Q: How to set the torque to 4 Nm on the MAKITA DF331DSAE?

To set a torque of 4 Nm on your MAKITA DF331DSAE, turn the adjustment ring located at the back of the chuck until the corresponding graduation aligns with the tool's arrow . The tool has 19 adjustment levels (levels 1 to 18, plus one drilling position) that allow for progressively increasing torque. The exact torque of 4 Nm depends on the type of screw and the material used. The manual provides a correspondence table between the levels and screw sizes, but the precise setting may vary depending on your application. Practical tip: Before starting your work, perform a screwing test in a material of the same type to determine the exact level that allows you to reach 4 Nm of torque without overloading the clutch.

Q: How to use the switch to switch to hammer mode on the Makita HP1630 drill?

The Makita HP1630 hammer drill features a mode change lever that allows you to easily switch between regular drilling and hammer drilling. This lever is located on the main body of the drill and has two symbols: a rotation (⊖) for normal mode and a hammer (⊕) for hammer mode. To activate hammer mode: Always turn off the drill before changing the mode Locate the mode change lever on the body of the drill Slide the lever all the way to the right until it reaches the hammer symbol (⊕) Ensure that the lever is in the final position - an intermediate position could damage the tool To return to normal drilling mode: Turn off the drill Slide the lever all the way to the left until it reaches the rotation symbol (⊖) Hammer mode is exclusively used on hard materials such as concrete, brick, and stone. For other materials (wood, metal, ceramics, plastics), keep the lever in the rotation-only position to optimize the lifespan of your HP1630 and ensure better drilling quality.

Q: How to unlock the chuck of the Makita HP2071 percussion drill when it is stuck and no longer turns?

The Makita HP2071 percussion drill is equipped with a keyless chuck (with a ring and sleeve). During normal use, you should grasp the ring and turn the sleeve counterclockwise to open the jaws, then clockwise to tighten after inserting the drill bit. If the chuck is stuck because a drill bit is jammed in the jaws and you cannot loosen it with the sleeve alone, the official Makita manual prescribes the following procedure: Firmly grasp the handle of the chuck with a pair of pliers or a similar tool. Important: do not grasp by the fixing ring , only by the cylindrical handle. Place an appropriate wrench (19mm wrench, adjustable wrench, or equivalent) on the hex nut located at the front of the chuck (visible under the chuck). Turn the wrench clockwise to gradually loosen the stuck chuck. This procedure uses the leverage effect of the wrench on the hex nut to create sufficient loosening force. The wrench should be proportionate to the diameter of the hex nut for safety and efficiency. If after this operation the chuck remains stuck, it is recommended to consult a Makita after-sales service center to avoid permanently damaging the chuck mechanism. Do not apply excessive force with the wrench, as this could deform the nut or break the internal jaws of the chuck.

Question 1

How to set the torque to 4 Nm on the MAKITA DF331DSAE?

Accepted Answer

To set a torque of 4 Nm on your MAKITA DF331DSAE, turn the adjustment ring located at the back of the chuck until the corresponding graduation aligns with the tool's arrow.

The tool has 19 adjustment levels (levels 1 to 18, plus one drilling position) that allow for progressively increasing torque. The exact torque of 4 Nm depends on the type of screw and the material used. The manual provides a correspondence table between the levels and screw sizes, but the precise setting may vary depending on your application.

Practical tip: Before starting your work, perform a screwing test in a material of the same type to determine the exact level that allows you to reach 4 Nm of torque without overloading the clutch.

Question 2

How to use the Makita HR2641 drill?

Accepted Answer

To use the Makita HR2641 drill safely and effectively, follow these steps:

1. Preparation and safety

Wear protective equipment, including safety glasses and gloves.
Check that the drill is in good condition and that the bits are suitable for the material to be drilled.

2. Power supply

For a corded model, plug the drill into a suitable electrical outlet.
For a cordless model, ensure that the battery is charged and properly inserted.

3. Mode selection

The Makita HR2641 has several modes (simple drilling, hammer drilling, chiseling). Choose the appropriate mode based on your task using the mode selector.

4. Inserting the bit

Open the chuck by turning it counterclockwise.
Insert the bit and then tighten the chuck by turning it clockwise.

5. Speed adjustment

Adjust the speed according to the material: low speed for hard materials, high speed for soft materials.

6. Drilling

Position the drill at the desired angle.
Apply moderate and constant pressure, allowing the drill to work without forcing it.

7. After use

Release the trigger and remove the drill from the hole.
Clean the area if necessary and store the tool in a dry place.

8. Maintenance

Regularly clean the drill and check the condition of the bits and chuck.

Question 3

How to use the switch to switch to hammer mode on the Makita HP1630 drill?

Accepted Answer

The Makita HP1630 hammer drill features a mode change lever that allows you to easily switch between regular drilling and hammer drilling. This lever is located on the main body of the drill and has two symbols: a rotation (⊖) for normal mode and a hammer (⊕) for hammer mode.

To activate hammer mode:

Always turn off the drill before changing the mode
Locate the mode change lever on the body of the drill
Slide the lever all the way to the right until it reaches the hammer symbol (⊕)
Ensure that the lever is in the final position - an intermediate position could damage the tool

To return to normal drilling mode:

Turn off the drill
Slide the lever all the way to the left until it reaches the rotation symbol (⊖)

Hammer mode is exclusively used on hard materials such as concrete, brick, and stone. For other materials (wood, metal, ceramics, plastics), keep the lever in the rotation-only position to optimize the lifespan of your HP1630 and ensure better drilling quality.

Question 4

How to change the rotation direction (right/left) of the Makita HP1630 drill?

Accepted Answer

The Makita HP1630 percussion drill allows you to change the rotation direction to suit different uses, such as drilling or unscrewing.

Change the rotation direction

Right position (clockwise): used for drilling or screwing.
Left position (counterclockwise): used for unscrewing or removing a stuck bit.

To change the rotation direction, locate the direction switch usually found near the trigger. This switch is a small lever or button that you can move to the right or left:

Make sure the drill is off and unplugged for your safety.
Move the lever to the right for clockwise (right) direction.
Move the lever to the left for counterclockwise (left) direction.
Ensure that the lever is securely engaged in the chosen position before starting.

This function is essential for effectively using the Makita HP1630 drill, especially for screwing or unscrewing without changing tools.

Question 5

How to unlock the chuck of the Makita HP2071 percussion drill when it is stuck and no longer turns?

Accepted Answer

The Makita HP2071 percussion drill is equipped with a keyless chuck (with a ring and sleeve). During normal use, you should grasp the ring and turn the sleeve counterclockwise to open the jaws, then clockwise to tighten after inserting the drill bit.

If the chuck is stuck because a drill bit is jammed in the jaws and you cannot loosen it with the sleeve alone, the official Makita manual prescribes the following procedure:

Firmly grasp the handle of the chuck with a pair of pliers or a similar tool. Important: do not grasp by the fixing ring, only by the cylindrical handle.
Place an appropriate wrench (19mm wrench, adjustable wrench, or equivalent) on the hex nut located at the front of the chuck (visible under the chuck).
Turn the wrench clockwise to gradually loosen the stuck chuck.

This procedure uses the leverage effect of the wrench on the hex nut to create sufficient loosening force. The wrench should be proportionate to the diameter of the hex nut for safety and efficiency.

If after this operation the chuck remains stuck, it is recommended to consult a Makita after-sales service center to avoid permanently damaging the chuck mechanism. Do not apply excessive force with the wrench, as this could deform the nut or break the internal jaws of the chuck.

Question 6

How to remove the drill bit from the Makita HP2071 percussion drill?

Accepted Answer

To remove the drill bit from your Makita HP2071 percussion drill, follow these simple steps:

1. Safety first

Make sure the drill is unplugged from the power source or that the battery is removed to avoid any accidental start.

2. Identify the chuck

The chuck is the part located at the front of the drill that holds the drill bit in place.

3. Loosen the chuck

Keyless chuck: Turn the chuck ring counterclockwise to loosen it.
Keyed chuck: Insert the provided key into the holes of the chuck and turn it counterclockwise to loosen.

4. Remove the drill bit

Once the chuck is loosened, gently pull the drill bit to remove it.

5. Install a new drill bit (optional)

To install a new drill bit, insert it into the chuck and tighten it by turning the ring or the key clockwise until it is securely fastened.

Question 7

How to reposition the flat spring of the speed selector on the Makita 6271D cordless drill?

Accepted Answer

The flat spring of the speed selector on the Makita 6271D drill is a critical component that maintains the selection position between the two speeds (0-400 RPM in low speed and 0-1300 RPM in high speed). This spring often detaches during the disassembly of the casing and must be repositioned carefully to ensure smooth operation.

Before you begin: Always remove the 12V Ni-MH battery from the Makita 6271D before any intervention. Work on a flat and organized surface to avoid losing screws or the spring. Have a screwdriver for the casing screws and a container to store the parts in the order of disassembly.

Accessing the speed selector: The speed selector is located on the top of the transmission casing. Gradually unscrew the casing screws, ensuring to keep them in a secure place. Once the casing is partially open, you will access the speed change lever and the compression springs that hold it in position.

Repositioning the flat spring: The speed change lever has two small compression springs under its assembly. The flat spring must be placed in the designated slot on the lever, with the protrusion of the transmission gear fitting into compression spring number 4. Ensure that the spring is well aligned in its notches and exerts uniform tension without twisting. The spring should keep the lever in its neutral or slightly taut position.

Positioning test: Before completely closing the casing, manually test the lever by slowly moving it between position "1" (low speed) and position "2" (high speed). The movement should be smooth, and the spring should return the lever to the center position without excessive resistance. If the spring does not produce sufficient tension or if the lever remains stuck, the spring is mispositioned and needs to be readjusted.

Reassembly: Once the spring is correctly repositioned, close the casing by gradually screwing the screws back in. Do not force the screws: the casing should close effortlessly once all parts are correctly aligned. Check that no wire or cable is pinched under the casing.

Final check: Reinsert the 12V battery and activate the speed selector several times without pulling the start trigger. Both positions should be clearly distinct, and the lever should not move accidentally during operation. If the spring continues to detach or if the selector does not maintain its position, contact an authorized Makita service center, as a spare part (part number available from Makita) will need to be replaced.

Important: The technical manual for the Makita 6271D states that any repair or maintenance other than battery replacement must be performed by an authorized Makita service center to ensure safety and compliance with the product's 3-year warranty. This intervention is provided for informational purposes only for experienced users in electric tool repair.

Question 8

Which model of carbon brushes is compatible for replacing those of the MAKITA 6381D cordless drill?

Accepted Answer

To replace the carbon brushes of your MAKITA 6381D cordless drill, you need to use the CB-64 brushes (Makita reference 194968-1). There is also a variant under the reference 191627-8 that is perfectly compatible. These brushes are the original Makita wear parts specifically designed for this 14.4V model.

The CB-64 brushes have dimensions of 8 x 5 x 10.8 mm and come as a pair of brushes. They should be replaced together to ensure balanced motor operation. These parts are consumable, and their replacement is part of the normal maintenance of the tool over time.

Before proceeding with the replacement, always remove the battery and unplug the tool. Access the brushes by opening the motor housing according to your drill's manual. During installation, check that the contact springs and brush holders are not damaged, as this would affect the energy transmission to the motor.

We recommend using only original Makita brushes to ensure the durability and reliability of your tool. Lower quality compatible parts could damage the motor. These CB-64 brushes are available from official Makita dealers, on specialized spare parts websites, and at authorized Makita service centers.

If you are not comfortable with this intervention or if the brushes are not easily accessible on your model, we advise you to have this repair done by an authorized Makita service center. According to the official notice, all maintenance work must be carried out with original Makita spare parts to preserve the performance and safety of the device.

User manual MAKITA Drill : user manuals and guides in PDF

Models MAKITA Drill most viewed

Other categories MAKITA

Recent questions about Drill MAKITA