Q: How to replace the bulbs of the SMEG SHB900SS hood?

The SMEG SHB900SS hood is equipped with 2 halogen 20W bulbs for lighting. Here’s how to replace them: Replacement Steps Remove the diffuser - Gently lift the clipped lamp cover from the bottom of the metal ring, supporting it with one hand Extract the bulb - Carefully pull the halogen bulb from its socket-shaped holder Install the new bulb - Insert the new 20W bulb, ensuring that both pins fit correctly into the holder's slots Replace the diffuser - Put the clipped lamp cover back in its original position Repeat this procedure for the second bulb if necessary. Refer to the LIGHT REPLACEMENT section on page 14 of the manual for detailed diagrams of the process.

Q: How to clean and maintain the filters of the KS905NXE2 hood?

The KS905NXE2 hood has two types of filters depending on its configuration: Metal grease filters Material: washable metal Recommended cleaning: at least once a month (more frequently with intensive use) Cleaning method: wash them with a neutral detergent, by hand or directly in the dishwasher Reassembly: ensure that the filter handle is facing outward Activated carbon filters (filtering version) Type: non-washable and non-regenerable Replacement: every 6 months minimum Indication: an alarm activates automatically after 200 hours of actual operation Installation: three possible systems depending on your model (90° rotating disc, cartridge with springs, or cartridge with threaded bracket) Important: the accumulation of grease in the filter panels not only compromises the performance of the hood, but it can also pose fire risks. Regular maintenance is therefore essential.

Q: How to set up the hood in recirculation mode (filtering)?

The SMEG KD150X-1 hood can operate in two modes: the extraction mode (venting air outside) and the filtering or recirculation mode (the air is purified and reintroduced into the kitchen). Installation steps in recirculation mode: Remove the standard grease filters present by default Install the activated charcoal filters following the diagrams in the manual (they replace the metal filters) Keep the motor inlet clear - do not install any external venting ducts The hood is now in filtering mode, ready to operate Important point: If your hood does not have activated charcoal filters, you must purchase them separately (they are not provided originally) before using recirculation mode. Maintenance in recirculation mode: Charcoal filters: To be replaced every 6 months minimum, or more often in case of intensive use. They are neither washable nor regenerable. Metal grease filters: If you keep them in another configuration, clean them once a month

Question 1

How to remove and replace the bulb of the hood?

Accepted Answer

To replace the bulb of your SMEG SHU921X extractor hood, follow these steps:

Turn off the power: Ensure that the hood is turned off and unplug it before any intervention.
Access the bulb: Depending on the model, you may need to remove the metal filters from the hood to access the lighting compartment. Some models allow for direct access.
Remove the old bulb: Once the bulb is visible, turn it counterclockwise or press lightly and then turn, depending on the type of base (screw or bayonet). Handle it with care.
Install the new bulb: Insert a replacement bulb of the same wattage and type (usually 40W or 60W bulbs depending on the model). Turn clockwise until fully tightened.
Test: Plug the device back in and turn it on to check that the lighting works correctly.

Tip: Refer to the instruction manual provided with your hood for the exact recommended bulb specifications, as the type and wattage may vary depending on your specific version of the SHU921X.

Question 2

How to replace the bulbs of the SMEG SHB900SS hood?

Accepted Answer

The SMEG SHB900SS hood is equipped with 2 halogen 20W bulbs for lighting. Here’s how to replace them:

Replacement Steps

Remove the diffuser - Gently lift the clipped lamp cover from the bottom of the metal ring, supporting it with one hand
Extract the bulb - Carefully pull the halogen bulb from its socket-shaped holder
Install the new bulb - Insert the new 20W bulb, ensuring that both pins fit correctly into the holder's slots
Replace the diffuser - Put the clipped lamp cover back in its original position

Repeat this procedure for the second bulb if necessary. Refer to the LIGHT REPLACEMENT section on page 14 of the manual for detailed diagrams of the process.

Question 3

How to clean and maintain the filters of the KS905NXE2 hood?

Accepted Answer

The KS905NXE2 hood has two types of filters depending on its configuration:

Metal grease filters

Material: washable metal
Recommended cleaning: at least once a month (more frequently with intensive use)
Cleaning method: wash them with a neutral detergent, by hand or directly in the dishwasher
Reassembly: ensure that the filter handle is facing outward

Activated carbon filters (filtering version)

Type: non-washable and non-regenerable
Replacement: every 6 months minimum
Indication: an alarm activates automatically after 200 hours of actual operation
Installation: three possible systems depending on your model (90° rotating disc, cartridge with springs, or cartridge with threaded bracket)

Important: the accumulation of grease in the filter panels not only compromises the performance of the hood, but it can also pose fire risks. Regular maintenance is therefore essential.

Question 4

How to set up the hood in recirculation mode (filtering)?

Accepted Answer

The SMEG KD150X-1 hood can operate in two modes: the extraction mode (venting air outside) and the filtering or recirculation mode (the air is purified and reintroduced into the kitchen).

Installation steps in recirculation mode:

Remove the standard grease filters present by default
Install the activated charcoal filters following the diagrams in the manual (they replace the metal filters)
Keep the motor inlet clear - do not install any external venting ducts
The hood is now in filtering mode, ready to operate

Important point: If your hood does not have activated charcoal filters, you must purchase them separately (they are not provided originally) before using recirculation mode.

Maintenance in recirculation mode:

Charcoal filters: To be replaced every 6 months minimum, or more often in case of intensive use. They are neither washable nor regenerable.
Metal grease filters: If you keep them in another configuration, clean them once a month

Question 5

Where to buy a compatible filter for the SMEG KD917X hood?

Accepted Answer

To purchase a compatible filter for your SMEG hood model KD917X, here are the main options:

Official SMEG website: The manufacturer's website often offers original spare parts, including filters suitable for each model.
Authorized dealers: Contact authorized SMEG dealers or service centers that can provide authentic filters for your hood.
Appliance stores: Some specialized stores or large retailers have universal or brand-specific filters for certain models.
Online sales sites: Platforms like Amazon, eBay, or other specialized sites may offer compatible filters. Be sure to check the exact reference to ensure compatibility with the KD917X model.

Make sure to choose a filter suitable for your hood to ensure proper filtration and optimal operation of the appliance.

Question 6

How to change the charcoal filter of the SMEG KD917X hood?

Accepted Answer

Your SMEG KD917X hood may be equipped with a KITFC900 charcoal filter (dimensions: 22 x 18 x 2 cm) to operate in recirculation mode. The charcoal filter does not necessarily need to be changed: it depends on the type of filter you have.

If you have a washable charcoal filter: Unplug the hood from the electrical circuit. Turn the two fastening buttons (g) located under the filter frame 90°. Carefully remove the charcoal foam pad (i) from its plastic housing (h). Clean the pad every two months with hot water and a suitable detergent, or place it directly in the dishwasher at 65°C without dishes. After washing, remove any excess water without damaging the filter, then place the pad in the oven for 10 minutes at 100°C to dry completely. Reassemble the pad in its frame and reinstall the whole unit by turning the buttons 90° until they click. Replace the pad every 3 years or if it is damaged.

If you have a traditional (non-washable) charcoal filter: This type of filter is neither washable nor regenerable and must be changed every 3 to 4 months depending on your usage frequency. Unplug the hood, then turn the two fastening buttons 90° to remove the filter frame. Install the new traditional filter by inserting it into its housing and closing the buttons.

Procedure for removing/replacing: Always start by unplugging the hood for safety reasons. Access the fastening buttons (g) located under the filter. Turn these two buttons 90° (a quarter turn) to release the filter frame. Pull the frame down and towards you to completely remove it. To replace the pad or install a new filter, perform the reverse operations ensuring that the buttons are fully pressed in after rotation.

Tip: On the KD917X hood, if a filter saturation indication system is present, trust this signal rather than a fixed schedule to determine the best time for cleaning or replacement. Note that the frame and mat of a traditional filter are welded together, so if you need to switch to this type of filter, do not attempt to use the plastic frame originally provided with your hood.

Question 7

Why does my SMEG KT90BL kettle heat up by itself and how can I resolve this issue?

Accepted Answer

If your SMEG KT90BL kettle heats up without you having turned it on, this indicates a malfunction that can be dangerous. Here are the steps to follow to identify and possibly resolve this issue:

1. Check the power button

Make sure that the on/off button is in the "off" position when you are not using it. Sometimes, a stuck or faulty button can cause unintended heating.

2. Check the cord and base

Examine the power cord for any signs of wear, cuts, or damage.
Check the base of the kettle to ensure it is not damaged or warped.

3. Unplug the device immediately

To avoid any risk of electric shock or fire, unplug the kettle as soon as you notice it heating up for no reason.

4. Test the kettle on another outlet

The problem may be with the electrical outlet itself. Try plugging the kettle into another outlet to see if the phenomenon persists.

5. Contact a professional

If after these checks the kettle continues to heat by itself, it is strongly recommended not to use it anymore and to contact customer service or an authorized repairer. This type of malfunction may be related to an internal defect requiring repair or replacement of the device.

User manual SMEG Range hood : user manuals and guides in PDF

Models SMEG Range hood most viewed

Other categories SMEG

Recent questions about Range hood SMEG