IAN 66760 - Lamp Livarno Lux - Free user manual and instructions

Product Type	Halogen Recessed Spotlights (Set of 6)
Model Number	6729
Brand	Livarno Lux
IAN	66760
Operating Voltage	230–240 V ~ 50 Hz
Power Consumption	6 x 50 W (max 300 W total)
Bulb Type	GU10, 230–240 V, 50 W max
Number of Bulbs	6 (pre-installed)
Bulb Diameter	85 mm
Installation Opening	68 mm diameter
Protection Class	II (double insulation)
Minimum Cable Cross-Section	2 x 0.75 mm²
Minimum Distance Between Spots	20 cm
Minimum Clearance Above/Sides	10 cm
Proper Use	Indoor, dry, enclosed spaces only
Included Items	6 spotlights with bulbs, 6 mains sockets, 12 retaining springs, 1 instruction manual
Guarantee	36 months from date of purchase
Max Temperature in Installation Area	90 °C
Cleaning	Dry, lint-free cloth only; no water or solvents
Disposal	Separate collection for electrical/electronic equipment (WEEE)

Frequently Asked Questions - IAN 66760 Livarno Lux

How do I install the Livarno Lux IAN 66760 recessed spotlights?

Installation must be done by a qualified electrician. First, mark positions and drill 68 mm holes (min 20 cm apart). Guide the power line through the opening, connect to the terminal block (L/N), and secure with cable holder. Attach retaining springs, insert the spotlight into the opening, and unfold springs to fix. Finally, switch on power.

What type of bulbs does the IAN 66760 use and how do I replace them?

Use 230–240 V GU10 bulbs with max 50 W. To replace, disconnect power and let lamp cool. Remove the spring washer, pull out the socket, turn the bulb ¼ turn anticlockwise to remove. Insert new bulb and turn clockwise ¼ turn, then secure with spring washer.

What is the correct voltage and power for this lamp?

The operating voltage is 230–240 V ~ 50 Hz. Total power consumption is 6 x 50 W (300 W). The bulb type is GU10 with a maximum wattage of 50 W each.

Can I install this lamp in a bathroom or outdoors?

No. This lamp is suitable only for indoor use in dry, enclosed spaces. Do not install in bathrooms or areas with moisture, as it is not water-resistant.

What safety precautions should I take before installation?

Always disconnect the mains supply (remove fuse or switch off circuit breaker). Use a voltage tester to confirm no power. Ensure the lamp is not damaged and that the mains voltage matches the required 230–240 V.

How do I clean the recessed spotlights?

First, disconnect the lamp from the mains and let it cool. Clean only with a dry, lint-free cloth. Never use water, solvents, or immerse the lamp in liquid.

What is the minimum distance between two spotlights?

The distance between two installation spotlights must be at least 20 cm. Also, maintain a clearance of at least 10 cm above and to the sides of each fitting.

What should I do if a bulb breaks or is damaged?

Immediately replace any faulty bulb. Do not install if bulb or lampshade is damaged. Use only 230–240 V GU10 bulbs of max 50 W. Handle with a clean cloth to avoid oil residue.

Is the Livarno Lux IAN 66760 covered by a warranty?

Yes, it comes with a 36-month warranty from the date of purchase. Warranty covers material and manufacturing defects but not wear parts like bulbs or damage from improper use.

How should I dispose of the lamp at the end of its life?

Do not dispose with household waste. The product must be collected separately for electrical and electronic equipment (WEEE). Take it to a recycling collection point to reduce environmental impact.

USER MANUAL IAN 66760 Livarno Lux

HALOGEN RECESSED SPOTLIGHTS

Interior ceiling with recessed lighting fixtures and a window frame (no text or symbols visible)

GB IE

HALOGEN RECESSED SPOTLIGHTS

Operation and Safety Notes

SE

INFÄLLDA

HALOGENLAMPOR, SET

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

FI

GB/IE Operation and Safety Notes Page 5

Simple line drawing of a biological structure with a curved arrow and label 'C' (no text or symbols on the diagram itself)

Diagram of a mechanical setup with a central component and two crossed arms, surrounded by particles (no text or symbols)

Introduction

Proper use....Page 6

Included items Page 6

Description of Parts Page 6

Technical Data Page 6

Safety

Safety advice......Page 6

Preparation

Required tools and materials......Page 7

Before installation......Page 8

Preparations for use

Installation Page 8

Changing the bulbs....Page 8

Maintenance and Cleaning Page 9

Disposal Page 9

Information

Guarantee Page 9

Service Page 9

Declaration of Conformity....Page 9

Halogen Recessed Lights

- Introduction

Please read carefully and completely through these operating instructions. Fold out both pages with the illustrations.

These instructions form part of the product and contain important information about bringing the product into use and its handling. Always observe all the safety advice. Check that the correct mains voltage is available and that all the parts have been properly assembled before bringing into use. Should you have any questions or be uncertain as to how to operate the device, please get in touch with your dealer or service point. Please keep these instructions in a safe place and hand them on to a third party if necessary.

- Proper use

This light is suitable only for interior use, in dry and enclosed spaces. This lamp is intended for use only in a domestic environment. The light can be fitted to all normally inflammable surfaces.

- Included items

Check that all the items and accessories are present and that the lamp is in perfect condition immediately after unpacking.

6 Installation spotlights with pre-installed bulbs

6 Mains sockets

12 Retaining springs

1 Operating instructions

● Description of Parts

1 Lamp housing
2 Bulb
3 Spring ring
4 Retaining spring

5 Cover
6 Terminal block
7 Cable holder
8 Mains socket
9 Fitting

- Technical Data

Model no.: 6729

Operating voltage: 230–240V \~, 50 Hz

Bulbs: 230-240V, GU10, 50W

Power consumption: 6 x 50 W

Dimensions of

each bulb: ∅ 85 mm

Installation opening: ∅ 68 mm

Protection class: II/

For the cable harness (not supplied) a minimum cross-section of 2 × 0.75 mm^2 is to be used. The corresponding cable is to be provided with wire end ferrules.

● Safety

Safety advice

The right to claim under the guarantee shall be rendered invalid in respect of damage caused by the non-observance of these operating instructions! No liability is accepted for consequent damage! No liability is accepted for damage to property or persons caused by improper handling or non-observance of the safety advice!

To avoid danger to life from electric shock

■ Ensure that a qualified electrician or a person trained to carry out electrical installations performs the electrical installation.
■ Every time before connecting the lamp the mains, check it and the mains lead for damage. Never use your light if you find it is damaged in any way.

CAUTION! A damaged mains lead presents a serious danger to life from electric shock. In the event of damage, repairs or other problems with the lamp please contact the service centre or an electrician.

Before installation, remove the fuse for this circuit or switch off at the circuit breaker (0 setting) in the fuse box.
Before assembly, ensure that the mains voltage available corresponds to the operating voltage necessary of the light (230–240 V\~).
■ Never let the lamp come into contact with water or other liquids.
■ Never open or insert anything into electrical fittings or equipment. Doing this sort of thing can lead to a serious danger to life from electric shock.
- Do not install the lamp on damp or conducting surfaces.

To avoid danger of fire and injury

RISK OF INJURY! Check every bulb and lampshade for damage immediately upon unpacking. Do not fit the light if the bulbs and / or lampshades are faulty. If they are, contact the service point for a replacement.
RISK OF INJURY FROM BURNS! Ensure the lamp has been switched off and allowed to cool before you touch it. In this way you will avoid the danger of burns. Bulbs give off a lot of heat around the top of the lamp.
- Replace any faulty bulbs with new ones immediately. Before replacing the bulb, always remove the fuse or switch the automatic cutout off.

FIREHAZARD! Fit the light so that it is at least 0.3 m away from the material illuminated.

DANGER OF EXPLOSION!

Never use the product in rooms or in the vicinity of easily inflammable or explosive liquids, gases, vapours or dusts.

CAUTION! DANGER OF FIRE!

Never cover the downlights with thermally insulative covers or similar materials.

• Please ensure there is adequate cooling! The maximum temperature in the downlight installation area of 90 °C must not be exceeded.
• Use the downlight set only with the supplied accessories. Do not interconnect downlight sets. Failure to observe this advice invalidates your rights under the warranty.
• Do not allow the lamp or the packaging materials to lie around unattended. Plastic film or bags, Styrofoam etc. can turn into dangerous toys for children.

Working safely

• Install the light so that it is protected from moisture, dirt and the build-up of excessive heat. Do not install the downlights in bathrooms or similar rooms.
  Use only 230-240 V\~bulbs with a GU10 socket and a maximum power of 50 watts.
  ■ The distance between two installation spotlights must be at least 20 cm.
  The clearance above and to the sides of the lamp fitting must be at least 10 cm (see Fig. M).
  ■ Make careful preparations for the assembly and take sufficient time. Clearly lay out all components and any additional tools or materials that might be required so that they are readily to hand.
• Remain alert at all times and always watch what you are doing. Always proceed with caution and do not assemble the lamp if you cannot concentrate or feel unwell.

● Preparation

● Required tools and materials

The tools and materials mentioned are not included in the delivery. The details and values given are non-binding and for guidance only. The nature of the material depends on the individual circumstances on site.

• Cable H03VV-2F of the required length with wire end ferrules (minimum cross-section 2 x 0.75 mm²)
• Pencil / Marking tool
• Voltage tester
  -Screwdriver
• Electric drill
• Hole cutter
• Edge cutter
• Ladder

● Before installation

Important: The electrical connection must be carried out by a qualified electrician or someone trained to perform electrical installations. This person must be familiar with the features of the light and the connection requirements.

☐ Familiarise yourself with all instructions and diagrams in this manual as well as with the light before installation.
Before installation, ensure that the cable that the light is to be attached to is not live. Remove its fuse or switch off the automatic cutout in the fuse box (0 position, see Fig. A).
☐ Use the voltage tester to check that there is no voltage.

● Preparations for use

- Installation

☐ Mark the positions of the installation spotlights. Use the hole cutter ( 68 mm) to drill the 6 holes at the installation point (see Fig. B). Please take into account the distance between two installation spotlights. This must be at least 20 cm.
☐ Guide the power line through the installation opening (see Fig. C).
☐ Insert the retaining springs 4 into the spotlights (see Fig. E and F). The small lug of the retaining springs 4 must lie on the inside of the housing of the lamp 1 so that the retaining springs 4 can receive the electric current.

☐ Open the mains socket 8 by unscrewing the cover 5 with a screwdriver (see Fig. G).
☐ Release the cable holder 7 using a screwdriver.
☐ Connect the power line to the terminal block 6 (see Fig. G) and tighten the cable holder 7 with a screwdriver. Pay attention to the L/N marking (L = black or brown, N = blue) of the connected wires. Any green / yellow wire present is not connected, no earth connection, as the lamp belongs to protection class II. Use a cable of type H03VV-2F with a minimum cross-section of 2 × 0.75 mm^2 and wire end ferrules.
☐ Seal the mains socket 8 again by tightening the cover 5 with a screwdriver.
☐ Fit the mains connection box 8 back into the installation opening.
☐ Pull the socket 9 with its connection cable out of each opening.
Place the fitting 9 of the mains socket 8 on the bulb 2 including the lamp housing 1 and turn the bulb 2 with a 14 turn in a clockwise direction until it is tight (see Fig. H).
Before using the downlight spots remove any insulation from around the area of the mains connection box 8 and the downlight spots (see Fig. 1).
☐ Fold the two retaining springs 4 upwards and guide the installation spotlights with the connection cable into the installation opening (see Fig. J). After you have pushed the spotlight into the opening, unfold the retaining springs 4 use them to fix the installation spotlight in place (see Fig. K). Proceed in the same way with the five other installation spotlights.
☐ The downlights are now ready for use.
☐ Now switch on the power supply (see Fig. L).

● Changing the bulbs

CAUTION! DANGER OF ELECTRIC SHOCK! When changing the bulbs, first disconnect the light from the mains

supply. Remove its fuse or switch off the automatic cutout in the fuse box (0 position).

□ Allow the lamp to cool down completely.
☐ Remove the spring washer 3 from the lamp housing 1.
☐ Pull the defective bulb 2 with the socket 9 slightly out of the lamp housing 1. Use a clean, fluff-free cloth when you are replacing a bulb.
☐ Hold the socket 9 firmly and turn the bulb 2 ¼-turn anticlockwise out of the socket 9.
☐ Use only 230-240 V \~bulbs with a GU10 socket and a maximum power of 50 watts.
☐ Insert the new bulb 2. Carefully insert it into the socket 9 and turn it 14 -turn clockwise.
☐ Fix the bulb 2 in place in the lamp housing 1 with the spring washer 3. Check that it is correctly seated (see Fig. D).

● Maintenance and Cleaning

CAUTION! DANGER OF ELECTRIC

SHOCK! Before cleaning the lamp make sure that it is isolated from the mains

supply. Remove its fuse or switch off the automatic cutout in the fuse box (0 position).

CAUTION! DANGER OF ELECTRIC

SHOCK! For reasons of electrical safety, the light must never be cleaned with water

or other fluids or be immersed in water. When cleaning, only use a dry, lint-free cloth.

• Do not use any solvents, petrol or similar. This would cause damage to the light.
  ☐ Allow the lamp to cool down completely.

- Disposal

The packaging and ancillary packing consist entirely of environmentally-friendly materials. They can be disposed of at your local recycling facility.

The symbol of the wheelie bin with the line through it means that, in the European Union, the product has to be disposed

of in a separate refuse collection. This applies to the product and to all components bearing this

symbol. Products marked in this way may not be disposed of along with normal domestic waste but have to be handed in at a recycling collection point for electrical and electronic appliances. Recycling helps to reduce the consumption of raw materials and to ease the burden on the environment.

- Information

- Guarantee

You receive a 36 month warranty on this product, valid from the date of purchase.

The device has been carefully produced under strict quality control. Within the warranty period we shall rectify without charge all material and manufacturing defects. In the event of a defect arising during the warranty period, please send the device to the listed Service Centre address, making reference to the following article number: 6729.

Wear parts (such as bulbs) and damage caused by improper handling, non-observance of the operating instructions or unauthorised interference are excluded from the warranty.

The performance of services under the warranty does not extend or renew the warranty period.

Service

● Declaration of Conformity

This product fulfils the requirements of the applicable European and national directives (Electromagnetic Compatibility 2004/108/EC, Low Voltage Directive 2006/95/EC). Conformity has been demonstrated. The relevant declarations and documents are held by the manufacturer.

Johdanto

Montering....Side 26

EXPLOSIONSGEFAHR! Verwen-

59929 Brilon (Germany)

© by ORFGEN Marketing

Last Information Update · Tietojen tila

Informationsstatus · Tilstand af information

Abstract geometric shape resembling a stylized letter 'L' in white on a dark background (no text or symbols)