Q: How to adjust or align the doors of the SMEG FQ55FXDF refrigerator?

The SMEG FQ55FXDF model has a fixed door hinge . The manual for this model does not specify a specific adjustment procedure for the doors. If your doors are misaligned or do not close properly: Check the general alignment - Ensure that the refrigerator is level on a flat surface. A slight tilt towards the back (a few millimeters) is normal for the proper functioning of the doors. Clean the seals - Residue or debris on the seals can prevent proper closure. Clean them with a damp, soft cloth. Check the supports - Ensure that all adjustable feet of the refrigerator are in contact with the floor. Inspect the hinges - With fixed hinges, any adjustment requires technical intervention. If the door rubs or does not close properly despite cleaning the seals, contact the authorized SMEG service center. For any technical assistance specific to the FQ55FXDF model, please contact SMEG support directly, mentioning your model number.

Q: What should I do if the refrigerator is no longer cold after a power outage?

After a power outage, your SMEG C3170NE refrigerator has a compressor thermal protection device that automatically activates in the event of a sudden power cut. This is a normal and necessary safety system. Here’s what happens: The protection device "trips" during the power outage The appliance will automatically restart and resume normal operation after about 6 minutes If the cold has still not returned after 6 minutes: Check that the refrigerator is properly plugged in and powered Check that the thermostat is set to a position other than zero Ensure that the door seals are not damaged Check that air can circulate freely around the appliance (at least 10 cm of clearance) If the problem persists after these checks, contact SMEG customer service.

Q: Can I turn off only the freezer while keeping the refrigerator running on the SMEG SRA25X/2?

No, you cannot selectively turn off the freezer on the SMEG SRA25X/2 while keeping the refrigerator active. This model has a single thermostat (positions 1 to 6) located inside the refrigerator. The temperature control regulates both compartments together - there is no independent control to stop only the freezer. If your ice maker is leaking If your ice tray is leaking water, the recommended solution is: Check the positioning of the tray - make sure it is properly in place and not tilted Do not overfill the tray - fill it gradually to avoid overflow Check the condensation ducts - ensure they are not blocked Check the tilt of the refrigerator - the refrigerator should be slightly tilted backward for proper water drainage Temporarily empty the ice tray if you suspect it is causing the leak These adjustments should resolve the issue without needing to turn off the freezer. If the leak persists after these checks, it is recommended to contact a specialized technician.

Q: How do I set the temperature to the minimum on my SMEG CR325P1?

To set your SMEG CR325P1 to the lowest temperature: Open the refrigerator door Locate the numbered thermostat knob located inside (usually at the top right or left) Turn the knob to the lowest number (or 0) to achieve maximum cold Important points: The recommended setting for normal energy consumption is position 3-4 (approximately 4°C) The lowest position will produce intense cold - use it only if you need a very cold temperature Wait a few hours after adjusting to allow the appliance to stabilize its temperature before checking the result Always adjust towards higher numbers (1, 2, 3...) to decrease the intensity of the cold

Q: What does the tab (linguetta) on the SMEG ice tray mean?

The linguetta (or tab) is a small protrusion or peg located on the ice tray of the SMEG SRA25X/2. It plays an important role in inserting and securing the tray in place. Here’s how it works: Tray insertion - When you slide the tray towards the back of the freezer, the linguetta engages in a groove or slot designed for this purpose on the internal structure of the refrigerator. Position holding - Once the tray is fully pushed in, the linguetta allows you to feel that it is securely fixed. You will generally feel a small "click" or resistance indicating that the tray is correctly in place. Mechanism alignment - The linguetta ensures that the water supply system (the tube that fills the ice tray) is properly aligned with the tray. If the tray does not go all the way in: Try slightly rotating the internal drive mechanism (visible above the tray) a quarter turn, then reinsert the tray until you feel the "click" confirming correct insertion.

Q: How to correctly insert the ice tray into the SMEG SRA25X/2?

To correctly insert the ice tray of the SMEG SRA25X/2: Place the tray on one of the lower shelves of the freezer compartment Slide it back - Gradually push the tray towards the back of the freezer until you feel resistance Check the engagement - The small tab (linguetta) of the tray should engage in the designated groove. You should feel a slight "click" or resistance confirming that the water supply tube is properly aligned If insertion is difficult - Remove the tray, slightly turn the internal drive mechanism a quarter turn, then try again Maintenance tip: Before reinserting the tray, ensure it is not blocked by frost or solidified ice. Avoid using sharp tools to remove ice - this could damage the tray or the mechanism.

Q: Water is flowing in the freezer when I use the ice tray

This phenomenon is generally due to the ice tray in the freezer. Here are the points to check: Poorly positioned tray: Make sure that the ice tray is correctly inserted and securely fixed in the freezer compartment. If it is not properly secured, the water produced may flow beside the tray instead of filling the cells. Overflow during filling: If you pour water directly into the tray, fill it gradually. Overfilling will cause water to overflow into the freezer. Frost accumulation: Check that the tray is not blocked by frost or stuck ice cubes. Manual defrosting may be necessary (see the defrosting chapter in your manual). Tray location: On the SRA25X/2, the ice tray must be placed on a lower shelf of the freezer . Ensure that no item is blocking access or destabilizing the tray. If water continues to flow despite these checks, there may be a blockage in the freezer's drainage system or an assembly issue with the tray. Refer to the maintenance and defrosting section of your manual for detailed steps, or contact SMEG customer service if the problem persists.

Question 1

Where can I find a diagram or drawing of the back of the SMEG SBS8004PO refrigerator?

Accepted Answer

The PDF of this SMEG SBS8004PO manual does not contain a detailed diagram of the back of the appliance. However, here is what you can know about its physical structure:

Overall dimensions: 90.8 cm (width) × 182.5 cm (height) × 72 cm (depth)
The back houses the compressor, condenser, and refrigeration pipes necessary for cooling
Adjustable feet allow for stabilization on uneven floors

For a detailed view of the back, you can consult the official SMEG product sheet on the manufacturer's website, which usually provides detailed photos from all angles. The printed or PDF manual contains installation and connection diagrams, which specify the rear access points (water line, drainage, electrical supply).

Question 2

How to adjust or align the doors of the SMEG FQ55FXDF refrigerator?

Accepted Answer

The SMEG FQ55FXDF model has a fixed door hinge. The manual for this model does not specify a specific adjustment procedure for the doors.

If your doors are misaligned or do not close properly:

Check the general alignment - Ensure that the refrigerator is level on a flat surface. A slight tilt towards the back (a few millimeters) is normal for the proper functioning of the doors.
Clean the seals - Residue or debris on the seals can prevent proper closure. Clean them with a damp, soft cloth.
Check the supports - Ensure that all adjustable feet of the refrigerator are in contact with the floor.
Inspect the hinges - With fixed hinges, any adjustment requires technical intervention. If the door rubs or does not close properly despite cleaning the seals, contact the authorized SMEG service center.

For any technical assistance specific to the FQ55FXDF model, please contact SMEG support directly, mentioning your model number.

Question 3

What should I do if the refrigerator is no longer cold after a power outage?

Accepted Answer

After a power outage, your SMEG C3170NE refrigerator has a compressor thermal protection device that automatically activates in the event of a sudden power cut. This is a normal and necessary safety system.

Here’s what happens:

The protection device "trips" during the power outage
The appliance will automatically restart and resume normal operation after about 6 minutes

If the cold has still not returned after 6 minutes:

Check that the refrigerator is properly plugged in and powered
Check that the thermostat is set to a position other than zero
Ensure that the door seals are not damaged
Check that air can circulate freely around the appliance (at least 10 cm of clearance)

If the problem persists after these checks, contact SMEG customer service.

Question 4

Can I turn off only the freezer while keeping the refrigerator running on the SMEG SRA25X/2?

Accepted Answer

No, you cannot selectively turn off the freezer on the SMEG SRA25X/2 while keeping the refrigerator active.

This model has a single thermostat (positions 1 to 6) located inside the refrigerator. The temperature control regulates both compartments together - there is no independent control to stop only the freezer.

If your ice maker is leaking

If your ice tray is leaking water, the recommended solution is:

Check the positioning of the tray - make sure it is properly in place and not tilted
Do not overfill the tray - fill it gradually to avoid overflow
Check the condensation ducts - ensure they are not blocked
Check the tilt of the refrigerator - the refrigerator should be slightly tilted backward for proper water drainage
Temporarily empty the ice tray if you suspect it is causing the leak

These adjustments should resolve the issue without needing to turn off the freezer. If the leak persists after these checks, it is recommended to contact a specialized technician.

Question 5

How do I set the temperature to the minimum on my SMEG CR325P1?

Accepted Answer

To set your SMEG CR325P1 to the lowest temperature:

Open the refrigerator door
Locate the numbered thermostat knob located inside (usually at the top right or left)
Turn the knob to the lowest number (or 0) to achieve maximum cold

Important points:

The recommended setting for normal energy consumption is position 3-4 (approximately 4°C)
The lowest position will produce intense cold - use it only if you need a very cold temperature
Wait a few hours after adjusting to allow the appliance to stabilize its temperature before checking the result
Always adjust towards higher numbers (1, 2, 3...) to decrease the intensity of the cold

Question 6

Is the temperature adjustment manual for the SMEG CR325P1 in English or French?

Accepted Answer

The manual and instructions on the website are entirely in French. However, some physical labels on the thermostat knob of your appliance may display numbers or universal symbols (numbered from 0 to 6).

The main control is a numbered thermostat knob located inside the refrigerator, usually at the top right or left. This knob simply works by turning it to the numbers to adjust the cooling intensity:

Lower numbers (e.g., 0-1) = maximum cold
Position 3-4 = recommended setting (around 4°C)
Higher numbers (5-6) = less intense cold

If you see English text elsewhere on your appliance (for example, on branded parts), this is normal - manufacturers often produce for multiple markets. But the official manual provided here is in French to guide you.

Question 7

What does the tab (linguetta) on the SMEG ice tray mean?

Accepted Answer

The linguetta (or tab) is a small protrusion or peg located on the ice tray of the SMEG SRA25X/2. It plays an important role in inserting and securing the tray in place.

Here’s how it works:

Tray insertion - When you slide the tray towards the back of the freezer, the linguetta engages in a groove or slot designed for this purpose on the internal structure of the refrigerator.
Position holding - Once the tray is fully pushed in, the linguetta allows you to feel that it is securely fixed. You will generally feel a small "click" or resistance indicating that the tray is correctly in place.
Mechanism alignment - The linguetta ensures that the water supply system (the tube that fills the ice tray) is properly aligned with the tray.

If the tray does not go all the way in: Try slightly rotating the internal drive mechanism (visible above the tray) a quarter turn, then reinsert the tray until you feel the "click" confirming correct insertion.

Question 8

How to correctly insert the ice tray into the SMEG SRA25X/2?

Accepted Answer

To correctly insert the ice tray of the SMEG SRA25X/2:

Place the tray on one of the lower shelves of the freezer compartment
Slide it back - Gradually push the tray towards the back of the freezer until you feel resistance
Check the engagement - The small tab (linguetta) of the tray should engage in the designated groove. You should feel a slight "click" or resistance confirming that the water supply tube is properly aligned
If insertion is difficult - Remove the tray, slightly turn the internal drive mechanism a quarter turn, then try again

Maintenance tip: Before reinserting the tray, ensure it is not blocked by frost or solidified ice. Avoid using sharp tools to remove ice - this could damage the tray or the mechanism.

Question 9

Water is flowing in the freezer when I use the ice tray

Accepted Answer

This phenomenon is generally due to the ice tray in the freezer. Here are the points to check:

Poorly positioned tray: Make sure that the ice tray is correctly inserted and securely fixed in the freezer compartment. If it is not properly secured, the water produced may flow beside the tray instead of filling the cells.
Overflow during filling: If you pour water directly into the tray, fill it gradually. Overfilling will cause water to overflow into the freezer.
Frost accumulation: Check that the tray is not blocked by frost or stuck ice cubes. Manual defrosting may be necessary (see the defrosting chapter in your manual).
Tray location: On the SRA25X/2, the ice tray must be placed on a lower shelf of the freezer. Ensure that no item is blocking access or destabilizing the tray.

If water continues to flow despite these checks, there may be a blockage in the freezer's drainage system or an assembly issue with the tray. Refer to the maintenance and defrosting section of your manual for detailed steps, or contact SMEG customer service if the problem persists.

Question 10

Why is water leaking from the freezer and dripping underneath the refrigerator?

Accepted Answer

If water is leaking from the freezer compartment and escaping underneath your SMEG SRA25X/2 refrigerator, it may be due to several causes:

Possible causes and solutions:

Water accumulation during defrosting: The manual recommends placing towels to absorb melting water during manual defrosting. If you did not follow this step, water accumulates under the appliance. Perform a complete defrost by placing towels, then clean underneath.
Blocked drainage ducts: The condensation drainage passages may be blocked by frost, debris, or food. Check the back of the appliance to ensure the ventilation area remains clear, as indicated in the manual.
Poor appliance tilt: The refrigerator should be slightly tilted backward for water to flow properly towards the ducts. Check that your SMEG is not level.
Full defrost water tank: If your model has a condensation tray, it may be full or improperly positioned. Check the internal structure of the freezer.

Recommendations: Unplug the appliance before any intervention. Let it rest for a few hours to allow the system to return to normal temperature. Clean the inside of the freezer to remove any excess frost. If the problem persists after these checks, contact an authorized SMEG service center, as this may indicate a malfunction of the cooling system.

User manual SMEG Refrigerator : user manuals and guides in PDF

Models SMEG Refrigerator most viewed

Other categories SMEG

Recent questions about Refrigerator SMEG