Z30544 - Hydraulic jack ULTIMATE SPEED - Free user manual and instructions

Product Type	Measuring Device
Brand	Ultimate Speed
Model	Z30544
Dimensions (approx.)	150 x 80 x 35 mm
Weight (approx.)	250 g
Power Supply	2 x 1.5 V AAA batteries
Display	LCD, 3.5 digits
Measuring Functions	AC/DC voltage, resistance, continuity, diode test
Voltage Range (AC)	200 mV to 600 V
Voltage Range (DC)	200 mV to 600 V
Resistance Range	200 Ω to 20 MΩ
Safety Rating	CAT II 600 V
Overload Protection	Yes, on resistance range
Low Battery Indication	Yes
Auto Power Off	Yes, after approx. 15 min
Operating Temperature	0 °C to 40 °C
Storage Temperature	-10 °C to 50 °C
Humidity	< 80 % RH non-condensing
Accessories Included	Test leads, manual, batteries
Cleaning Instructions	Wipe with a dry cloth; do not use solvents
Spare Parts Availability	Test leads can be ordered separately
Repair Service	Contact authorized service center
Warranty	2 years from purchase date

Frequently Asked Questions - Z30544 ULTIMATE SPEED

How do I turn on the Ultimate Speed Z30544?

Turn the rotary switch from the OFF position to any measurement function. The device will power on automatically.

What does the OL reading mean?

OL stands for Over Limit. It indicates that the measured value exceeds the current range. Select a higher range if possible.

How do I measure DC voltage?

Set the rotary switch to the V⎓ position. Connect the red test lead to the V/Ω terminal and the black lead to the COM terminal. Touch the probes to the circuit in parallel. Read the value on the display.

How do I test continuity?

Set the rotary switch to the continuity symbol (usually a diode or sound wave). Connect the test leads to the circuit. If the resistance is less than about 50 Ω, the buzzer will sound.

Why does the display show a battery symbol?

The battery symbol indicates low battery. Replace the two AAA batteries with fresh ones to ensure accurate measurements.

Can I measure current with this device?

The Z30544 model does not include current measurement. It measures voltage, resistance, continuity, and diodes only.

What safety precautions should I take?

Always start with the highest range if the value is unknown. Do not measure voltages above 600 V. Use the device only in dry environments. Remove test leads before opening the battery compartment.

How do I clean the device?

Wipe the housing with a soft, dry cloth. Do not use any liquids, detergents, or abrasives, as they may damage the device.

What does the HOLD button do?

Press the HOLD button to freeze the current reading on the display. Press again to release the hold and return to live measurements.

Where can I find spare test leads?

Spare test leads can be ordered from the manufacturer's website or through authorized dealers. Use only leads with the same safety rating (CAT II 600 V).

USER MANUAL Z30544 ULTIMATE SPEED

Line drawing of a hand pump with directional arrows indicating motion (no text or symbols)

ULTIMATE SPEED

Table of contents

Introduction

Proper use....Page 5

Description of parts....Page 5

Technical data......Page 5

Included items Page 5

Safety notes......Page 5

Use

Raising the vehicle....Page 6

Lowering the vehicle....Page 6

Cleaning and Care......Page 7

Maintenance and storage

Topping up the hydraulic oil/greasing......Page 7

Removing air from the hydraulic system....Page 7

Storing......Page 7

Troubleshooting Page 8

Disposal Page 8

Informations

Declaration of Conformity....Page 8

4 GB/IE

ULTIMATE SPEED

Hydraulic Bottle Jack

- Introduction

These operating instructions form a part of this product. Make yourself familiar with all the operating instructions and safety advice for the product before use. Use the product only as described and for the indicated purpose. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.

- Proper use

The hydraulic vehicle jack is intended for raising and lowering motor vehicles. Other uses or modification of the hydraulic vehicle jack shall be considered as improper use and may lead to injury or damage. The manufacturer will not accept liability for loss or damage arising from improper use. The product is not intended for commercial use.

Note: Reclose the release valve 5 after each use!

● Description of parts

1 Support plate
2 Extension screw
3 Lifting handle socket
4 Safety valve
5 Release valve
6 Lifting handle (for pump mechanism)
7 Rod (for release valve)
8 Oil plug

- Technical data

Stroke: Approx. 21 - 42.5 cm

Maximum load: 6000 kg

Weight: Approx. 4.5 kg

Hydraulic oil: Complies with ISO VG15

- Included items

1 Hydraulic vehicle jack
1 Lifting handle
1 Rod for release valve
1 Operating instructions

Safety notes

⚠️ DANGER! Follow the instructions below to avoid the threat of loss of life, injury, or damage to the product etc.

■ Always use axle stands and wheel chocks in addition to your hydraulic vehicle jack. Never work under a raised vehicle unless you have taken additional safety precautions. This is intended to prevent the vehicle from rolling away, sliding off or overturning the jack.
Use the product on a solid, level surface only. Using the product on an unstable or uneven surface – such as a gravel surface – may lead to the load slipping.
■ Ensure that you never exceed the allowable (rated) load capacity.

The person operating the jack must observe the jack and the load during all movements.
■ Never work under the raised load if it has not been made secure by suitable means.
Do not allow the hydraulic vehicle jack to be used by uninstructed or inexperienced persons.
Before using the hydraulic vehicle jack take precautions to prevent the vehicle from rolling away. Put the handbrake on, place the vehicle in gear (with automatic gearboxes set to "P") and chock the wheels.
Even with safety measures in place always remain alert and make a visual check that the support plate 1 is firmly seated against the vehicle jacking point.
■ Make sure that no petrol, battery acid or any other dangerous substance can flow out of the vehicle when the vehicle is being lifted.
- Check that no person or object is under the vehicle before you lower it.
■ Lower the vehicle slowly.

5 GB/IE

Safety notes / Use

• Check that all parts have been assembled and fitted properly and are undamaged.
  Before each use check that the hydraulic vehicle jack is working properly. Check the screws and valves of the hydraulic vehicle jack for correct seating and look out for hydraulic oil leaks in particular.
• Never use the hydraulic vehicle jack for moving or loading a vehicle. Never use it to lift a whole vehicle completely off the ground.
  Make sure that no-one - especially a child - is in the vehicle and that everyone is kept at an adequate distance away from the vehicle when the hydraulic vehicle jack is in use.
  ■ Never change the setting of the safety valve 4. It is preset to the correct setting in the factory and must never be readjusted later.
• Do not use the hydraulic car jack if the sealing (safety valve 4) is damaged.
  If the vehicle jack is damaged, have it repaired by a suitably qualified person only.
  ■ Under no circumstances carry out any modifications to the vehicle jack.
  CAUTION! RISK OF SHEARING AND CRUSHING INJURY! Keep your fingers away from the area of

the lifting handle socket 3 while pumping. Failure to observe this advice may result in shearing and crushing injury.

Use

● Raising the vehicle

⚠️ CAUTION! RISK TO LIFE! Check that the vehicle jack and axle stands are in an undamaged condition before you use them. Ensure that the hydraulic vehicle jack is used only in combination with axle stands. Have your axle stands to hand before raising the vehicle. If you do not use axle stands, the vehicle may tip over and cause a risk to life.

Follow these steps:

☐ Ensure that the rod 7 is fully lowered and the extension screw 2 is completely screwed in before you put away the vehicle jack.

Place the hydraulic vehicle jack in the desired position. In choosing the position, observe the provisions of the owner's manual for your vehicle.
☐ If necessary screw out the extending screw 2 until it comes into contact with the underside of the vehicle (Fig. B).
☐ Connect the rod 7 to the lifting handle 6 to extend the lifting handle.
CAUTION! RISK OF SHEARING AND CRUSHING INJURY! Keep your fingers away from the area of

the lifting handle socket 3 while pumping. Failure to observe this advice may result in shearing and crushing injury.

☐ Guide the end of the lifting handle 6 into the lifting handle socket 3 and pump the vehicle up to the desired height (Fig. C).
☐ Place the axle stands under the designated jacking points under the vehicle.
☐ Relieve the load from the vehicle jack by placing the rod 7 with the oval opening on to the release valve 5, then turning the rod 7 slightly anticlockwise before turning it back immediately. The support plate 1 drops slightly and the vehicle is held on the axle stands.

● Lowering the vehicle

DANGER TO LIFE! Check that no person or object is under the vehicle before you lower it.
CAUTION! Lower the vehicle slowly, otherwise there is the danger of injury and damage to the product or to the vehicle.

☐ First raise the vehicle slightly in order to be able to remove the axle stands. Proceed as described in the section on „Raising the vehicle“.
□ Remove the axle stands.
Place the rod 7 with oval opening on to the release valve 5 and turn the rod slowly anticlockwise (Fig. A). The vehicle is lowered slowly.

Note: The more quickly the rod 7 is turned anticlockwise, the faster the vehicle is lowered. Therefore you should proceed very cautiously at first in order to get a feeling for the correct speed.

Use/Cleaning and Care/Maintenance and storage

☐ Lower the support plate 1 until it is no longer loaded. Then pull the vehicle jack out from under the vehicle. Press down on the support plate 1 until it is fully lowered.
☐ Close the release valve 5 by turning the rod 7 on the release valve 5 clockwise.
☐ Take the rod 7 off the release valve 5.
☐ If it is extended, screw the extension screw 2 back down into the jack body.

● Cleaning and Care

□ Liberally grease all external moving parts.
□ Clean the hydraulic trolley jack using a slightly oily cloth.
□ Never use harsh or corrosive cleaning agents.

● Maintenance and storage

● Topping up the hydraulic oil / greasing

Note: Use only hydraulic oil that complies with ISO VG 15.

□ Stand the vehicle jack upright on a level, flat surface.
☐ Screw the extension screw 2 completely down into the jack body.
Place the rod 7 with oval opening on to the release valve 5 and turn the rod anticlockwise (Fig. A) until the support plate 1 is fully lowered.
☐ Pull the oil plug 8 out of the oil reservoir.
☐ Introduce hydraulic oil from a suitable vessel into the oil reservoir. Fill the hydraulic oil reservoir up to the bottom edge of the filling opening.
☐ Remove any air present in the hydraulic system. To do this follow steps 3 - 4 in section on "Removing air from the system".
☐ Replace the oil plug 8 back into the oil reservoir opening.
□ Grease all moving parts on the vehicle jack regularly to prevent corrosion.
☐ Top up with approximately 180 - 190 ml oil if all the oil has been used up.

- Removing air from the hydraulic system

Air in the hydraulic system may detrimentally affect the proper functioning of the vehicle jack.

Proceed as follows to remove air from the hydraulic system:

1. Place the rod 7 with oval opening on to the release valve 5 and turn the rod anticlockwise (Fig. A) until the support plate 1 is fully lowered.
2. Pull the oil plug 8 out of the oil reservoir.
3. Guide the lifting handle 6 into the lifting handle socket 3 and pump it up and down several times to allow any air to escape.
4. Place the rod 7 with oval opening on to the release valve 5 and turn the rod clockwise (Fig. A). The release valve 5 is now closed again.
5. Replace the oil plug 8 back into the oil reservoir opening.
6. If necessary, repeat steps 1 - 5 until all the air has escaped.

- Storing

Place the rod 7 with oval opening on to the release valve 5 and turn the rod anticlockwise (Fig. A) until the support plate 1 is fully lowered.
☐ Screw the extension screw 2 completely down into the jack body.
Store the hydraulic vehicle jack and the lifting handle in a dry environment and protected from moisture.
☐ Ensure that the rod 7 is fully lowered and the extension screw 2 is completely screwed in before you put away the vehicle jack. This will prevent the oil escaping from the oil plug 8.
☐ Grease all moving parts on the vehicle jack regularly to prevent corrosion.

Troubleshooting / Disposal / Informations

● Troubleshooting

● = Fault

© = Cause

O = Remedy

● = The vehicle jack does not raise the vehicle at all or does not raise it high enough.

- = The release valve5 was not properly closed.

O = Close the release valve 5 completely (see the section on "Raising the vehicle").

●=There is not enough hydraulic oil in the vehicle jack.

O = Top up the hydraulic oil (see the section on "Topping up the hydraulic oil / greasing").

- =There is too much hydraulic oil in the cylinder.

O = Remove the excess quantity of hydraulic oil from the cylinder.

- = There is air in the hydraulic system.

O = Remove the air in the hydraulic system (see the section on "Removing air from the hydraulic system").

● = The vehicle jack gives way under load.

- = The release valve5 was not properly closed.

O = Close the release valve 5 completely (see the section on "Raising the vehicle").

● = Hydraulic oil escapes.

- =There is too much hydraulic oil in the cylinder.

O = Remove the excess quantity of hydraulic oil from the cylinder.

● = The pump mechanism works only partially.

- =There is too much hydraulic oil in the cylinder.

O = Remove the excess quantity of hydraulic oil from the cylinder.

- = There is air in the hydraulic system.

O = Remove the air in the hydraulic system (see the section on "Removing air from the hydraulic system").

- Disposal

The packaging and ancillary packing consist entirely of environmentally-friendly materials. They can be disposed of at your local recycling facility.

In the interest of the environment, do not throw out the product with your household refuse. Take it to a suitable centre where it can be disposed of properly. Your local council will be able to tell you where the collection centres are located and their opening times.

Dispose of the hydraulic oil in an environmentally compatible manner. Ask your local repair garage to see to its disposal or find your nearest waste materials collection centre.

- Informations

● Declaration of Conformity

We, Milomex Ltd., c / o Milomex Services, Hilltop Cottage, Barton Road, Pulloxhill, Bedfordshire, MK45 5HP, UK, hereby declare under our sole responsibility that the product: Hydraulic Bottle Jack, Model No.: Z30544, Version: 05 / 2011, to which this declaration refers, complies with the standards / normative documents of 2006/42/EC.

Related harmonised standard: EN 1494 / A1:2008

Heavnerstirling

Description of product:

Hydraulic Bottle Jack

Model no.: Z30544

Version: 05/2011

CE

8 GB/IE

ULTIMATE SPEED

Johdanto

● = Fel
© = Orsak
O = Åtgärd

● = Fehler
© = Ursache
O = Behebung