ULTIMATE SPEED ULG 3.8 A1 battery charger, follow these steps:

1. Preparation

Ensure that the charger is unplugged before handling.
Check that the battery to be charged is compatible with this charger.

2. Connecting to the battery

Connect the red cable (positive) to the positive (+) terminal of the battery.
Connect the black cable (negative) to the negative (-) terminal of the battery.

3. Powering on

Plug the charger into a suitable electrical outlet.
If the charger has a switch, set it to the

User manual ULTIMATE SPEED Battery charger : user manuals and guides in PDF

Models ULTIMATE SPEED Battery charger most viewed

Other categories ULTIMATE SPEED

Recent questions about Battery charger ULTIMATE SPEED