Question 1

How do I adjust the water level on the MAYTAG MVW5035MW?

Accepted Answer

The MAYTAG MVW5035MW washing machine features an automatic water level detection system. This system automatically adjusts the filling based on the amount of laundry detected, without requiring any manual adjustment on your part.

The appliance automatically fills the drum to the appropriate level for each selected cycle. The only exception is the cleaning cycle with affresh®: it fills the machine to a level higher than that of normal washing programs, in order to optimize deep cleaning.

Therefore, you do not have a button or setting to adjust the water level - the machine manages this automatically for you.

Question 2

How do I remove the agitator from the Maytag Bravos X MVWX700XL washing machine?

Accepted Answer

Your Maytag Bravos X MVWX700XL washing machine is equipped with a washplate system, not a traditional agitator. Unlike conventional washers, this high-efficiency model uses a rotating plate at the center of the drum to move clothes and apply detergent directly to stains.

There is no agitator to remove on this model. The washing system relies on the central washplate, which must remain in place. This plate cannot and should not be removed during normal operation of the machine.

If you encounter operational issues or if an object is stuck under the plate, here’s what you can do:

Unplug the machine from the electrical outlet
Open the lid and remove all clothing
Visually inspect around the washplate to check for any stuck objects (coins, buttons, small items)
If an object is stuck between the drum and the tub, you will need to contact Maytag service, as this requires disassembling internal components

For regular maintenance, refer to the "Cleaning your washer" section of the manual: run the Clean Washer with AFFRESH cycle every 30 washes to keep the interior clean and fresh. Remember to empty pockets before each wash to prevent small items from getting stuck in the washplate area.

Question 3

Why doesn't the drum of my MAYTAG Bravos X MVWX700XL washing machine spin completely and how can I resolve this issue?

Accepted Answer

If the drum of your MAYTAG Bravos X MVWX700XL washing machine is not spinning completely, several causes may be responsible. Here are the main areas to check and possible solutions:

1. Check the laundry load

An overloaded laundry load can block the drum. Make sure not to exceed the recommended capacity of your machine. Remove some laundry and restart a cycle to see if the drum spins normally.

2. Check the lid closure

The drum may not spin properly if the lid is not securely closed. Ensure that the door is locked before starting the machine.

3. Listen for unusual noises

Abnormal noises may indicate a mechanical problem, such as a defective motor or a worn belt. Pay attention to the sounds during startup and operation.

4. Inspect the drive belt

The belt that spins the drum may be broken or loose. If you are comfortable handling it, you can check its condition by opening the back panel of the machine. Otherwise, call a professional.

5. Check the condition of the bearings

If the drum is difficult to turn by hand or makes a grinding noise, the bearings may be worn or damaged. This often requires repair or replacement by a technician.

6. Perform a machine reset

Unplug the machine for about 5 minutes, then plug it back in. Sometimes, a simple restart can resolve temporary electronic malfunctions.

If the problem persists after these checks, it is recommended to contact an authorized repair service for a thorough diagnosis and appropriate intervention.

Question 4

Why is the agitator of my MAYTAG Bravos X MVWX700XL washing machine not working during the spin cycle while the motor is running?

Accepted Answer

If your MAYTAG Bravos X MVWX700XL washing machine drains water properly but the agitator does not turn during the spin cycle while the motor is running, several causes may explain this malfunction:

1. Check the laundry load

An overloaded laundry load can prevent the agitator from turning freely. Be sure not to exceed the recommended capacity of your machine.

2. Check the wash cycle

Ensure that the selected cycle includes both the spin and the operation of the agitator. Some specific cycles may disable the agitator.

3. Lid safety switch

The machine is equipped with a safety device that blocks the agitator if the lid is not properly closed. Check that the lid is securely latched.

4. Belt or transmission issue

If your model uses a belt to drive the agitator, it may be worn, loose, or broken, preventing the agitator from turning despite the motor running. A visual inspection or check by a professional is recommended.

5. Mechanical or motor malfunction

An internal problem with the motor or transmission system may also be the cause. If you hear the motor running without the agitator moving, this may indicate a mechanical defect requiring repair.

6. Resetting the machine

Sometimes, a simple restart can resolve electronic issues. Unplug the machine for a few minutes and then plug it back in to attempt a reset.

If after these checks the agitator still does not work, it is advisable to call a qualified technician to diagnose and repair the problem.

Question 5

Does the Maytag Bravos X MVWX700XL1 model have a lint filter?

Accepted Answer

The Maytag Bravos X MVWX700XL1 model does not have a traditional lint filter like some other washing machines. This model uses a non-agitator washing system, which reduces the need for a separate filter.

However, it is important to regularly check the inside of the drum as well as the drain pump area to ensure that no debris or lint accumulates, which could affect the proper functioning of the machine.

Question 6

Where is the filter of the MAYTAG Bravos X MVWX700XL washing machine and how do I clean it?

Accepted Answer

The filter of the MAYTAG Bravos X MVWX700XL washing machine is an important component to maintain regularly to ensure the proper functioning of your appliance. Here’s how to locate and clean it:

Locating the filter

The filter may be located inside the drum, often behind a small panel or cover situated in the drum.
On some models, it may also be accessible at the back of the machine, near the drain pump.

Steps to clean the filter

Unplug the machine to ensure your safety before any intervention.
Open the drum and look for a small cover or panel that protects the filter.
Gently remove the filter once located.
Clean the filter under a stream of warm water to remove lint, residues, and accumulated dirt.
Replace the filter correctly and ensure it is securely fastened.
Plug the machine back in and check that everything is working normally.

Regular maintenance of the filter helps prevent bad odors, clogs, and improves the efficiency of your washing machine.

User manual MAYTAG Washing machine : user manuals and guides in PDF

Models MAYTAG Washing machine most viewed

Other categories MAYTAG

Recent questions about Washing machine MAYTAG