Q: I forgot my code - how do I open my SentrySafe SFW123GDC safe?

Don't panic! The SentrySafe SFW123GDC has a permanent 5-digit factory code that can never be deleted and always works, even if you have forgotten your personal code. Locate the factory code The code is printed on the back of the owner's manual provided with your safe. Check: The original box The documentation that came with it Your purchase or registration papers Open the safe with the factory code Once you have the code, proceed as follows: Enter the 5-digit factory code on the keypad Wait for the green light to turn on You have 4 seconds to turn the handle down to open Reprogram a new code Once the safe is open, you can create a new personal code. Refer to the section "Programming a new code" in your manual for the precise steps. If you don't have the manual If you registered your safe at www.registermysafe.com , you can retrieve your factory code from your account. Otherwise, contact SentrySafe directly with proof of purchase.

Question 1

I forgot my code - how do I open my SentrySafe SFW123GDC safe?

Accepted Answer

Don't panic! The SentrySafe SFW123GDC has a permanent 5-digit factory code that can never be deleted and always works, even if you have forgotten your personal code.

Locate the factory code

The code is printed on the back of the owner's manual provided with your safe. Check:

The original box
The documentation that came with it
Your purchase or registration papers

Open the safe with the factory code

Once you have the code, proceed as follows:

Enter the 5-digit factory code on the keypad
Wait for the green light to turn on
You have 4 seconds to turn the handle down to open

Reprogram a new code

Once the safe is open, you can create a new personal code. Refer to the section "Programming a new code" in your manual for the precise steps.

If you don't have the manual

If you registered your safe at www.registermysafe.com, you can retrieve your factory code from your account. Otherwise, contact SentrySafe directly with proof of purchase.

Question 2

The handle of the SFW123GDC safe is stuck and won't lift - how can I unlock it?

Accepted Answer

If the handle of your SentrySafe SFW123GDC safe won't lift and seems stuck, here are the solutions according to the manufacturer's manual:

Solution 1: Reposition the handle to the horizontal position

Before any unlocking, the handle must be in the horizontal position. Turn it up or down until it clicks properly into the horizontal position. This is a mandatory step.

Solution 2: Apply force in the opposite direction

If you have applied excessive force on the handle, the internal mechanism may have disengaged from the locking bolts. In this case, push upwards until you feel a

Question 3

How do I properly lock my SentrySafe SFW123GDC safe?

Accepted Answer

Here are the steps to properly lock your SentrySafe SFW123GDC safe:

Locking Steps

Close the door of the safe completely
Pull the handle up until it is horizontal. For waterproof models, apply slight pressure on the front left side before turning the handle
Turn the dial at least 2 times to the right (clockwise) to activate the combination mechanism
If your model has a key lock, insert the key, turn it to the locked position, and then remove the key

Important point: The handle must be completely horizontal to ensure proper engagement of the locking mechanism. If you have difficulty pulling the handle, check that the door is fully closed before trying again.

Question 4

How to reposition the bolts of the DSW5840 when the door is open?

Accepted Answer

If the bolts of the DSW5840 do not fit properly when the door is open, first check the alignment between the safe and the floor holes.

Correct installation procedure

According to the manual, the installation of the fixing bolts is done as follows:

The safe must be positioned on its right side, with the horizontal hinges to access the feet
Drill holes through the indentations of the feet (not through the back) with a 7/16 inch (11 mm) drill
The holes must be perpendicular to the bottom of the safe

Reasons for bolt blockage

If the bolts do not fit:

Lack of alignment - Ensure that the safe is resting flat and that the indentations of the feet are directly above the floor holes
Misaligned bolts - A slight offset completely blocks insertion. You may need to slightly tilt the safe to realign it
Inaccurate floor hole - Make sure that the floor holes match the required dimensions (9/32 inch for wood, 3/8 inch for concrete)

Solution: With the door open, visually check that each foot aligns perfectly with its hole before inserting the bolts. A simple lateral rocking of the safe is often enough to correct the offset.

Question 5

How do I change the access code of my SentrySafe SFW123TTC safe?

Accepted Answer

To change your access code on the SentrySafe SFW123TTC, follow these steps:

Program a new user code:

Touch the safe's keypad to activate it
Enter the factory code "PROG" (you will find it on the back of the user manual)
Wait for the programming light to blink
Enter your new 5-digit code

Delete the old code:

If you also want to erase your old code, touch the keypad, enter "PROG", wait for the blinking, then type "00000". Warning: the safe will not indicate the deletion of the code - test it to confirm that the old code no longer works.

Secondary code:

You can also program a secondary code by entering: "PROG" - "PROG" - your currently programmed user code, followed by your new 5-digit code.

Important: The factory code "PROG" always remains active and cannot be changed.

User manual SentrySafe : user manuals and guides in PDF

Models SentrySafe most viewed

Browse manuals SentrySafe by appliance type

Recent questions about devices SentrySafe