Question 1

How to turn on the SABA SB32HDS19 television without a remote control?

Accepted Answer

You can turn on your SABA SB32HDS19 without a remote control by using the control button located on the side of the television.

To turn on the television from standby mode:

Locate the central button on the side of the TV case
Press the central button once to turn on the device

Once the television is on, you can control basic functions with this same control button:

Volume: press the up or down buttons to increase or decrease the volume
Channels: press the central button once to display the information bar with the current channel number, then use the up/down buttons to change channels
Sources: press the central button twice to display the list of available input sources (HDMI, USB, etc.), then navigate with the up/down buttons
Standby: press and hold the central button for a few seconds to turn off the television and put it in standby mode

The control button is your main control in the absence of a remote control. It provides full access to the essential functions of the SABA SB32HDS19: power on, volume, channel change, and input selection.

Question 2

How to find the IP address of the SABA SB32HDS19 television

Accepted Answer

The IP address of your SABA SB32HDS19 television can be easily found through the built-in menu. Here’s how to access it:

Press the remote control to open the main menu
Navigate to Settings
Go to System
Select Network
Access Advanced Settings to view the IP address, gateway, and DNS servers

Your SABA SB32HDS19 TV has an RJ45 Ethernet connection on the back panel and Wi-Fi 802.11 a/b/g/n, allowing you to set up a manual connection or use the WPS button for quick pairing with your router. You can also test your internet speed directly through the TV's built-in diagnostic.

Question 3

How to reset or recover the lock PIN code of the SABA LED26V11 television?

Accepted Answer

If you have forgotten the lock PIN code of your SABA LED26V11 television, here are some steps to follow to try to reset or recover it:

1. Try the default PIN codes

Many televisions use standard default PIN codes. Try entering the following codes:

0000
1234
1111

2. Reset the television

Unplug the television from the power outlet for about 5 to 10 minutes, then plug it back in. Sometimes, this can reset certain temporary settings, including the lock.

3. Use a factory reset procedure

If the default codes do not work, it is possible to reset the television to factory settings, which will remove the PIN code. The procedure varies by model, but generally:

Turn off the television.
Press certain buttons simultaneously (for example, volume + and power button) for a few seconds.
Follow the on-screen instructions to reset the device.

Warning: this operation will erase all custom settings.

4. Contact SABA customer service

If none of the previous solutions work, contact SABA customer service. They can provide you with a master code or specific assistance for your model.

By following these steps, you should be able to unlock your television or reset the PIN code.

Question 4

What is the programming code for the remote control for the SABA SCB1910VX television?

Accepted Answer

To program a universal remote control with your SABA SCB1910VX television, you need to use a specific programming code. The most common codes for SABA televisions are: 0625, 3434, 0650, 0714, 1588, 2676 (4-digit codes). You can also try the 3-digit codes: 551, 102, 190, 136, 114, 223, 225 or the 5-digit codes: 13656, 19740, 19930. These codes are compatible with OneForAll and Philips universal remotes.

To program your universal remote, follow this procedure: Turn on the SABA SCB1910VX television. Press the SET or PROG button on your universal remote until the indicator light turns on or blinks (depending on your remote model). Some remotes require a long press of 3 to 5 seconds. Enter one of the SABA codes provided above using the numeric keys. The code must be entered correctly, digit by digit. Check that the indicator light turns off or blinks once to confirm that the code has been accepted. If the light stays on continuously or turns off immediately, the code is not correct.

Once programming is complete, test all the main functions of your remote: increase/decrease the volume by pressing the V+ and V- buttons, change channels with the P+ and P- buttons, turn the television on and off with the Power button. If one or more functions do not respond, it means that the code is not fully compatible. In this case, repeat the procedure with another SABA code.

If none of the provided codes work, you can use the automatic search function available on some universal remotes. To do this, press SET or PROG until the indicator light turns on, then enter 9-9-1. Then hold down the POWER button and repeatedly press the P+ button (next channel) until the television turns off. The correct code will have been found automatically. You then need to press SET or POWER to store this code.

Important note: These universal codes work with most brands of universal remotes (OneForAll, Philips, Logitech, etc.), but depending on your remote model, the steps may vary slightly. Refer to the user manual of your universal remote for the exact procedure, including the button to activate programming (SET, PROG, SETUP, etc.) and the numeric keys to use. If you have the paper manual for the SABA SCB1910VX television, the appropriate code for your region is likely indicated in the settings or installation chapter.

User manual SABA Television : user manuals and guides in PDF

Models SABA Television most viewed

Other categories SABA

Recent questions about Television SABA