Q: Why won't my Hendi 219911 oven start? How do I turn it on?

If your Hendi 219911 oven won't start, first check the power supply : Make sure the oven is plugged into a 230 V / 50 Hz outlet Check that the outlet is working by testing another device Ensure that your electrical installation has a 16 A circuit breaker (recommended for this appliance which consumes 2.5 kW) To start the oven: Turn the rotary thermostat to the desired temperature (between 50 and 300 °C) The indicator light should turn on and off once the temperature is reached You can also set the mechanical timer for up to 120 minutes if necessary If the light still does not turn on after these checks, the problem is likely with the power supply or an internal failure. Test with another outlet, check the fuses/circuit breakers, and contact a technician if the problem persists. The Hendi 219911 has an automatic thermal protection that can stop the appliance in case of overload.

Q: How to fix if the door of the Hendi 219911 oven does not close?

The Hendi 219911 oven features a removable double-glazed door for easy cleaning. If the door does not close properly, here are the points to check: Check that nothing is blocking the closure - Food residues, grease, or debris may prevent the door from closing completely. Clean the seal and the areas around the frame. Check the alignment of the door - Ensure that the door is properly aligned with the oven frame. Check that the hinges are not damaged or misaligned. Check the optional lock - The oven may be equipped with an optional door lock (not included as standard). If this lock is installed, make sure it is functioning correctly and is not blocked. Reassemble the door if necessary - Since the door is removable for cleaning, it may have been reassembled incorrectly. Ensure that all components are in place. If the problem persists after these checks, it may be a mechanical defect covered by the oven's 2-year warranty. Contact Hendi customer service for assistance.

Q: Can you enter the pager number directly instead of scrolling?

Yes, you can enter the pager number directly. On the Hendi 201633, you do not have to scroll through the history or navigate through the menus to call a pager. In normal operating mode, simply: Enter the corresponding number displayed on the pager (between 1 and 998) Press the Call button to trigger the call immediately This method is faster than scrolling through call histories or navigating through programming modes F1-F5. The transmitter's display panel will show the entered number, allowing you to confirm your selection before validating the call.

Q: How to set the alarm signal duration on the Hendi 201633?

To set the alarm signal duration on the Hendi 201633, follow these steps: Press the FUNCTION button Use the UP/DOWN buttons to navigate to F3 Press CALL to enter this mode The screen will then display L015 (default value of 15 seconds) Enter the desired number of seconds Press CALL to confirm your choice You can program an alarm duration between 1 and 999 seconds (up to about 16-17 minutes). This allows you to precisely control how long the alarm signal remains active before it automatically stops.

Q: How to call or ring a receiver with the Hendi 201633 system?

To ring a receiver with the Hendi 201633 system, use the Call button located on the transmission unit (TX). This button allows you to initiate a call to an individual receiver or to a group of receivers. You can customize the type of alert emitted on the receivers using the function key F2 : Sound only Vibration only LED flashing only Combinations: sound + vibration, vibration + LED, sound + LED, or all three at once The duration of the alert can be adjusted via the functions F1 to F3 (adjustable from 1 to 999 seconds), and you can configure call repetition intervals with the key F4 .

Question 1

Why won't my Hendi 219911 oven start? How do I turn it on?

Accepted Answer

If your Hendi 219911 oven won't start, first check the power supply:

Make sure the oven is plugged into a 230 V / 50 Hz outlet
Check that the outlet is working by testing another device
Ensure that your electrical installation has a 16 A circuit breaker (recommended for this appliance which consumes 2.5 kW)

To start the oven:

Turn the rotary thermostat to the desired temperature (between 50 and 300 °C)
The indicator light should turn on and off once the temperature is reached
You can also set the mechanical timer for up to 120 minutes if necessary

If the light still does not turn on after these checks, the problem is likely with the power supply or an internal failure. Test with another outlet, check the fuses/circuit breakers, and contact a technician if the problem persists. The Hendi 219911 has an automatic thermal protection that can stop the appliance in case of overload.

Question 2

How to fix if the door of the Hendi 219911 oven does not close?

Accepted Answer

The Hendi 219911 oven features a removable double-glazed door for easy cleaning. If the door does not close properly, here are the points to check:

Check that nothing is blocking the closure - Food residues, grease, or debris may prevent the door from closing completely. Clean the seal and the areas around the frame.
Check the alignment of the door - Ensure that the door is properly aligned with the oven frame. Check that the hinges are not damaged or misaligned.
Check the optional lock - The oven may be equipped with an optional door lock (not included as standard). If this lock is installed, make sure it is functioning correctly and is not blocked.
Reassemble the door if necessary - Since the door is removable for cleaning, it may have been reassembled incorrectly. Ensure that all components are in place.

If the problem persists after these checks, it may be a mechanical defect covered by the oven's 2-year warranty. Contact Hendi customer service for assistance.

Question 3

How to fill the detergent and rinse aid in the Hendi 231753 dishwasher?

Accepted Answer

The Hendi 231753 machine uses two peristaltic pumps to automatically dispense detergent and rinse aid. Here is the exact operation:

Filling System

Two hoses must be immersed in the appropriate tanks:

Detergent Hose - pump dispenses 0.83 ml per second
Rinse Hose - pump dispenses 0.19 ml per second

Default Filling Durations

At startup (first filling):

Detergent: 180 seconds = approximately 149 ml
Rinse aid: 35 seconds = approximately 6.7 ml

After each cycle (additional fillings):

Detergent: 13 seconds = approximately 10.8 ml
Rinse aid: 12 seconds = approximately 2.3 ml

Adjusting the Doses

You can modify these durations via the user menu. Press the SW1 + SW3 + SW6 buttons simultaneously for 3 seconds (door closed) to access the dF (initial detergent), c.c. (detergent per cycle), rF (initial rinse), and re (additional rinse) settings. Adjust with SW1 (increase) and SW2 (decrease), validate with SW5.

Question 4

Why won't my Hendi 210048 slicer start?

Accepted Answer

If your Hendi 210048 slicer won't start, check the following points in order:

1. Check the power supply
Make sure the device is properly plugged into a working outlet 220-240 V / 50 Hz. Test the outlet by plugging in another device to confirm it is functioning correctly. Inspect the power cord for any cuts, wear, or visible damage.

2. Check the blade guard placement
The slicer has micro-switches (SQ1, SQ2) that automatically block the device if the blade guard is not properly positioned. Ensure that the blade guard is fully in place and securely locked. The guard must be in the stop position.

3. Check the carriage lock
Make sure the carriage is properly locked. This mechanical safety must be engaged for the device to operate.

4. Restart after a power outage
The slicer is equipped with a relay (KC) in the control box that forces an automatic restart in case of a power cut. If you have just experienced a power outage: unplug the device completely for 10 seconds, then plug it back in. Then press the white button marked “I” (ON position) on the ON/OFF switch to activate the device.

5. Press the start button correctly
Make sure the switch is positioned so that the white button “I” is accessible to you. Press this button fully to start the blade.

If none of these checks allow for starting, the device may have an internal failure (electrical issue, motor, relay, or electronic board). In this case, stop using it immediately and contact an authorized Hendi service center. Your slicer is covered by a 12-month warranty in case of proper use.

Question 5

Can you enter the pager number directly instead of scrolling?

Accepted Answer

Yes, you can enter the pager number directly. On the Hendi 201633, you do not have to scroll through the history or navigate through the menus to call a pager.

In normal operating mode, simply:

Enter the corresponding number displayed on the pager (between 1 and 998)
Press the Call button to trigger the call immediately

This method is faster than scrolling through call histories or navigating through programming modes F1-F5. The transmitter's display panel will show the entered number, allowing you to confirm your selection before validating the call.

Question 6

How to set the alarm signal duration on the Hendi 201633?

Accepted Answer

To set the alarm signal duration on the Hendi 201633, follow these steps:

Press the FUNCTION button
Use the UP/DOWN buttons to navigate to F3
Press CALL to enter this mode
The screen will then display L015 (default value of 15 seconds)
Enter the desired number of seconds
Press CALL to confirm your choice

You can program an alarm duration between 1 and 999 seconds (up to about 16-17 minutes). This allows you to precisely control how long the alarm signal remains active before it automatically stops.

Question 7

Can the volume of the ringtone be increased or decreased on the Hendi 201633?

Accepted Answer

No, the ringtone volume is not adjustable on the Hendi 201633. This paging system does not include a volume control function for sound alarms. The sound level is set by default and cannot be modified through the transmitter settings.

However, you can fully customize how the pagers receive the alert using the F2 (Set alarm mode) function. You have the choice of 7 distinct alarm modes:

Mode 1: Sound only (beep) – quick access with code 004
Mode 2: Vibration only – code 005
Mode 3: LED only (flashing) – code 006
Mode 4: Sound + Vibration – code 007
Mode 5: Vibration + LED – code 008
Mode 6: Sound + LED – code 009
Mode 7: Sound + Vibration + LED (all three) – code 010

You can also adjust two other important parameters to tailor the alert to your environment:

Alarm duration (F3): set the duration between 1 and 999 seconds
Repeat interval (F4): configure the frequency at which the pager retransmits the alarm if it is not confirmed

If you need a more discreet notification, prefer modes with vibration or LED rather than sound mode. This allows you to reduce sound disturbance while maintaining an effective alert system. In noisy environments (kitchen, restaurant area), vibration mode is particularly recommended.

Question 8

How to configure the pager to vibrate and light up with LED?

Accepted Answer

The Hendi 201633 system allows you to combine vibration and LED lighting via the F2 function for programming alert modes.

To activate this mode:

Access the F2 function on the control unit
Select the combination vibration + LED from the seven available modes
Confirm your choice

The system offers seven different alarm combinations: sound only, vibration only, LED only, sound + vibration, vibration + LED, sound + LED, or all three combined (sound + vibration + LED). You can adjust the mode according to your operational needs.

Question 9

How to configure the pager to vibrate only?

Accepted Answer

To configure the Hendi 201633 system pager to vibration mode only, you need to access the F2 menu and enter the code 005. Here is the exact procedure:

Press the FUNCTION button
Use the UP/DOWN buttons to navigate to F2 (alarm mode configuration menu)
Press the CALL button to confirm
Dial the code 005 on the numeric keypad and press CALL

Once this configuration is applied, the pagers on charge will display mode A002 and will activate exclusively by vibration, without sound or LED. Incoming calls will trigger only the vibration.

If you wish to change the alarm mode later, here are the other options available in the F2 menu:

Code 004: sound only
Code 006: LED only
Code 007: sound + vibration
Code 008: vibration + LED
Code 009: sound + LED
Code 010: sound + vibration + LED
Code 000: alarm disabled

Note: the pagers must be on charge during configuration for the settings to be applied correctly.

Question 10

How to call or ring a receiver with the Hendi 201633 system?

Accepted Answer

To ring a receiver with the Hendi 201633 system, use the Call button located on the transmission unit (TX). This button allows you to initiate a call to an individual receiver or to a group of receivers.

You can customize the type of alert emitted on the receivers using the function key F2:

Sound only
Vibration only
LED flashing only
Combinations: sound + vibration, vibration + LED, sound + LED, or all three at once

The duration of the alert can be adjusted via the functions F1 to F3 (adjustable from 1 to 999 seconds), and you can configure call repetition intervals with the key F4.

User manual Hendi : user manuals and guides in PDF

Models Hendi most viewed

Browse manuals Hendi by appliance type

Recent questions about devices Hendi