Q: Can any button on the ROBLIN HIGH CONFIDENCE PLUS 900 hood be used?

No, each button has a specific function and is not interchangeable. On the ROBLIN HIGH CONFIDENCE PLUS 900 hood, here is the purpose of each button: Power button: Turns on the extraction motor at the last used speed and turns it off as needed. Speed button: Reduces the extraction speed and activates the charcoal filter saturation alarm in recycling mode. 24h button: Activates the motor for 10 minutes every hour at a speed of 100m³/h for 24 hours (programmed continuous extraction function). Delayed stop button: Allows for automatic motor shutdown after 30 minutes of operation. Lighting button: Decreases or increases the intensity of the hood's lighting. Reset button: To be held for 3 seconds to reset the filter alarm once triggered. Each button must be used for its specific function. Press the one that corresponds to the action you wish to perform.

Q: How do I set the clock on the ROBLIN AQUA 900?

The ROBLIN AQUA 900 does not have a clock function. Although this hood has a digital display , it is not used to set the time but to show the motor status and filter maintenance alerts. The display notably indicates “24” accompanied by a blinking dot when the motor is running. This value indicates the speed or status, not a clock function. The only time-related functions available on this hood are: Delayed stop 30 minutes - allows for a programmed stop of the suction Automatic cycle - operation for a predefined duration Intensive stop 6 minutes - short-term suction boost These functions do not require any time setting; they are activated by a simple press on the touch buttons of the control panel.

Question 1

Why does the FG indicator blink after cleaning the filters?

Accepted Answer

The FG indicator blinks because the system detects that the grease filter (FA) has reached its usage limit of 100 hours. This counter automatically triggers every 100 hours of operation, regardless of cleaning - it is simply a scheduled maintenance reminder, not a failure.

Even after cleaning in the dishwasher (maximum 50°C), the indicator persists because it needs to be manually reset. Cleaning is sufficient to extend the use of the filters (lifetime: 10 years), but the alarm does not turn off by itself.

Reset Procedure

Turn off the motor AND the lighting of the hood
Hold the reset button for 3 seconds
The display will temporarily show "24" with a blinking dot
The alarm will completely disappear

Note: This 100-hour cycle is normal. Continue to clean your filters in the dishwasher regularly (about every month), then simply reset the alarm each time it activates.

Question 2

Can any button on the ROBLIN HIGH CONFIDENCE PLUS 900 hood be used?

Accepted Answer

No, each button has a specific function and is not interchangeable.

On the ROBLIN HIGH CONFIDENCE PLUS 900 hood, here is the purpose of each button:

Power button: Turns on the extraction motor at the last used speed and turns it off as needed.
Speed button: Reduces the extraction speed and activates the charcoal filter saturation alarm in recycling mode.
24h button: Activates the motor for 10 minutes every hour at a speed of 100m³/h for 24 hours (programmed continuous extraction function).
Delayed stop button: Allows for automatic motor shutdown after 30 minutes of operation.
Lighting button: Decreases or increases the intensity of the hood's lighting.
Reset button: To be held for 3 seconds to reset the filter alarm once triggered.

Each button must be used for its specific function. Press the one that corresponds to the action you wish to perform.

Question 3

The ROBLIN HIGH CONFIDENCE PLUS 900 hood works with the keyboard but the remote control no longer responds

Accepted Answer

If the hood works normally with the keyboard but the remote control no longer responds (even with new LR03 1.5V batteries correctly placed), the radio receiver is probably disabled.

To reactivate the remote control:

Press one key on the hood's keyboard for 5 to 6 seconds until the display blinks once
This action toggles the activation/deactivation of the radio receiver
Test the remote control immediately afterwards

Checks before:

LR03 1.5V batteries - check that they are inserted the right way
Point the remote control directly at the hood, not sideways or too far away
The receiver may have disabled itself during a power outage or due to a false manipulation

If the remote control still does not work after this reset, contact ROBLIN customer service at 04 88 78 59 93 to have a technician intervene.

Question 4

How do I set the clock on the ROBLIN AQUA 900?

Accepted Answer

The ROBLIN AQUA 900 does not have a clock function. Although this hood has a digital display, it is not used to set the time but to show the motor status and filter maintenance alerts.

The display notably indicates “24” accompanied by a blinking dot when the motor is running. This value indicates the speed or status, not a clock function.

The only time-related functions available on this hood are:

Delayed stop 30 minutes - allows for a programmed stop of the suction
Automatic cycle - operation for a predefined duration
Intensive stop 6 minutes - short-term suction boost

These functions do not require any time setting; they are activated by a simple press on the touch buttons of the control panel.

Question 5

What replacement filters are recommended for the ROBLIN 6209269 - 6209265 hood?

Accepted Answer

Your ROBLIN 6209269 - 6209265 hood can be equipped with several types of filters depending on the exact model:

Grease filters (washable)

Washable aluminum filters. Clean them once a month in the dishwasher at maximum 50°C. Lifespan: 10 years.

Odor filters

Two options depending on your setup:

Washable odor filters: clean every 2 months in the dishwasher, then reactivate in the oven (10 min at 100°C max)
Activated carbon filters: replace every 3 months minimum depending on usage

CLEAN-R system (if equipped)

Ultraviolet lamps (lifespan: ~6000 hours, replace every 3 years approximately) and associated catalyst filters.

How to order spare parts

The manual states that no specific filter reference or price is provided in the documentation. To order the exact parts:

Note the serial number of your hood (visible on the nameplate inside)
Contact an authorized ROBLIN dealer or the manufacturer
Specify your exact model (6209269 or 6209265) and the desired filter type

Replacement parts are guaranteed to remain available for 10 years after the purchase of your appliance.

Question 6

How to change the bulb of the ROBLIN VIZIO FX MURALE hood?

Accepted Answer

To change the bulb of your ROBLIN VIZIO FX MURALE hood, follow these simple steps:

1. Safety first

Make sure the hood is unplugged or that the corresponding circuit breaker is turned off to avoid any risk of electrocution.

2. Access the bulb

Locate the diffuser or plastic cover that protects the bulb. Depending on the model, you may be able to remove it by sliding it or gently unscrewing it.

3. Remove the used bulb

Once the bulb is accessible, unscrew it counterclockwise if it is a screw type. If it is a bayonet bulb, push it slightly and then turn it to release it.

4. Install the new bulb

Insert the new bulb into the socket.
For a screw bulb, screw it in clockwise until it is securely fixed.
For a bayonet bulb, insert it and then turn it until it clicks into place.

5. Replace the diffuser

Replace the plastic cover or diffuser, ensuring it is securely fixed.

6. Restore power and test

Plug the hood back in or turn the circuit breaker back on, then turn on the hood to check that the bulb is working properly.

By following these steps, you can easily and safely replace the bulb of your ROBLIN VIZIO FX MURALE hood.

Question 7

How to reset the ROBLIN CONFIDENCE 1000 extractor hood?

Accepted Answer

To reset your ROBLIN CONFIDENCE 1000 extractor hood, the action depends on what you want to reset: the filter alarm or a general malfunction of the device.

Resetting the filter alarm (FG, FF or EF on the display): If the display shows FG, FF or EF, this indicates that the grease filters or charcoal filters need to be cleaned. To reset this alarm after cleaning the filters, press and hold the dedicated button for exactly 3 seconds. The display will temporarily switch to 24 with a blinking dot in the bottom right corner, then the alarm will clear. This reset is usually done when the motor is off.

Filter maintenance before resetting: The metal grease filters are washable and should be cleaned in the dishwasher at a maximum temperature of 50°C, about once a month or according to the indications displayed by the control. After cleaning, let them dry completely in the open air. These filters have a lifespan of 10 years. If your hood has active charcoal odor filters, they must be replaced every 3 months at a minimum or more often if the hood is used for more than 3 hours a day.

Complete reset in case of malfunction: If you encounter a general problem (the hood does not turn on, the controls do not respond, etc.), unplug the device from the electrical outlet for about 5 minutes, then plug it back in. This procedure resets the internal settings of the hood. Then turn on the hood to check that it is functioning normally.

If the alarm persists after cleaning the filters and resetting, or if the hood still does not work properly after unplugging, contact ROBLIN customer service at 04.88.78.59.93. Have the serial number of your hood handy, which is located on the nameplate inside the hood, behind the filters.

Question 8

How to reset the error code F6 on the ROBLIN CONFIDENCE 1000 hood?

Accepted Answer

The error code F6 on the ROBLIN CONFIDENCE 1000 hood generally indicates a temporary malfunction or a need to reset the device. To reset this error code, follow the steps below:

Steps to reset the error code F6:

Turn off the hood: Disconnect the hood from the power supply or turn off the corresponding circuit breaker.
Wait: Leave the device powered off for at least 5 minutes to allow a complete reset of the internal circuits.
Turn the hood back on: Reconnect it or turn the circuit breaker back on.
Check the display: Check if the error code F6 has disappeared. If the code persists, it may indicate a technical problem requiring specialized intervention.

If after this procedure the error code F6 remains displayed, it is advisable to contact a customer service or an authorized technician for a thorough diagnosis and possible repair.

Question 9

How to turn off the filter light on the ROBLIN BALTIC 900 hood?

Accepted Answer

To turn off the filter light on your ROBLIN BALTIC 900 hood, the procedure depends on the type of clogged filter. The hood has two distinct alarms that you need to reset after cleaning or replacing the filters.

For metal grease filters: Turn off the hood by pressing button A, then wait for the motor and lighting to completely stop. Clean the filters with soapy hot water or run them through the dishwasher if heavily soiled. Reinstall the filters correctly. Then press button C and hold it for about 2 seconds (the motor and lighting must be off). LED A blinks three times to confirm the reset of the grease filter saturation alarm, which naturally lights up after 100 hours of continuous operation.

For activated carbon filters: These filters cannot be washed or regenerated and must be replaced. Replace the carbon filter after removing it. Then press button B and hold it for about 2 seconds (the motor and lighting must be off). LED A blinks twice to deactivate the carbon filter alarm, which lights up after 200 hours of continuous operation.

Recommended maintenance frequencies: Clean the grease filters every 2 months of normal operation, or more often if you use your hood intensively. Replace the activated carbon filter approximately every 4 months, or more frequently depending on your usage. Never operate with a clogged filter, as this poses a fire risk and reduces suction efficiency.

If after these actions the alarm remains on, check that you have correctly reinstalled the filters. In case of persistent malfunction, contact ROBLIN customer service at 04 88 78 59 93.

Question 10

How to change the bulb of the ROBLIN STELLA 900 hood?

Accepted Answer

To change the bulb of your ROBLIN STELLA 900 hood, follow these simple and safe steps:

1. Safety first

Always unplug the hood from the electrical outlet before intervening to avoid any risk of electrocution.

2. Access the bulb

Locate the bulb(s) under the hood. Depending on the model, the bulb may be protected by a glass cover or a lid:

Gently remove this cover by unscrewing or unclipping it.

3. Remove the used bulb

Unscrew the used bulb counterclockwise.
If the bulb is broken, handle with care to avoid cuts.

4. Install the new bulb

Get a bulb compatible with the STELLA 900 model (check the recommended wattage and bulb type).
Twist the new bulb clockwise until it is securely fixed.

5. Replace the cover

Replace the cover or glass ensuring it is properly secured.

6. Check the operation

Plug the hood back in and turn it on to check that the bulb is working correctly.

By following these steps, you can easily and safely replace the bulb of your ROBLIN STELLA 900 hood.

User manual ROBLIN Range hood : user manuals and guides in PDF

Models ROBLIN Range hood most viewed

Other categories ROBLIN

Recent questions about Range hood ROBLIN