Q: The robot does not start even after adjusting the speed and pressing Power

The Gorenje SBR1000BE has a safety system that prevents starting if the attachment is not properly locked . That is why the Power button does not respond. Here’s what to do: Place the attachment on the motor block aligning the markers Turn the attachment clockwise until you hear a distinct click - that’s the locking Once the click is heard, the attachment is fully secured Only after: set the desired speed (6 speeds available) and press the Power button If the click does not occur or if the robot remains inactive after following these steps, check that you are using the correct attachment for this manual and that nothing is blocking the locking mechanism.

Q: What does the SMD program mean on the Gorenje D20M dryer?

SMD stands for "Smart Drying Mode" . It is one of the three main operating modes of the Gorenje D20M dryer. The three main modes: Dryer - classic drying mode Cont. - constant drying mode SMD - smart drying mode The SMD mode is particularly interesting because it operates automatically : the device adjusts the fan speed and drying intensity based on the humidity level detected in the room. Therefore, you do not need to manually adjust the device - it intelligently adapts to your needs.

Q: How to turn off or power down the GORENJE RK6192EX refrigerator?

Stopping the cooling: To stop the cooling, turn the knob A until the arrow is aligned with the stop symbol. The appliance will then enter stop mode. Important: By turning the knob A, the appliance stops cooling but remains powered on - current still flows through the appliance. Complete power down: For a total electrical disconnection, you must unplug the power cord from the wall outlet. This is recommended especially before cleaning or in case of prolonged absence.

Question 1

Red arrow next to the time: stove locked after using the oven

Accepted Answer

The red arrow next to the time indicates that your GORENJE GGI9C20X stove is in safety lock mode. This is a protection that automatically activates after certain cooking modes like the oven.

To unlock your stove:

Locate the button with the key symbol on the control panel (usually located at the bottom or on the side of the controller)
Press and hold this button for 3 to 5 seconds until the red arrow disappears
Your stove should then become operational again

If the arrow persists after this action:

Completely turn off the appliance at the main switch for 30 seconds
Turn it back on and try to unlock with the key button
Wait a few seconds before restarting a cooking function

This locking is normal and is part of the safety systems integrated into your GORENJE GGI9C20X to prevent the accidental use of the oven and stove simultaneously.

Question 2

How to remove and clean the glass door of the Gorenje BOS6747A01BG oven?

Accepted Answer

To remove and clean the glass door of your Gorenje BOS6747A01BG oven, follow the steps below:

Removing the door

Open the door fully
Turn the two safety levers 90° towards the door
Slowly close the door to about 45°
Lift the door and disengage it from the hinges

Removing the glass panels

Remove the air guide by pulling it towards you
Hold the glass panel by the top edge and carefully remove it
Repeat the process for each glass panel if your model has multiple

Cleaning

Use a mild detergent and a non-abrasive sponge to clean the glass panels. Avoid harsh products or abrasive materials that could scratch the glass.

Reinstallation

Follow the reverse order to put the glass panels and the door back in place. Ensure that the notches of the hinges align correctly before closing the door.

Important notice: The door hinge closes with considerable force. Always turn both safety levers to the support position before removing or installing the door.

Question 3

How do I stop the beeping of the oven once it has reached the temperature?

Accepted Answer

When your GORENJE BO75SYW oven reaches the programmed temperature during preheating, an intermittent sound signal will sound to alert you. This is a normal and intentional behavior of the oven.

To stop the beeping: simply turn the selector knob. The sound alarm will stop immediately.

This preheating signal lets you know that the oven is ready for cooking. After stopping the beeping, you can place your food in the oven.

Question 4

The robot does not start even after adjusting the speed and pressing Power

Accepted Answer

The Gorenje SBR1000BE has a safety system that prevents starting if the attachment is not properly locked. That is why the Power button does not respond.

Here’s what to do:

Place the attachment on the motor block aligning the markers
Turn the attachment clockwise until you hear a distinct click - that’s the locking
Once the click is heard, the attachment is fully secured
Only after: set the desired speed (6 speeds available) and press the Power button

If the click does not occur or if the robot remains inactive after following these steps, check that you are using the correct attachment for this manual and that nothing is blocking the locking mechanism.

Question 5

How do I empty the condensation tank of my GORENJE KAM35 T air conditioner when it is full?

Accepted Answer

To empty the condensation tank of your GORENJE KAM35 T air conditioner, follow this procedure:

Manual Drainage

Turn off the device and unplug it from the power supply
Locate the main drainage plug ("Główny korek spustowy" in Polish)
Remove the cover and the plug from the main drainage connection
Let the water drain completely from the drainage opening
Replace the plug and the cover

Important for Heating Modes

If your device is operating in heat pump mode (heating), connect a drainage hose to the main connection point to ensure continuous drainage. The hose should be routed horizontally and positioned lower than the device's connection point to avoid backflow.

Error Code E5

If the screen displays the symbol "E5", it means that the condensation tank is full. The device will stop operating until you perform a manual drainage.

Question 6

How to start the GORENJE BM251S7XG?

Accepted Answer

To start your GORENJE BM251S7XG, follow these steps:

Quick Start (1 minute)

Place the food in the center of the turntable
Close the door
Press the Start/Reset button

The appliance will automatically heat at maximum power for 1 minute, then emit 5 beeps.

Start with Custom Duration

Use the 1 MIN and 10 SEC buttons to set the desired duration
If you want to change the power, press Micro...Auto menu to select the mode
Press Start/Reset to begin cooking

Question 7

How does the recirculation mode work and how to install the charcoal filters on both sides of the grille?

Accepted Answer

Recirculation mode and charcoal filters

The recirculation mode of the GORENJE WHI629EB hood filters the cooking air and returns it to the kitchen, without the need for an external exhaust duct.

How the recirculation mode works:

The recirculation mode uses charcoal filters to neutralize cooking odors
These filters must be replaced every 4 months with regular use
Unlike the grease filter which can be cleaned, the charcoal filter cannot be washed or regenerated

Installation of the two charcoal filters:

Your hood is equipped with two charcoal filter slots, one on each side of the motor grille
The two filters are placed symmetrically to ensure uniform air filtration
Insert them firmly into their respective slots until you feel resistance
Replace both filters together when maintenance is due

To check the exact positioning and visualize the installation, refer to the installation diagram in the PDF of the manual above.

Question 8

What does the SMD program mean on the Gorenje D20M dryer?

Accepted Answer

SMD stands for "Smart Drying Mode". It is one of the three main operating modes of the Gorenje D20M dryer.

The three main modes:

Dryer - classic drying mode
Cont. - constant drying mode
SMD - smart drying mode

The SMD mode is particularly interesting because it operates automatically: the device adjusts the fan speed and drying intensity based on the humidity level detected in the room. Therefore, you do not need to manually adjust the device - it intelligently adapts to your needs.

Question 9

How to disassemble and take apart this GORENJE NeoExpert vacuum cleaner?

Accepted Answer

This GORENJE NeoExpert SVC296749NEBL vacuum cleaner can be disassembled to access the various components (filters, tank, brush) during maintenance or servicing. Here are the main steps:

Dust container

Remove the hose from the motor unit
Press the button located at the front of the tank to open it

Filters

Intake filter: pull on the filter handle to safely remove it from the ring
Exhaust filter: turn the display counterclockwise to access the internal filter of the motor unit

Floor brush

A button located at the back of the brush allows you to remove the roller

Compact motorized brush

A small button located on the side of the brush can be turned to release and slide it out of the slot

Battery

Press the battery button and remove it from the portable unit

Refer to the accompanying illustrations in the manual for each disassembly step.

Question 10

How to turn off or power down the GORENJE RK6192EX refrigerator?

Accepted Answer

Stopping the cooling: To stop the cooling, turn the knob A until the arrow is aligned with the stop symbol. The appliance will then enter stop mode.

Important: By turning the knob A, the appliance stops cooling but remains powered on - current still flows through the appliance.

Complete power down: For a total electrical disconnection, you must unplug the power cord from the wall outlet. This is recommended especially before cleaning or in case of prolonged absence.

User manual GORENJE : user manuals and guides in PDF

Models GORENJE most viewed

Browse manuals GORENJE by appliance type

Recent questions about devices GORENJE