GRS 3820 Magnetic - Beard trimmer ECG - Free user manual and instructions

Product Type	Beard Trimmer / Hair Clipper
Model	GRS 3820 Magnetic
Brand	ECG
Dimensions	Approx. 18 x 4 x 4 cm
Weight	Approx. 200 g (without accessories)
Power Supply	USB charging via magnetic connector; Adapter input 100-240V~ 50/60 Hz 0.2A; Output DC 5V / 1.0A
Battery	Li-ion 500 mAh
Charging Time	Approx. 2 hours
Operating Time	Approx. 60 minutes on full charge
LED Indicator	Red while charging, green when fully charged, white when operating
Cutting Heads	Interchangeable: T-shaped blade for hair, U-shaped blade for beard, 3.5 mm detail trimmer
Comb Attachments	For hair: 4, 9, 12, 16 mm; For beard: 1, 2 mm, variable 3-7 mm, and special comb; Also left/right gradient attachments for hair
Minimum Cutting Length	0.5 mm (without comb)
Usage	For dry hair and beard only; home use
Cleaning	Remove comb attachments and rinse with water; clean blade head with brush; lubricate with silicone oil after use
Safety	Do not immerse in water; keep dry; use only original accessories; suitable for children 8+ with supervision
Included Accessories	USB cable with magnetic connector, adapter, comb, oil, cleaning brush, travel case, multiple heads and combs
Manufacturer	K+B Progres, a.s., U Expertu 91, 250 69 Klíčany, Czech Republic

Frequently Asked Questions - GRS 3820 Magnetic ECG

How long does it take to fully charge the GRS 3820 Magnetic?

Charging takes approximately 2 hours. The LED turns green when fully charged.

How long does the battery last on a full charge?

The operating time is about 60 minutes with a fully charged battery.

Can I use the trimmer on wet hair?

No, the trimmer is designed for dry hair only. Do not use on wet hair or in the shower.

How do I change the cutting head?

Squeeze the tabs on the sides of the trimmer body to release the head, then pull it out. To attach a new head, push it in until you hear a click.

How do I adjust the cutting length?

Attach the appropriate comb attachment to the head. The cutting height is printed on each attachment. For a minimum length of 0.5 mm, use without a comb.

How should I clean the trimmer?

Remove the comb attachments and rinse them with water. Clean the blade head with the included cleaning brush (do not use water on the head). Lubricate the moving teeth with silicone oil after each use.

Is the GRS 3820 Magnetic suitable for beard trimming?

Yes, it comes with a U-shaped blade head and specialized combs for beard grooming (1 mm, 2 mm, variable 3-7 mm).

Can I use the trimmer while it is charging?

The manual recommends using the trimmer only when it is not connected to the charger. Charge it fully before use.

What should I do if the blades stop moving smoothly?

First, check if the heads are clean and lubricated. If the problem persists, contact the service center. Do not attempt to repair the device yourself.

How do I dispose of the trimmer at the end of its life?

Do not dispose of it with household waste. Hand it over to a designated recycling point for electrical and electronic equipment. The Li-ion battery must be removed and disposed of separately.

USER MANUAL GRS 3820 Magnetic ECG

ZS 2620 Magnetic GRS 3820 Magnetic

TRIMMER

INSTRUCTION MANUAL

English

1. Body of the clipper
2. Head release button
3. Sliding switch 0/1
4. Head with T-shaped blades for styling hair
5. Comb attachments for hair styling with cutting height 4/9/12/16 mm
6. Comb attachments (left and right) for gradual haircutting
7. Head with blades for detailed trimming - width 3.5 mm
8. Magnetic connector for USB charging
9. USB power cable with magnetic connector
10. Adapter
11. Comb
    12.Oil
    13.Cleaning brush
12. Travel case

Only for GRS 3820 Magnetic:

A) Head with "U" shaped blades for beard grooming

B) Comb attachments for beard grooming with 1/2 mm cutting height
C) Comb attachment for beard grooming with variable cutting height 3-7 mm
D) Special comb for beard grooming

Deutsch

Tik GRS 3820 Magnetic:

Read carefully and save for future use!

Warning: The safety measures and instructions, contained in this manual, do not include all conditions and situations possible. The user must understand that common sense, caution and care are factors that cannot be integrated into any product. Therefore, these factors shall be ensured by the user/s using and operating this appliance. We are not liable for damages caused during shipping, by incorrect use, voltage fluctuation or the modification or adjustment of any part of the appliance. Read the operating instructions carefully before using the device for the first time and follow the safety instructions! The device may only be used as described in this manual. - Save the manual for future reference. If you pass the device to another person, please add this manual.

SAFETY INSTRUCTIONS

Use the trimmer only on dry hair. The device is designed for home use and must not be used for commercial purposes. The device may be used only indoors. • Possible misuses: do not use the device to cut artificial hair or animal hair. • Instructions for safe operation: use only the original power supply provided for connection to the mains. • This appliance is intended for use by children 8 years of age and older and persons with reduced physical or mental abilities or lack of experience and knowledge, provided they are under supervision or given instructions concerning use of the appliance in a safe manner and

understand the potential hazards. Children shall not play with the appliance. Cleaning and maintenance by the user must not be done by children unless they are older than 8 years old and under supervision. Children under 8 years of age must stay away from the appliance and its supply • Keep the appliance dry.

GB

- DANGER of electric shock due to moisture (when charging). • Never place the unit in such a way that it could fall into the water while still connected to the power cord. • Protect the device from moisture, dripping or splashing water. • Never touch the device with wet hands. • Neither the device nor the power cord may be immersed in water or other liquids or rinsed under running water. • If the device falls into the water, disconnect the mains cable immediately before removing the device from the water. Do not use the device afterwards, but have it checked by a specialized technician. • If liquid enters the unit or the power cord, have it checked before turning it back on. • If you use the device in the bathroom, the power cord must be unplugged after use, as the proximity of water poses a risk even when the device is switched off. • Before connecting the trimmer to the mains for the first time, make sure that the voltage of your mains supply corresponds to the operating voltage indicated on the label of the device. The outlet must be installed in accordance with applicable electrical codes according to EN. • DANGER of electric shock.

- Do not use the trimmer if the device or the power cord shows visible signs of damage or if you have

GB

dropped it. • Connect the USB cable connector to the device first, then to the power source. • The electrical outlet must be easily accessible after connection. • Ensure that the cable can not be damaged by sharp edges or hot surfaces. • Unplug the adapter from the power supply after each charging when it is malfunctioning and during thunderstorms. • When disconnecting, never pull the cable, but grasp the fork. • To avoid any risk, do not make any changes to the device or accessories. Repairs must be carried out by a specialized company. • DANGER! Please observe the following instructions when handling the batteries: Charge the device using only the original power supply. • Protect the batteries from mechanical damage. • Do not expose the device to direct sunlight and high temperatures. If the device is heated to more than 125 °C, the batteries may ignite. • Do not leave the device near a source of burning, as it may cause fire. Conventional extinguishing agents can be used for extinguishing (ABC powder extinguishers, CO2 extinguishers). • If liquids leak from the batteries, avoid contact with eyes, mucous membranes and skin as well as inhalation of vapors. Immediately rinse the affected area with plenty of clean water. In any case, contact a physician. • Leaked fluids must be absorbed with an absorbent and properly disposed off. • Open batteries are a hazardous waste and therefore have to be disposed off properly. WARNING! Risk of cuts. • The blades are very sharp. Handle them carefully. • Do not use the device when the head or the attachment

are damaged. • Always disconnect the device before cleaning. • WARNING! Risk of injury. • Do not use the device in open wounds, cutting wounds, sunburns and blisters. • WARNING! Danger of injury by the trimmer oil. • Keep the small container of oil out of the reach of children. • Avoid contact of the trimmer oil with your eyes. If the oil of the trimmer gets into your eyes, rinse them out immediately with plenty of water and remove the oil completely. • Never swallow the trimmer oil. • CAUTION! Property damage. • Use original accessories only. • Never place the device on hot surfaces (e.g. hot plates) or near sources of heat or naked flames. • Do not cover the power source to prevent overheating. • Do not use coarse or abrasive cleaners.

Before first use

• After transporting or storing in cold conditions, the device must be allowed to acclimate at room temperature for at least 2 hours.
- Before cutting for the first time, switch on the trimmer by moving the switch to the I and make sure the machine is working normally and the blades are moving smoothly.

CHARGING

Charging

CAUTION! Property damage

Note that the battery capacity will be reduced after extended periods of storage and non-use. Do not charge the trimmer for more than 24 hours at a time. Do not leave the trimmer permanently connected to a charging source.

WARNING: Use only the USB cable/adapter supplied with the trimmer for charging. Make sure before charging that the switch is in the 0position.

NOTES

GB

Connect the USB cable to the machine and the power source. If using an adapter (included), connect it to an easily accessible electrical outlet. The red LED on the body of the trimmer lights up permanently when connected to the power source.

Warning: A fully charged battery (after about 2 hours of charging) is indicated by a green LED. The operating time with a fully charged battery is about 60 minutes.

USING THE APPLIANCE

NOTES:

The GRS 3820 Magnetic is designed for hair and beard grooming. The ZS 2620 Magnetic is designed for hair styling. • The beard/hair cut must be dry. • The T-shaped head and comb attachments are designed for styling hair • The head with 3.5 mm wide blades is designed for detailed shaping of eyebrows and beard, or for cutting out shapes in the hairstyle. • For beard grooming (only on the GRS 3820 Magnetic model), the U-shaped comb head + special comb is designed. • Switch on the device by moving the switch to position I (the LED is white). Slide the switch to position 0 to switch the unit off.

Setting the cut length

The cutting height (information in mm is printed directly on the attachment) is determined by using the appropriate comb attachment. When replacing the attachments, make sure that it is correctly attached to the head (you will hear a click). For a minimum cutting height (0.5 mm), the trimmer can be used without the comb attachment. To remove the comb attachment, gently push the attachment from the back of the device with your thumb until it releases from the lock.

Replacing the head with blades

Squeeze the tabs on the sides of the trimmer body to release the head. Pull it out of the device in the direction of the arrow on the head. When putting the head back on, make sure that it fits well into the device (you will hear a click).

TRIMMING

The length of the cut may vary according to the cutting angle. First, start with the comb attachment set to the longest cut, then use shorter cutting lengths during the cutting process. Comb through the hair/beard before styling.

Hair Trimming

Position the person being cut so that their head is at eye level. Cover her shoulders

with a towel. Always start cutting from the back of the head. Cut against the direction of hair growth and work towards the centre of the head. The left and right extensions are designed for gradual haircutting, e.g. on the sides of the head for men's haircuts.

GB

Beard trimming

Trim the beard in the direction of growth. For a smooth shaved face, use the shaver without the attachment. For light stubble, the attachment with a height of 1 mm and trimming under the nose of 2 mm. Use the variable height attachment to trim a moustache or beard.

NOTE: Always turn off the trimmer during breaks in cutting.

CLEANING AND MAINTENANCE

Turn off the device. Remove the removable comb attachment and rinse with water. Before reassembly, allow it to dry thoroughly. Use the included cleaning brush to clean the cutting head with the blades. Never clean the blade head with water or any other liquid. We recommend gently lubricating the moving teeth of the cutting edges with silicone oil after each use. You can use the supplied oil. Use only acid free oil. For lubrication, DO NOT USE vegetable oils, grease or oils with solvents. The solvents evaporate, leaving a thick layer of lubricant, which can slow down the movement of the blades. Remove excess lubricant with a dry, lint-free cloth.

TROUBLESHOOTING

DANGER!

Do not attempt to repair the device by yourself. Whenever a malfunction occurs, pull the plug out of the electrical outlet.

Malfunction: Check the following:
The device does not work Is the battery empty?
The heads of the trimmer do not work smoothly	Are the heads clean and lubricated?

If any of the above-mentioned malfunctions occur, contact our service center without delay.

Repairs must be carried out by a specialized company.

TECHNICAL SPECIFICATIONS

AdapterInputOutputProtection classOperating conditions	100-240V ~ 50/60 HZ, 0.2 A max.DC 5 V / 1.0 A, 5 W□IIDesigned exclusively for useindoors
Hair clipperBatteryPermissible ambient temperature	Li-ion battery 500 mAhfrom 5°C to +35°C

We reserve the right to make technical and visual changes to the device or its accessories for the continuous improvement of the product.

DISPOSAL

USE AND DISPOSAL OF WASTE

Wrapping paper and corrugated paperboard – deliver to scrapyard. Packing foil, PE bags, plastic elements – throw into plastic recycling containers.

DISPOSAL OF PRODUCTS AT THE END OF LIFETIME

Disposal of old electrical & electronic equipment (applicable in the EU Member States and other European countries with separate collection systems)

The represented symbol on the product or package means the product shall not be treated as domestic waste. Hand over the product to the specified location for recycling electric and electronic equipment. Prevent negative impacts on human health and the environment by properly recycling your product. Recycling contributes to preserving natural resources. For more information on the recycling of this product, refer to your local authority, domestic waste processing organization or store, where you purchased the product. Dispose of the lubricant container only after it's emptied.

The Li-ion battery used in this unit must not be disposed of in mixed household waste. The battery must be properly disposed off. For more information, contact battery distributors or waste collection points.

This product complies with EU directives on electromagnetic compatibility and electrical safety.

08/05

Li-ion

The operating instructions are available on the website www.ecg-electro.eu. Changes of text and technical parameters reserved.

BEZBEDNOSNA UPUTSTVA

250 69 Klíčany, Czech Rep. e-post: [e-mail]

Hrvatski

K+B Progres, a.s.

U Expertu 91 tel.: [phone]

250 69 Klíčany, Czech Rep.

e-mail: [e-mail]

Bosanski

K+B Progres, a.s.

U Expertu 91 tel.: [phone]

250 69 Klíčany, Czech Rep.

e-mail: [e-mail]

Latviešu valoda

K+B Progres, a.s.

U Expertu 91 tel.: [phone]

250 69 Klíčany, Czech Rep.

e-pasts: [e-mail]

Lietuvių kalba

K+B Progres, a.s.

U Expertu 91 tel.: [phone]

250 69 Klíčany, Czech Rep. el. paštas: [e-mail]

Magyar

K+B Progres, a.s.

U Expertu 91 tel.: [phone]

250 69 Klíčany, Czech Rep. e-mail: [e-mail]

Polski

K+B Progres, a.s.

U Expertu 91 tel.: [phone]

250 69 Klíčany, Czech Rep. e-mail: [e-mail]

Română

K+B Progres, a.s.

U Expertu 91 tel.: [phone]

250 69 Klíčany, Czech Rep. e-mail: [e-mail]

Slovenčina

250 69 Klíčany, Czech Rep.

e-mail: [e-mail]

Srpski

K+B Progres, a.s.

U Expertu 91 tel.: [phone]

250 69 Klíčany, Czech Rep.

e-pošta: [e-mail]

Crnogorski

K+B Progres, a.s.

U Expertu 91 tel.: [phone]

250 69 Klíčany, Czech Rep.

e-pošta: [e-mail]

Ελληνικά

K+B Progres, a.s.

U Expertu 91 τηλ.: [phone]