XS 6B0M4PDB-08 - Dishwasher HAIER - Free user manual and instructions

Brand	Haier
Model	XS 6B0M4PDB-08
Product type	Built-in dishwasher
Height (adjustable)	818 - 898 mm
Width	596 mm
Depth	550 mm
Required water pressure	0.08 - 1 MPa
Power supply	220-240 V ~ 50 Hz
Safety device	Anti-overflow
Included accessories	Anti-steam tape, protective film, screws, drilling template
Maximum kitchen panel weight	9 kg
Height adjustment	Adjustable rear and front feet
Tilt adjustment	Possible via feet
Installation type	Built-in, side fixation or under worktop
Condenser component	Integrated and adjustable according to door height

Frequently Asked Questions - XS 6B0M4PDB-08 HAIER

How to adjust the height of the dishwasher?

Tilt the dishwasher by lifting the rear about 10 cm, then adjust the height of the rear foot from the front of the machine. Then adjust the front feet directly. The total height can vary from 818 to 898 mm.

What is the required water pressure?

The water pressure must be between 0.08 MPa and 1 MPa. Make sure the pressure is within this range before connecting.

How to install the kitchen panel?

Measure the distance between the top edge of adjacent doors and the dishwasher. Transfer this measurement to the panel, apply the supplied drilling template, then drill. Insert the top pins into the dishwasher slots, fix the panel to the lower part, and push down. Be careful not to let the handle screws protrude at the back.

What to do if the door does not close properly?

First check the leveling of the dishwasher. If the appliance is not level, the door may not close properly and may let steam out. Adjust the tilt via the front and rear feet to achieve a perfect balance.

Can I install the dishwasher under a hob?

No, it is strictly forbidden to install the dishwasher under a hob. Also do not install the product near heat sources (radiators, stoves).

How to fix the dishwasher if adjacent furniture does not allow side fixation?

Use the supplied brackets to fix the appliance to the worktop. Be careful about the worktop material: if it is not wood, take additional precautions.

What is the maximum weight of the kitchen panel?

The kitchen panel must not exceed 9 kg. If the panel is heavier, contact customer service.

How to assemble the condenser component?

Adjust the size of the component (L) according to the height of the kitchen door. Insert it into the designated space and fix it using the supplied screws.

Where to install the anti-steam tape?

Apply the anti-steam tape under the worktop and on the sides of adjacent furniture to protect them from moisture.

How to dismantle the dishwasher for a move?

First disconnect the appliance from the electrical and water supply. Unscrew the fixing screws, slightly lift the product, and remove it completely. The furniture is not damaged and can be reused.

USER MANUAL XS 6B0M4PDB-08 HAIER

Sliding movement hinges with Ultra Dry system

Haier

FROM CLEAN

TO SHINE

EN | IT | FR | DE | ES | GR | NL | PT | SK | PL | CZ | RO | HU

SL | SR | LT | EE | LV | BG | HR | DA | FI | NO | SV | UA | TR

WELCOME

This installation manual is designed for kitchen manufacturers who will deal with these products. To ensure safety and get the best results, please read this manual carefully, including the safety instructions, and keep it for future reference. Before proceeding with the installation, take note of the serial number, as you may need it in case of repairs. Check for any damage during transport and consult a technician when in doubt before using. Always keep all packing material away from children.

NOTE: Features, pictures in the manual and product accessories may vary depending on the model purchased.

Index

1 Safety warnings for installation p.2-3 2 Where to install the dishwasher p.3 3 Dishwasher dimensions p.4-5 4 Step-by-step installation video p.6 5 Installation tools p.6 6 Built-in dimensions p.7 7 Instructions for dishwasher installation p.8 - 17

7.1 Condenser component assembly 7.2 Steam band installation 7.3 Height adjustment 7.4 Rear foot adjustment 7.5 Front feet adjustment 7.6 Inclination adjustment 7.7 Insertion into the built-in compartment 7.8 Fixing the front feet 7.9 Panel preparation 7.10 Panel installation 7.11 Fixing the machine to the kitchen

8 Drain water and electricity connection p.18-19

8.1 Connection diagram 8.2 Safety devices

9 Delivery to the user p.19

10 Disassembling the dishwasher p.19

1 Safety warnings for installation

Observe these directions before beginning the installation of the product. Your safety is very important to us. Please read this information carefully before using the product.

• Installation must be carried out by a qualified technician who must know and respect the laws in force in the country of installation and the manufacturer's instructions.
• If manufacturer service is required to eliminate faults resulting from improper installation, such service is not covered by the fix.
• Remove the packing material before operating the appliance.
• After unboxing the appliance, always check it is not damaged. In case of issue, contact the customer service before installing and do not connect to the power supply.
• A damaged product can be the cause of a short circuit, electric shock, fire start, and other hazards.
• Check the packaging for accessories or accompanying materials (envelopes with screws, documents, brochures, etc.) and, if so, remove and store them.
• Incorrect installation may cause harm or injury to people, animals, or belongings. The manufacturer cannot be held responsible for such harm or injury.
• Safe use is only guaranteed if installation has been carried out properly according to these instructions. In case of damage due to improper installation, the responsibility lies with the person who installed the product.
• During installation, the appliance must not be connected to the power supply.
• It is recommended to wear protective gloves during installation to avoid cut injuries.
• In case of incorrect installation, tampering with the device, and improper connection, the validity of the product warranty will expire.
• Make sure that when the product's power supply cable is completed, it is not accessible.
• After assembly, the power cord must not come into contact with moving parts of kitchen components (such as a drawer) and must not be exposed to mechanical stresses.
• When delivering the product to the end user, the technician must ensure that it has been installed correctly.
• Do not connect the product to the electrical network until the front panel has been fully installed. Otherwise, there may be an electrical hazard. Take care during transport, the product is heavy.
• Before starting the installation, check all the dimensions of the built-in compartment by comparing them with the instructions contained in this manual. Note that it is possible to align the door with the doors of other furniture, even if it exceeds the control panel in height.
• Make sure the installation area is stable and solid.
• Apply the protective film, supplied in the installation kit, under the worktop and on surrounding furniture. This film protects the furniture from humidity.
• Be careful when opening and closing the product.
• Incorrect installation can cause the product to tip over.
• The product must be level to function correctly, otherwise the door will not close properly, leading to the escape of hot steam.

Where to install the dishwasher

• Install and use this product in a closed, covered, dry and well-ventilated environment.
• Do not install the product in open environments exposed to atmospheric agents.
• Mount the product near an electrical outlet;
• Use the product only when placed in a recessed compartment, otherwise you risk injury and burns;
• Do not install the dishwasher under a cooktop/hob;
• Do not install the product near heat sources (radiators, stoves, etc.);
• Do not place the product on carpets or similar surfaces;
• Place the product on a clean, level, and stable surface.

3 Dishwasher dimensions

Dimensions in mm

Front axonometric view of the product

Front axonometric view with kitchen door

WARNING: If the kitchen panel is heavier than 9kg, contact the service center.

Dimensions in mm

Back view

Side view

4 Step-by-step installation video

You can view the product installation video by scanning the QR code:

or by clicking this link.

5 Installation tools

Tools needed

Tools provided with the product

Dimensions in mm

Axonometric view

A

WARNING: The minimum height of the dishwasher is 818 mm; in this case, the distance between the kitchen door and the floor must be between 90 and 120 mm. If the dishwasher is raised (max. 898 mm), the door-to-floor distance must also increase proportionally, up to a maximum between 170 and 200 mm.

7 Instructions for dishwasher installation

7.1 Condenser component assembly

1.

Adjust the size of the component (L), based on the height of the kitchen door;

Condenser component assembly 7.1

2.

Insert component (L) inside the provided space, as indicated in the figure below;

3.

Fix component (L) by screwing it using the included screws;

7 Instructions for dishwasher installation

Steam band installation 7.2

Apply the sticker band under the worktop and to the sides of the adjacent furniture.

7.3 Height adjustment

Incline the dishwasher by raising the back about 10 cm.

7.4 Rear foot adjustment

Adjust the rear foot height by operating from the front of the machine as indicated below.

7 Instructions for dishwasher installation

7.5 Front feet adjustment

Adjust the front feet directly. If necessary, lift the dishwasher slightly.

7.6 Inclination adjustment

Level the dishwasher by the vertical and horizontal planes.

7.7 Insertion into the built-in compartment

Insert the dishwasher into the built-in compartment and verify measurements and tolerances.

7.8 Fixing the front feet

After checking all measurements, permanently secure the front feet to prevent them from loosening over time. This operation can also be performed after applying the kitchen panel.

7 Instructions for dishwasher installation

7.9 Panel preparation

1.

Measure the distance between the top edge of the adjacent doors and the dishwasher;

2.

Transfer the measurement onto the kitchen panel and locate the center;

3.

Apply the drilling template and follow the instructions provided;

7.9 Panel preparation

4.

Remove the drilling template and apply the accessories.

WARNING: Ensure screw heads don't protrude from the panel's rear surface, especially if you install the handle.

7 Instructions for dishwasher installation

7.9 Panel installation

1.

Insert the upper pins into the dishwasher slots;

2.

Fix the panel using the lower hooks;

3.

Push the panel downwards.

⚠ WARNING: Connect the dishwasher to the water and electrical mains at this time, observing the instructions provided in chapter 8

7.10 Fixing the machine to the kitchen

Instructions for fixing the dishwasher to the side of adjacent cabinets.

WARNING: If you can't fix the dishwasher laterally, use the brackets provided and secure it to the worktop; be careful if the worktop material is not wood.

8 Drain water and electricity connection

8.1 Connection diagram

Column installation diagram

WARNING: Ensure that the water pressure is between 0.08 MPa and 1 MPa.

8.2 Safety devices

All dishwashers are equipped with an anti-overflow safety device which, in the event that the water exceeds the normal level due to a malfunction, automatically blocks the water flow and/or drains the excess water.

See the User Manual for more details.

Delivery to the user

9

At the end of installation:

• Inform the user about essential functions;
• Inform the user about all aspects relevant to safe use and handling;
• Deliver accessories and instructions for use and assembly to the user to be kept with care.

After installation is complete, remove the protective film, tape, and all other packing materials and remove the supplied accessories from inside the product.

NOTE: The actual appearance of the product depends on the model chosen.

Disassembling the dishwasher

10

• Disconnect the product from the power supply;
• Unscrew the fixing screws;
• Lift the product slightly and pull it out completely;
• This product will not damage the cabinet, which can also be used with a new appliance.

Haier

WELCOME

3.

2.

3.

Haier

WELCOME

8.1 Connection diagram 8.2 Safety devices

3.

2.

2.

3.

Haier

WELCOME

1. 

3.

2.

2.

3.

Haier

WELCOME

7.4 Adjusting the rear foot

2.

2.

3.

Haier

WELCOME

1. 

3.

7.3 Height adjustment

2.

2.

3.

Haier

WELCOME

3.

7.3 Height adjustment

7.6 Tilt adjustment

Level the dishwasher with respect to the vertical and horizontal plane.

2.

2.

3.

Haier

WELCOME

3.

2.

2.

3.

Haier

WELCOME

3.

7.6 Setting the tilt

2.

Transfer the dimension to the kitchen panel and determine the center;

3.

7.9 Preparing the panel

4.

2.

3.

Press the panel down.

Haier

WELCOME

3.

2.

Haier

WELCOME

3.

7.3 Height adjustment

2.

7.9 Panel preparation

4.

2.

3.

Haier

WELCOME

3.

2.

2.

3.

Haier

WELCOME

3.

7.3 Height adjustment

2.

2.

3.

Press down on the panel;

Haier

WELCOME

⚠ CAUTION: The minimum height of the dishwasher is 818 mm; in this case, the distance between the kitchen door and the floor must be between 90 and 120 mm. If the dishwasher is raised (max. 898 mm), the distance between the door and the floor must be proportionally increased up to a maximum of between 170 and 200 mm.

3.

2.

Transfer the measurement to the kitchen panel and determine the center;

3.

Install the drilling template and follow the enclosed instructions;

7.9 Panel preparation

4.

Remove the template and install the accessories;

2.

3.

Press the panel downwards.

⚠ WARNING: If you cannot secure the dishwasher laterally, use the supplied brackets and attach it to the worktop; be careful if the worktop material is not wood.

Haier

WELCOME

This installation instruction is designed for kitchen manufacturers who will work with these products. To ensure safety and achieve the best results, carefully read this instruction, including the safety instructions, and keep it for future reference. Before proceeding with the installation, pay attention to the serial number, as you may need it in case of repairs. Check for any transport damage and consult a technician if you are in doubt before use. Always keep all packaging material away from children.

NOTE: Features, images in the manual, and additional equipment of the product may vary depending on the model purchased.

Index

or click on this

5 Installation tools

Required tools

⚠ WARNING: The minimum height of the dishwasher is 818 mm; in that case, the distance between the kitchen door and the floor must be between 90 and 120 mm. If the dishwasher is raised (max. 898 mm), the distance from the door to the floor must also increase proportionally, up to a maximum of 170 and 200 mm.

7 Installation instructions for the dishwasher

7.1 Assembly of condenser components

1.

3.

7.3 Height adjustment

Tilt the dishwasher by lifting the rear part by about 10 cm.

7.8 Securing the front feet

After checking all measurements, permanently attach the front feet to prevent them from loosening over time. This can also be done after installing the kitchen countertop.

7 Installation instructions for the dishwasher

7.9 Preparing the countertop

1.

Measure the distance between the top edge of adjacent doors and the dishwasher;

2.

Transfer the measurement to the kitchen countertop and locate the center;

3.

Apply the drilling template and follow the provided instructions;

7.9 Preparing the countertop

4.

nc

7 Installation instructions for the dishwasher

7.10 Installing the countertop

1.

3.

Lower the panel.

⚠ WARNING: Connect the dishwasher to the water supply and electrical mains at this point, following the instructions given in chapter 8.

7.11 Securing the dishwasher to the kitchen

Instructions for securing the dishwasher laterally to adjacent kitchen units.

⚠ WARNING: If you cannot secure the dishwasher laterally, use the supplied brackets and secure it to the worktop; be careful if the worktop material is not wood.

3.

7.6 Adjustment of the legs

2.

7 Installation instructions for the dishwasher

7.10 Panel installation

1.

2.

3.

Press the panel downward.

Haier

THIS IS IMPORTANT

3.

7.4 Adjusting the rear foot

7.6 Adjusting the tilt angle

7.8 Securing the front feet

2.

7.9 Preparing the panel

4.

2.

3.

Press the panel downward;

Haier

PLEASE READ

Or by clicking on this link

3.

2.

2.

3.

Press the panel down;

Haier

WELCOME

1. 

2.

3.

Press the panel down.

Haier

WELCOME

⚠ WARNING: The minimum height of the dishwasher is 818 mm; in that case, the distance between the kitchen door and the floor must be between 90 and 120 mm. If the dishwasher is raised (max. 898 mm), this distance must also be increased proportionally, up to a maximum of between 170 and 200 mm.

7 Dishwasher installation instructions

7.1 Assembling the condenser component

1.

Adjust the size of the component (L) according to the height of the kitchen door;

7.1 Assembling the condenser component

2.

Insert the component (L) into the designated space, as shown in the figure below;

3.

Secure the component (L) with the screws provided.

7 Dishwasher installation instructions

7.2 Installing the steam strip

3.

7.3 Adjusting the height

7.4 Adjusting the rear foot

Adjust the height of the rear foot from the front of the machine according to the instructions.

7 Dishwasher installation instructions

7.5 Adjusting the height of the front feet

Act directly on the front feet. If necessary, gently lift the dishwasher.

7.6 Adjusting the tilt

Align the dishwasher vertically and horizontally.

7.7 Inserting into the built-in space

2.

7.9 Preparing the panel

4.

Remove the template and install the accessories.

⚠️ CAUTION: Avoid having the screw heads protrude from the back of the panel when installing the handle.

7 Dishwasher installation instructions

7.10 Panel installation

1.

Insert the upper pins into the slots of the dishwasher;

2.

Attach the panel to the bottom of the dishwasher;

3.

⚠ WARNING: If you cannot secure the dishwasher laterally, use the supplied brackets and attach it to the worktop; be careful if the worktop material is not wood.

Haier

WELCOME

3.

7.3 Height adjustment

7.6 Angle adjustment

2.

2.

3.

Push the panel downwards;

Haier

WELCOME

7.3 Height adjustment

Tilt the dishwasher by lifting the rear about 10 cm.

7.4 Rear foot adjustment

2.

2.

3.

Press the panel downward.

Haier

WELCOME

3.

7.3 Height adjustment

7.6 Angle adjustment

2.

2.

3.

Push the panel down.

Haier

WELCOME

3.

7.3 Height adjustment

7.6 Angle adjustment

2.

3.

Haier

WELCOME!

1. 

2.

3.

Haier

WELCOME

3.

7.3 Height adjustment

7.6 Tilt adjustment

2.

3.

Push the panel downward.

Haier