Question 1

How to reduce the bass on the ALPINE i209?

Accepted Answer

To reduce the bass on your ALPINE i209, you have two main options:

Quick method via the main screen

Press the down arrow on the main screen to access Sound Setup
Select Tone Adjustment mode
Adjust the Bass Level downwards (range: -14 to +14, the default setting is 0)

Via the menu

Press MENU
Navigate to [Setup] then [General] then [Sound]
Select Balance/Fader and reduce the bass slider downwards

BASS ENGINE SQ mode

If you are using the BASS ENGINE SQ mode, you can select a preset type (Standard, Punch, Rich, Mid Bass, or Low Bass) and reduce the BASS ENGINE Level (range 0 to 6) to decrease the intensity of the bass.

Important: Adjusting the bass will not work if the Defeat mode is set to "On" - make sure it is turned off beforehand.

Question 2

How to reset the ALPINE PXA-H700 audio processor to factory settings?

Accepted Answer

To reset your ALPINE PXA-H700 audio processor to factory settings, follow these simple steps:

Turn off the device: Make sure the processor is completely powered off before you begin.
Locate the reset button: On the PXA-H700, there is a small hole marked "Reset", usually located at the back or on the side of the device.
Use a thin, pointed object: Take a straightened paperclip or a fine pen and gently insert it into the reset hole.
Press and hold the button: Press and hold the reset button for about 5 seconds, until you notice the device restarting or the indicators flashing.
Release the button: Once the restart is complete, release the button. The device is then reset to factory settings.

This operation restores the original settings, which can be useful in case of malfunction or to start with a clean configuration.

Question 3

How to access the settings of the Alpine IDA-X300 car radio?

Accepted Answer

To access the settings of your Alpine IDA-X300 car radio, follow these simple steps:

Turn on the car radio: Make sure the device is powered on.
Access the main menu: Press the Menu or Setup button located on the device's control panel.
Navigate the menu: Use the navigation buttons (arrow keys or dial) to scroll through the options displayed on the screen.
Select the “Settings” option: Once this option is highlighted, confirm by pressing the selection button.
Modify the desired settings: You can adjust various settings such as the equalizer, volume, audio settings, and other preferences.
Save your changes: Some options require you to confirm or save the changes; follow the on-screen instructions to finalize.

This procedure allows you to easily customize the settings of your Alpine IDA-X300 car radio for an optimal audio experience.

Question 4

What is the wiring diagram for the ALPINE IVA-D310R car radio?

Accepted Answer

The wiring diagram for the ALPINE IVA-D310R car radio consists of two connectors: the ISO connector for battery/ignition and the tuner box. Here are the essential connections to be strictly followed to ensure proper functioning and avoid short circuits.

Power supply: The yellow wire (battery) must be connected to the positive (+) terminal of the vehicle's battery to memorize settings and provide permanent power to the device. The red wire (switched power) connects to an open terminal on the vehicle's fuse box or another 12V source that only works when the ignition is on or in accessory position, ensuring the car radio turns off with the engine. The black wire (ground) must be securely attached to a proper ground point on the vehicle's chassis, preferably on bare metal. This connection is crucial: use the provided sheet metal screw to tighten the wire securely.

Speaker connections: The car radio has four pairs of speaker output wires. Follow these color codes: front left speaker (white positive / white-black negative), front right speaker (gray positive / gray-black negative), rear left speaker (green positive / green-black negative), and rear right speaker (purple positive / purple-black negative). Polarity is essential: always connect the positive (+) wire to the positive terminal of the speaker and the negative (-) wire to the negative terminal. Incorrect polarity would result in audible phase cancellation and poor sound quality.

Additional functions: The blue wire (electric antenna control) connects to the +B terminal of your powered antenna, if applicable. The blue-white wire (remote power on) should be connected to the power-on wire of an external amplifier or signal processor. The white-brown wire is for remote control: the input wire and output wire must be connected to allow control of the device. The pink-black wire (audio interruption) connects to the output wire of the remote control of another external Alpine device.

Vehicle special functions: The yellow-blue wire (handbrake) must be connected to the powered handbrake wire when the brake is engaged; this allows certain video functions to be disabled when the vehicle is stationary. The orange-white wire (reverse signal) connects to the positive side of the vehicle's reverse light and allows the rear camera to display automatically when shifting into reverse (R). The white-pink wire (monitor control) should be connected to the control wire of the rear touch panel monitor.

Important recommendations: Properly identify the terminals of the ISO connector before proceeding with the wiring. Route all wires at least 10 cm away from the vehicle's electrical harness and keep the battery power wires as far away from other wires as possible to avoid interference. After installation, check that all connections are tight and no wires are exposed. If you are using compatible Ai-NET external devices (CD changer, equalizer, DVD player), connect them via the Ai-NET connector according to the specific diagram provided with those devices. A correct installation ensures not only the optimal functioning of the ALPINE IVA-D310R car radio but also the electrical safety of your vehicle.

User manual ALPINE : user manuals and guides in PDF

Models ALPINE most viewed

Browse manuals ALPINE by appliance type

Recent questions about devices ALPINE