Q: Why does the SMEG LSA6248B make a sound when starting the program?

Your SMEG LSA6248B dishwasher is designed to emit confirmation sounds when starting the wash cycle. This noise is normal and indicates that the program has been successfully registered. According to the manual, the dishwasher produces: A confirmation beep when starting or pausing the cycle A brief sound signal at the end of the wash program If the sound seems abnormal or is accompanied by another issue, check the manual display for possible error codes: E1 - Anti-overflow system intervention (Aquastop) E2 - Water safety level anomaly E3 - Water heating fault E4 - Water supply issue E5 - Water drainage anomaly E7 - Anomaly detected If an error code appears or if the noise persists abnormally, contact customer service .

Q: What is the purpose of the drain siphon on this dishwasher?

The drain siphon is an essential part of the drainage system of your SMEG STA6248 dishwasher. Its role is to allow wastewater to flow out properly after each wash cycle. On this model, the siphon can become clogged with food residues and deposits over time. If you notice that water is accumulating in the tub at the end of the cycle (error code E6 displayed), this indicates a "water drainage anomaly". How to check the siphon Check that the drain hose is not bent or crushed Ensure that the siphon is not clogged with residues Make sure that the filters are clean - clean them regularly under running water with a stiff brush, as the dishwasher cannot operate if the filters are clogged Also check that the end of the drain hose is positioned between 30 and 100 cm in height and is never covered by water If the problem persists after these checks, contact SMEG customer service.

Q: What are the dimensions and weight of the SMEG PL961.3?

The SMEG PL961.3 dishwasher has the following dimensions: Width : 597-599 mm Depth : 600 mm (freestanding version) or 590 mm (semi-integrated version) Height : 850-870 mm (freestanding version) or 820-870 mm (semi-integrated version) Weight : approximately 45 kg Capacity : 12 place settings Dimension variations depend on your model: freestanding version (independent installation) or semi-integrated (partial installation in a cabinet).

Q: How to properly install the telescopic rails of the SMEG STA6245-9 dishwasher?

The telescopic rails are sliding guide rails that allow you to move the upper or lower basket grids of the SMEG STA6245-9 forward or backward for easier access during loading and unloading. Correct installation of the rails The installation must follow a specific order to avoid the rail getting stuck: Step 1: Engage the rear hook - First, insert the hook located at the back of the telescopic rail onto the fixed rail of the basket (intermediate length rail). Step 2: Lock the front hook - Once the rear hook is correctly in place, position and then lock the front hook of the rail by pressing it firmly until it clicks. If the rail gets stuck If you encounter resistance when inserting, it usually means that the rear hook is not properly engaged on the intermediate rail. Do not force it - remove the rail and start again, ensuring to align the rear hook first. Once the rear hook is well positioned, installing the front hook will be effortless. Repeat this operation for both rails (right and left) so that your grids slide freely.

Question 1

What does the red light with a wavy line symbol mean on my SMEG DWAFI315T dishwasher?

Accepted Answer

section in your manual to optimize the dosage according to your local water.

Once the reservoir is filled and the dosage adjusted, the light should go off after the next wash cycle.

Tip: rinse aid significantly improves drying and reduces spots on dishes. Its use is recommended even if your detergent indicates "all-in-one".

Question 2

Why does the SMEG LSA6248B make a sound when starting the program?

Accepted Answer

Your SMEG LSA6248B dishwasher is designed to emit confirmation sounds when starting the wash cycle. This noise is normal and indicates that the program has been successfully registered.

According to the manual, the dishwasher produces:

A confirmation beep when starting or pausing the cycle
A brief sound signal at the end of the wash program

If the sound seems abnormal or is accompanied by another issue, check the manual display for possible error codes:

E1 - Anti-overflow system intervention (Aquastop)
E2 - Water safety level anomaly
E3 - Water heating fault
E4 - Water supply issue
E5 - Water drainage anomaly
E7 - Anomaly detected

If an error code appears or if the noise persists abnormally, contact customer service.

Question 3

How to reset or cancel an alarm on my SMEG LVS1251X1 dishwasher?

Accepted Answer

If your SMEG LVS1251X1 dishwasher displays an alarm or error code, there is a simple reset procedure.

First method: open and close the door

Open the appliance door, wait a few seconds, then close it again. This is usually enough to cancel a temporary alarm.

Second method: turn the machine off and on

Press the ON/OFF button to completely turn off the appliance. Wait about 10 seconds, then press ON/OFF again to restart it.

After this reset, your machine will resume normal operation and the alarm will disappear.

If the alarm persists after these two actions, consult the error code table in the manual (accessible via the PDF viewer on this page) to identify the specific type of anomaly and take appropriate measures.

Question 4

Why doesn't the wash cycle start on my SMEG LVS1251X1 dishwasher?

Accepted Answer

If the wash cycle does not start on your SMEG LVS1251X1 dishwasher, first check these essential points:

Is the water supply tap open? Make sure that the main water supply tap is fully open. This is often the first cause of a cycle not starting.
Is a program selected? Use the program selection button to choose one of the 5 available cycles: Soaking, Light, Bio (50°C), Normal (65°C), or Ultra Clean (70°C).
Has the Start/Pause button been pressed? After selecting your program, you must press the Start/Pause button to start the cycle. The indicator lights on the dashboard will light up to confirm the start.
Is there regenerating salt? If the salt level indicator is active (light on), fill the compartment with regenerating salt. A lack of salt can sometimes prevent the start.
Is there detergent? Make sure that the detergent compartment is not empty. You can use 3-in-1 combined products or regular detergent.

If after checking these items the cycle still refuses to start, consult the troubleshooting section of your manual or contact SMEG customer service.

Question 5

How to stop or cancel a running program on the SMEG STA643DD?

Accepted Answer

To stop a running program on your SMEG STA643DD dishwasher, press and hold the start/pause button for about 3 seconds. The program will be canceled immediately and the appliance will return to the standby state.

If after canceling the program the appliance does not return to normal operation, you can reset the system by unplugging the appliance for 1 minute, then plugging it back in. This will completely reset the electronics of the dishwasher.

Question 6

What is the purpose of the drain siphon on this dishwasher?

Accepted Answer

The drain siphon is an essential part of the drainage system of your SMEG STA6248 dishwasher. Its role is to allow wastewater to flow out properly after each wash cycle.

On this model, the siphon can become clogged with food residues and deposits over time. If you notice that water is accumulating in the tub at the end of the cycle (error code E6 displayed), this indicates a "water drainage anomaly".

How to check the siphon

Check that the drain hose is not bent or crushed
Ensure that the siphon is not clogged with residues
Make sure that the filters are clean - clean them regularly under running water with a stiff brush, as the dishwasher cannot operate if the filters are clogged
Also check that the end of the drain hose is positioned between 30 and 100 cm in height and is never covered by water

If the problem persists after these checks, contact SMEG customer service.

Question 7

What are the dimensions and weight of the SMEG PL961.3?

Accepted Answer

The SMEG PL961.3 dishwasher has the following dimensions:

Width: 597-599 mm
Depth: 600 mm (freestanding version) or 590 mm (semi-integrated version)
Height: 850-870 mm (freestanding version) or 820-870 mm (semi-integrated version)
Weight: approximately 45 kg
Capacity: 12 place settings

Dimension variations depend on your model: freestanding version (independent installation) or semi-integrated (partial installation in a cabinet).

Question 8

How to remove and reinstall the orbital washing arm of the SMEG STL22124?

Accepted Answer

Removing the orbital arm

To remove the orbital washing arm, grasp the longest arm and lift it upwards. It will easily unlock and can be completely removed.

Cleaning and reinstalling

After removal, wash the arm under running water to remove any buildup of residues or limescale in the openings. Carefully reinsert it into its housing ensuring it clicks into place.

Checking proper operation

After reinstallation, check that the arm rotates freely by turning it manually. If the rotation is difficult or blocked:

Check that it has been correctly mounted in its housing
Ensure that the water outlet openings are not blocked
Make sure nothing is obstructing its rotation

For any replacement parts, the manual does not provide a specific reference number. Please contact an authorized SMEG service center.

Question 9

How to properly install the telescopic rails of the SMEG STA6245-9 dishwasher?

Accepted Answer

The telescopic rails are sliding guide rails that allow you to move the upper or lower basket grids of the SMEG STA6245-9 forward or backward for easier access during loading and unloading.

Correct installation of the rails

The installation must follow a specific order to avoid the rail getting stuck:

Step 1: Engage the rear hook - First, insert the hook located at the back of the telescopic rail onto the fixed rail of the basket (intermediate length rail).
Step 2: Lock the front hook - Once the rear hook is correctly in place, position and then lock the front hook of the rail by pressing it firmly until it clicks.

If the rail gets stuck

If you encounter resistance when inserting, it usually means that the rear hook is not properly engaged on the intermediate rail. Do not force it - remove the rail and start again, ensuring to align the rear hook first. Once the rear hook is well positioned, installing the front hook will be effortless.

Repeat this operation for both rails (right and left) so that your grids slide freely.

Question 10

Is a thermal insulation plate required under the countertop for the SMEG STA6245-9?

Accepted Answer

No, you do not need to place a plate under the countertop if your dishwasher is normally built-in. The thermal insulation plate is only required if the dishwasher is installed near a heat source (notably a cooking hob).

According to the SMEG STA6245-9 manual: "If the dishwasher is installed near a heat source, a thermal insulation panel must be placed to prevent overheating and breakdowns."

Important: It is absolutely forbidden to install this dishwasher under a ceramic glass cooking hob. However, installation is possible under a traditional cooking hob if the countertop is continuous and the appliance is properly secured - in this specific case, thermal protection becomes essential.

For standard installation under a regular (non-heating) countertop, no additional plate is necessary. Just ensure that the hole for the pipes and cable has a minimum diameter of 8 cm, and that the appliance is well screwed to the adjacent furniture for stability.

User manual SMEG Dishwasher : user manuals and guides in PDF

Models SMEG Dishwasher most viewed

Other categories SMEG

Recent questions about Dishwasher SMEG