Q: What does error code F4 mean on the BRANDT BPI 164 HUX induction cooktop and how can it be resolved?

The error code F4 on the BRANDT BPI 164 HUX induction cooktop indicates that a temperature sensor (NTC probe) of the rear burner is malfunctioning. This sensor continuously monitors the temperature of the bottom of the cookware to ensure safe cooking. When this sensor has a connection fault or an open circuit, the device displays the F4 code to alert you of the malfunction. Before concluding that the sensor is defective, you can perform a few simple checks. Start by allowing the cooktop to cool down completely if it has been used intensively, then press any button to see if the error disappears. Sometimes, a restart is enough to reset the system. Also, check that the grates and ventilation openings are not blocked . Poor air circulation can cause overheating, triggering thermal safety mechanisms. Ensure that air circulates properly between the front and back of your cooktop, especially if it is installed above an oven or drawer. If necessary, improve ventilation by creating a small side opening (approximately 8 cm x 5 cm) in the cabinet. If the F4 code persists after these checks, it indicates an electronic issue requiring professional intervention . The temperature sensor may be defective or there may be a break in the internal electrical circuit. This repair cannot be resolved by the user and requires the replacement of the probe by a qualified technician. We recommend contacting BRANDT customer service at 09 69 39 25 25 (Monday to Saturday, 8 AM to 8 PM) or reaching out to an authorized BRANDT service technician. Have the service reference of your device (available on the nameplate attached under the cooktop) ready to facilitate the handling of your request.

Question 1

What are the installation dimensions for the BRANDT TI618BT1 cooktop?

Accepted Answer

For the BRANDT TI618BT1 cooktop, the recommended installation dimensions are as follows:

Width: 56 cm
Depth: 49 cm

These dimensions correspond to the space needed in your countertop to properly install the cooktop. It is important to accurately measure the existing opening to ensure a proper installation and avoid any issues during replacement.

Also, be sure to follow the manufacturer's recommendations regarding clearances around the appliance to ensure adequate ventilation and safe use.

Question 2

What does error code F4 mean on the BRANDT BPI 164 HUX induction cooktop and how can it be resolved?

Accepted Answer

The error code F4 on the BRANDT BPI 164 HUX induction cooktop indicates that a temperature sensor (NTC probe) of the rear burner is malfunctioning. This sensor continuously monitors the temperature of the bottom of the cookware to ensure safe cooking. When this sensor has a connection fault or an open circuit, the device displays the F4 code to alert you of the malfunction.

Before concluding that the sensor is defective, you can perform a few simple checks. Start by allowing the cooktop to cool down completely if it has been used intensively, then press any button to see if the error disappears. Sometimes, a restart is enough to reset the system.

Also, check that the grates and ventilation openings are not blocked. Poor air circulation can cause overheating, triggering thermal safety mechanisms. Ensure that air circulates properly between the front and back of your cooktop, especially if it is installed above an oven or drawer. If necessary, improve ventilation by creating a small side opening (approximately 8 cm x 5 cm) in the cabinet.

If the F4 code persists after these checks, it indicates an electronic issue requiring professional intervention. The temperature sensor may be defective or there may be a break in the internal electrical circuit. This repair cannot be resolved by the user and requires the replacement of the probe by a qualified technician.

We recommend contacting BRANDT customer service at 09 69 39 25 25 (Monday to Saturday, 8 AM to 8 PM) or reaching out to an authorized BRANDT service technician. Have the service reference of your device (available on the nameplate attached under the cooktop) ready to facilitate the handling of your request.

Question 3

Why is the temperature flashing on my BRANDT BPI1631UB induction cooktop and why is it not heating anymore?

Accepted Answer

The flashing temperature on your BRANDT BPI1631UB induction cooktop is an alert signal indicating a detection or safety issue preventing cooking. Here are the main causes and specific solutions for your model.

First, check the compatibility and size of the cookware: if the base of your pot or pan is too small, the power indicator will flash and the burner will not operate, even if the material is suitable for induction. Ensure that the diameter of the cookware meets the minimum requirement for your burner (refer to the power table in the manual). Also, check that you are using cookware made of compatible materials: magnetic stainless steel, cast iron. Glass, aluminum without a special base, copper, and some non-magnetic stainless steels will not work.

Check the error code displayed: if a code appears with the flashing, it indicates the specific cause. Code F7 means that the electronic circuits have overheated (your cooktop lacks ventilation - increase the airflow in the cabinet). Code F9 indicates insufficient electrical voltage (below 170 V) - check your electrical installation. Code F0 indicates a temperature that is too low (below 5°C) - wait for the cooktop to warm up.

Check the overheat protection: each cooking zone has a sensor that monitors the temperature of the cookware. If you left an empty pot on an active burner, the cooktop automatically reduced its power to protect itself. Allow it to cool down, empty the burners completely, and then try again.

Check the display and controls: during normal operation, the keyboard indicators always flash, which is a functioning indicator. However, if you have a spill that has covered the control buttons, the cooktop will automatically stop. Clean or remove the object, then restart cooking. If the child safety lock is activated, the cooktop will not operate - press the lock button to unlock it.

Reset procedure: completely unplug the cooktop for 5 minutes, then plug it back in. This resets the electronic system and may resolve temporary blockages.

If after these checks the temperature continues to flash and the cooktop still does not heat, or if an error code persists (notably F7), contact BRANDT Customer Service as there may be an electronic malfunction or a ventilation issue in the cabinet that requires technical intervention.

User manual BRANDT Hob : user manuals and guides in PDF

Models BRANDT Hob most viewed

Other categories BRANDT

Recent questions about Hob BRANDT