Question 1

How to start the SHARP R922STWE microwave oven?

Accepted Answer

Before first use, set the clock on your SHARP R922STWE oven. Press the CLOCK/TIMER button once, set the hours using the SELECT button, press this button again, set the minutes, and then press it one last time to start the clock. This step is important as the display will show the time at the end of each cooking session.

To start microwave cooking (the most common mode): open the door by pulling the handle, place your food directly on the glass turntable or in a suitable dish, then close the door. Press the MICROWAVE POWER button to choose your level (P100 for 100%, P80 for 80%, P50 for 50%, P30 for 30%, or P10 for 10%). As a guideline, use P100 for quick reheating (drinks, vegetables, ready meals), P80 for dense foods without cooking them too quickly, and P30 for defrosting. Turn the SELECT knob to enter the desired cooking time (up to a maximum of 95 minutes). Press START/+30 sec./ENTER to begin cooking. The display will show the countdown of the remaining time and the turntable will rotate automatically.

To use the grill or combined modes: press the GRILL/COMBINED button (once for grill only, or multiple times for combinations: C-1 for microwave + convection, C-2, C-3, or C-4 for other combinations). Select the cooking time with the SELECT button, then press START/+30 sec./ENTER. Important note: at half the grill cooking time, a beep will sound twice to remind you to turn the food.

For convection cooking: press the CONVECTION button to select the desired temperature (from 150°C to 240°C in 10°C increments). Preheating is recommended for best results. Press START/+30 sec./ENTER to confirm the temperature, then a double beep will indicate when the oven has reached the temperature and you can place the food inside. Enter the cooking time and press START/+30 sec./ENTER again.

During cooking: you can open the door to check your food. The timer will stop automatically. Close the door and press START/+30 sec./ENTER to resume. You can extend the time by 30 seconds at a time by pressing the same button during cooking. To temporarily stop the oven, use the STOP/CLEAR button. Press it twice to completely cancel the current program.

At the end of cooking, a beep will sound. The display will show the current time (if the clock has been set). Note: the interior light remains on for 10 minutes after the door is opened for safety reasons. Keep the door closed to remember this. Important: the door, the casing, and the inside of the oven become very hot during operation. Always use suitable thick kitchen gloves for handling.

Practical tip: you can also start cooking by directly pressing START/+30 sec./ENTER to cook for 30 seconds at maximum power (P100). Each additional press adds 30 seconds. This allows for quick reheating without programming.

Question 2

Why does my SHARP R752IN microwave seem less powerful than before?

Accepted Answer

Several factors may explain why your SHARP R752IN microwave seems less powerful:

1. Checking the power supply

Make sure the appliance is plugged into a properly powered outlet. A faulty outlet, inadequate extension cord, or voltage drop can reduce the effective power of the microwave.

2. Cleaning and maintenance

Food residues, grease, or dirt accumulated inside or on the door can affect cooking. Regularly clean the inside of the microwave and ensure that the door closes tightly.

3. Settings and cooking modes

Check that you are using the correct power level. Some specific programs or modes may operate at reduced power for delicate cooking.

4. Wear or technical failure

The magnetron, which generates the microwaves, may wear out over time and lose efficiency. Other internal components may also be involved. If you suspect a technical problem, a diagnosis by a professional is recommended.

5. Environmental conditions

Very low ambient temperatures can temporarily influence the performance of the microwave.

In summary, start by checking the power supply, cleaning, and settings. If the problem persists, it is advisable to have your appliance checked by a qualified technician.

Question 3

Why does my Sharp microwave continue to operate after displaying 'END' at the end of the cooking time?

Accepted Answer

When your Sharp microwave displays 'END' at the end of the cooking time, it normally means that cooking is finished. However, if the appliance continues to operate for several minutes after this display, several explanations are possible:

1. Keep Warm Function

Some Sharp microwave models have a keep warm function that can extend the operation of the appliance after cooking to keep food warm. Check if this option is activated and disable it if you do not want this feature.

2. Cooling or Ventilation Cycle

After cooking, the microwave may continue to run the fan or other components to cool down the appliance or the dish. This operation may last a few minutes but should not be prolonged beyond this time.

3. Technical Issue

If the microwave continues to heat or operate actively well after the 'END' display and beyond the normal cooling time, this may indicate a malfunction, such as a stuck relay or an electronic fault. In this case, it is recommended to have the appliance checked by a qualified professional.

What to do?

Check if the keep warm function is activated and disable it if necessary.
Observe if the prolonged operation corresponds to the cooling fan, which is normal.
If the microwave continues to heat or operate abnormally, unplug it and contact an authorized repair service.

User manual SHARP Microwaves : user manuals and guides in PDF

Models SHARP Microwaves most viewed

Other categories SHARP

Recent questions about Microwaves SHARP