UMAP 12000 C4 - Portable starter ULTIMATE SPEED - Free user manual and instructions

USER MANUAL UMAP 12000 C4 ULTIMATE SPEED

Black electronic device with attached cables and connectors (no visible text or symbols)

PORTABLE JUMP STARTER WITH POWER BANK UMAP 12000 C4

MOBILE AUTOSTARTHILFE MIT POWERBANK UMAP 12000 C4

AIDE AU DÉMARRAGE MOBILE POUR VOITURES AVEC BATTERIE EXTERNE POWERBANK UMAP 12000 C4

QR code with embedded user icon in center, likely linking to a digital resource or website

PDF ONLINE

www.lidl-service.com

GB IENICY MT

PORTABLE JUMP STARTER WITH POWER BANK

Translation of the original instructions

FRBECH

AIDE AU DÉMARRAGE MOBILE POUR VOITURES AVEC BATTERIE EXTERNE POWERBANK

Icon set with a lowercase 'i' and a stylized open book with a grid pattern, accompanied by an arrow indicating rotation.

GB IE NI CY MT

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

DE AT CH

GB/IE/NI/CY/MT Operation and Safety Notes Page 5

Intended use ......Page 7

Scope of delivery......Page 8

Parts description....Page 8

Technical Specifications......Page 9

General safety instructions ...... Page 10

Specific safety instructions ...... Page 14

Using the device......Page 15

Checking the capacity of the portable

jump starter with power bank......Page 15

Charging the portable jump starter with power bank..Page 16

Using the jumpstart feature......Page 17

Charging mobile phones and tablets......Page 18

Using the 12 V DC output 8 A with

cigarette lighter adapter ......Page 18

Switching the light on....Page 19

FAQs Page 19

Troubleshooting Page 20

Cleaning......Page 20

Storage Page 21

Information about recycling and disposal......Page 21

Original EC Declaration of Conformity ...... Page 22

Warranty and service information......Page 24

Warranty conditions......Page 24

Warranty period and statutory claims for defects......Page 24

Extent of warranty......Page 25

Processing of warranty claims ......Page 25

Service......Page 26

Table of pictograms used
	Read the operating instructions!
	Please note
	Observe warnings and safety instructions!
	The LED bulb is not suitable for domestic room lighting.
	The LED bulb is suitable for extreme temperatures down to -21°C.
	Appliance class III
	The device is only suitable for indoor operation.
	DC voltage in volt
	Made from recycled material
	Packaging material made from corrugated paper
	Keep away from rain and moisture!
	On/off switch for LED
	Risk of serious injury or death!
	Warning: Risk of electric shock!Danger to life!
	Caution! Explosion hazard!
	Don't throw away – recycle!
	Dispose of the device and packaging in an environmentally friendly manner!
	You are legally obliged to place devices marked as such in a collection which is separate from unsorted municipal waste. Disposal through household waste is prohibited.
	Direct current

Portable jump starter with power bank UMAP 12000 C4

- Introduction

Congratulations! You have purchased one of our high-quality products. Please familiarise yourself with the product before using it for the first time. To do this, please read through the following operating and safety instructions carefully. This product must be set up or used only by people who have been trained to do so.

KEEP OUT OF THE REACH OF CHILDREN!

PLEASE NOTE: Only for petrol motors with a max. 3 litre engine and for diesel motors with a max. 2 litre engine.

- Intendeduse

This portable jump starter with power bank serves as additional support for 12 V vehicle battery systems during starting problems in diesel and petrol vehicles, which is caused by weak, empty or faulty starter batteries. However, the portable jump starter with power bank cannot replace the vehicle battery. If no more than 500 A are needed for starting (max. peak current), the power bank lets the user single-handedly start the vehicle when necessary, without additional help from a third party. This portable jump starter with power bank does not serve as additional support for 6 V batteries. The portable jump starter with power bank also has 2 USB outputs. This means that mobile phones, satnavs or other USB-enabled devices can also be charged if needed. Keep these instructions in a safe place. Ensure you hand over all documentation when passing the product on to anyone else. Any use that

differs to the intended use as stated above is prohibited and potentially dangerous. Damage or injury caused by misuse and disregarding the above warning is not covered by the warranty or any liability on the part of the manufacturer. The device is not intended for commercial use. Commercial use will void the guarantee. This product is only intended for standard use.

The LED bulb is not suitable for domestic room lighting.

The LED bulb is suitable for extreme temperatures down to -21°C.

- Scope of delivery

1 portable jump starter with power bank
1 USB C cable
1 jump lead
1 12 V cigarette lighter adapter
1 set of operating instructions
1 storage bag

- Parts description

PLEASE NOTE: After unpacking the product, please check all of the package contents are present and that the device is perfect condition. Do not use the device if it is defective.

For this see Fig. A to F:

8	Power switch for LED light
8a	LED lamp
9	Car jumpstart outlet
10	Jump lead
11	LED box
12	Start LED (green)
13	Error LED (red)
14	12 V/8 A cigarette lighter adapter
15	USB A connector
16	USB C cable
16a	USB C connector
17	Storage bag

PLEASE NOTE: The use of the terms "product" or "device" in the following text refers to the portable jump starter with power bank named in these operating instructions.

• Technical Specifications

The four individual cells used to construct the rechargeable battery pack are connected in series to produce a total voltage of 4 × 3.2V ≈ 12V and a capacity of 3000 mAh. The battery output produced in this way is the same as the output from a rechargeable battery pack with a total capacity of 12000 mAh at 3.2 V.

Model: UMAP 12000 C4
Battery, type: Lithium polymer rechargeable bat-tery pack (F8054106)
Battery, chemical system:	Lithium Iron Phosphate (LiFePO4)
Battery, capacity:	12000 mAh / 3.2 V = 7 38.4 Wh
Charge cycles: 1500
Charging time:	max. 13.5 hours at 1A charge current
Peak current: 500 A
Starting current: 300 A
Operating temperature for power bank:	0-45 °C
Operating temperature for LED:	-21 °C - 45 °C
Voltage: 12 V	---
Input voltage (charging port):	5 V ≠ 1A (USB C)
Capacity: 6650 mAh / 5 V
Output voltage (USB port):	5 V ≠ 1A USB A5 V ≠ 2A USB C

Please note: Only for petrol motors with a max.

3 litre engine and for diesel motors with a max.

2 litre engine.

Changes to technical and visual aspects of the product may be made as part of future developments without notice. Accordingly, no warranty is offered for the physical dimensions, information and specifications in these operating instructions. The operating instructions cannot therefore be used as the basis for asserting a legal claim.

- General safety instructions

This section covers the basic safety regulations applicable when working with the device.

Personal safety:

■ This device may be used by children aged 8 years and older, and by persons with reduced physical, sensory or mental capacities, or a lack of experience

and knowledge, if they are supervised or have been instructed in how to use the device safely and understand the dangers that may arise when using it. Do not allow children to play with the device. Cleaning and day-to-day maintenance must not be performed by children without supervision.

■ Children must be supervised to ensure that they do not play with the device.
- Keep the device away from people – especially children – and household pets.
■ Within the working area, the user is responsible for any damage or injury to third parties that was caused by the use of the device.
- Keep the device in a dry location and out of the reach of children.

⚠️ CAUTION! How to avoid damage to the device and any harm to persons that may result from such damage: Working with the device:

• Do not use the device while driving the vehicle.
  In hot weather, do not leave the device in the car. This could permanently damage the device. Before setup or first use, check the device for any damage and do not use unless in perfect working order.
  ■ Do not expose the device to rain or wet weather and do not allow it to come into

contact with water or to be submerged in water. There is a risk of electric shock!

- Keep all openings of the device free during operation. Do not block the openings with your hands or fingers, and do not cover the device. There is a risk of overheating!

■ Switch the device off and remove the plug from the socket in the following cases:

-when you are not using the device;
-if you are leaving the device unsupervised;
-when you are carrying out cleaning or maintenance work
-if the connection cable is damaged
-if foreign objects have got into the device or you notice unusual noises

■ Only use the accessories supplied and recommended by the manufacturer.

- Do not dismantle or modify the portable jump starter with power bank. This device must only be repaired by a maintenance technician.

■ Do not use the device in areas with a risk of explosion, e.g. near flammable liquids, gases or powders.

■ Do not expose the device to any source of heat.

■ Do not store in places where the temperature can exceed 70 °C.

■ Only charge in an ambient temperature between 0 °C - 40 °C .

■ Only use the USB C cable delivered with the device.

CAUTION!

How to avoid accidents and injuries resulting from electric shock:

Electrical safety:

• Do not carry the device by the cable. Do not unplug the plug from the socket by pulling on the cable. Protect the cable from heat, oil and sharp edges.
  ■ Do not short-circuit the two clips. This can lead to a hazardous situation!
• Do not use the device if the switch cannot be switched on and off. Arrange for damaged switches to be replaced.
  If the cable is damaged, unplug the plug immediately from the socket.

Rechargeable battery packs:

CAUTION! EXPLOSION HAZARD!

Do not short-circuit the rechargeable battery pack and/or open it. This could cause the device to overheat, ignite or explode.

■ Do not expose the rechargeable battery pack to high temperatures. It could explode.

■ Regularly check the rechargeable battery pack for leakage. Leaking or damaged rechargeable battery packs may cause burns to the skin if touched; therefore, always wear suitable safety

gloves! Carefully wipe up the liquid with a cloth and avoid contact with skin and eyes. In the event of contact with skin or eyes, rinse immediately with clean water and seek medical attention.

- Specific safety instructions

■ We recommend charging the portable jump starter with power bank ^2 every 1–2 months. Failure to observe this may result in damage due to deep discharge.
A slightly higher temperature during charging is absolutely normal and not a malfunction. However, we do recommend leaving the portable jump starter with power bank ② to rest for 15 minutes before using.
■ Protect the portable jump starter with power bank ^2 from moisture and high temperatures, including fires.
■ Store the portable jump starter with power bank 2 in a dry place and protect the device from moisture and corrosion.
If you notice the portable jump starter with power bank ② is leaking, producing an unusual odour or looking deformed in any way, stop using the device immediately and contact the manufacturer.
- Do not drop the portable jump starter with power bank ② while it is being used
■ When using the jump lead, ensure that the plug is securely plugged into the

vehicle jumpstart outlet 9.

■ When using the jumpstart, make sure that at least 3 indicator lights ☐ are illuminated.

If the indicator lights for charging status go out during the start attempt, charge the portable jump starter with power bank 2.

If the vehicle does not start after the 3rd – 5th start attempt, stop the start process and check the other causes that may be preventing the vehicle from starting.

• Using the device

- Checking the capacity of the portable jump starter with power bank

PLEASE NOTE: After switching on the portable jump starter with power bank 2 using the power switch 1 the device will switch off automatically after approx. 20 seconds, if a consumer unit is not connected.

To check the capacity of the portable jump starter with power bank 2 press the power switch 1.
■ During charging, the indicator lights will flash
The number of permanently lit indicator light shows the charge level of the portable jump starter with power bank 2.
If the portable jump starter with power banks is completely charged, all indicator lights 7 will light up permanently.

Indicator lights Charge level
not permanent 0%
1 permanently lit 25%
2 permanently lit 50%
3 permanently lit 75%

- Charging the portable jump starter with power bank

■ Connect the USB C cable with the charging port (USB C) 6 and an appropriate USB A socket or an appropriate USB network adapter (working output voltage U_out, max 5 V).

PLEASE NOTE: USB AC adapter not included in the scope of delivery.

PLEASE NOTE: An undervoltage protection circuit is installed in the portable jump starter with power bank 2 to protect the device from damage. This prevents a deep discharge of the portable jump starter with power bank 2 and automatically switches the device off once the rechargeable battery pack is fully discharged. Shortly before the undervoltage protection circuit is activated, the last blue indicator light 7 will start to flash. As soon as the undervoltage protection circuit is activated, the last blue indicator light 7 flashes and power will no longer be delivered. Please charge the portable jump starter with power bank 2 again.

PLEASE NOTE: Recharge the device immediately after use!

PLEASE NOTE: For safety reasons the device cannot be charged if a battery cell is defective or deeply discharged. In this case, please contact our service point.

• Using the jumpstart feature

Step LEDs Meaning	/ Error Solution
1. Connect the jump lead 10 of the power bank 2 to the car jumpstart outlet 9 of the power bank 2	Red Error LED 13 is continuously lit on the jump lead 10.	The voltage determined in the power bank 2 is not enough to start the car.	Charge the power bank 2.
	The green Start LED 12 and the red Error LED 13 flash alternately.	The power bank 2 is ready.	Carry on to step 2...
2. First connect the red clip (A) to the positive pole of the vehicle battery and then connect the black battery clip (B) to the negative pole (see Fig. 1).	The red Error LED 13 lights up continuously, a short alarm signal sounds.	The temperature is too high, possibly due to several jump start attempts.	Disconnect the black battery clip (B) first and then the red battery clip (A) from the battery poles. Start again from step 1.
	The red Error LED 13 lights up continuously, an alarm signal sounds continuously.	Battery clips (A) and (B) are the wrong way round. A short circuit has occurred or the battery is leaking.
	The red Error LED 13 lights up continuously, an alarm signal sounds continuously, followed by two short alarm signals.
	The green Start LED 12 and the red Error LED 13 flash alternately. After 1–2 seconds only the green LED 12 lights up.	The connection is correct.	Carry on with step 3...
3. Starting up the vehicle.

1 B A 2.1. - +

WARNING! As soon as the vehicle starts, remove the jump lead 10 from the portable jump starter with power bank 2 within 30 seconds and disconnect firstly the black battery clip and then the red clip from the battery poles. Otherwise, it could result in dangerous situations! Leave the vehicle engine running.

- Charging mobile phones and tablets

- Press the power switch - Connect your mobile phone or tablet's USB power cable to the USB output (5 V - 1 A USB A 5/2 A USB C 4) and then to your mobile phone or tablet.

PLEASE NOTE: Charging is not possible if the portable jump starter 2 with power bank is being charged itself.

• Using the 12 V DC output 8 A with cigarette lighter adapter

- Press the power switch - Connect the 12 V/8 A cigarette lighter adapter on the 12 V DC output 8 A ^3 to your portable jump starter with power bank ^2 and then connect it to your terminal device.

PLEASE NOTE: You will not be able to use the portable jump starter with power bank 2 if it is being charged.

ATTENTION: Only use the 12 V/8 A cigarette lighter adapter delivered with your product 14 There is a risk of a short circuit if you use third-party adapters.

- Switching the light on

Lighting mode

■ To switch the LED light, press the power switch 8 for the LED light.

■ Press the power switch for the LED light three times to switch the LED light 8a off again.

Flash mode

To switch the LED light on in flash or SOS mode, press the power switch 8 for the LED light. The LED light 8a will then be permanently lit.

- Briefly press the power switch for the LED light once again and the LED light 8a will switch to flash mode.

- Briefly press the power switch for the LED light once again and the LED light 8a will switch to SOS mode. There will be 3 short flashes, 3 long flashes and another 3 short flashes.

- Briefly press the power switch for the LED light once again to switch off the LED light 8a.

ATTENTION: Do not look directly at the LED lights8a as this can damage your eyes.

PLEASE NOTE: It is not possible to turn on the light while the portable jump starter with power bank 2 is being charged.

- FAQs

Q: How can I switch the device off?

A: The device switches off automatically after 20 seconds of non-use. There is no provision for switching it off manually.

Q: How long does it take to fully charge a mobile phone with the device?

A: With a charge level of 3000 mAh: Approx. 3–4 hours if connected to the USB output 5 V ≠ = 1 A USB A 5. Approx. 2–3 hours if connected to the USB output 5 V ≠ = 2 A USB C 4. Please note that if the device is switched on, it will continually use battery power while actually charging and this can extend the charging time.

Q: How long does the device's rechargeable battery pack last?

A: 3–6 months. However, we recommend charging the rechargeable battery pack every 1–2 months.

- Troubleshooting

● = problem
● = cause
= remedy

The portable jump starter with power bank ^2 is not fully charged, even though all 4 indicator lights ^7 are permanently lit.

It is 60% charged after a long period out of use or in storage.

Charge the portable jump starter with power bank ^2 again as described in the section: "Charging the portable jump starter with power bank".

There is no response to pressing the power switch 1.

- The undervoltage protection circuit for the portable jump starter with power bank 2 is activated.

Charge the portable jump starter with power bank ^2 again as described in the section: "Charging the portable jump starter with power bank".

One indicator light 7 flashes, however the portable jump starter with power bank 2 cannot be used.

The undervoltage protection circuit for the portable jump starter with power bank 2 is activated.

Charge the portable jump starter with power bank again as described in the section: "Charging the portable jump starter with power bank".

- Cleaning

WARNING! The device must not come into contact with water or be placed in water. There is a risk of injury due to electric shock if moisture enters the device.

• Do not use cleaners or solvents. These could damage the device beyond repair.
• Keep the housing and device accessories clean.
  ■ Use a damp cloth or a soft brush to clean the device and the

accessories.

- Storage

• Keep the device in a dry location and out of the reach of children.
  ■ Store the device, including accessories, in the storage bkg provided.

• Information about recycling and disposal

DO NOT DISPOSE OF ELECTRICAL TOOLS IN HOUSEHOLD WASTE! DON'T THROW AWAY - RECYCLE!

According to European Directive 2012/19/EU, used electrical devices must be collected separately for environmentally compatible recycling or recovery. The symbol of the crossed out dustbin means that this device must not be disposed of in household waste at the end of its service life. The device must be handed in at established collection points, recycling centres or waste management depots. The disposal of defective devices which you have sent in will be carried out free of charge. In addition, distributors of electrical and electronic equipment as well as food distributors are obliged to accept returned waste. Lidl provides you with return options directly in its branches and shops. Return and disposal is free of charge for you. When buying a new device you have the right to return an equivalent old device at no charge. In addition you have the option, regardless of whether you are buying a new device, to hand in (up to three) old devices at no charge, as long as the device is no larger than 25 cm in any dimension. Before returning the device please delete all personal information. Before returning, please remove batteries or rechargeable battery packs which are not enclosed by the old device, as well as bulbs, which can be removed without destroying the product and take these to a separate collection point.

Instructions for safe removal of batteries or rechargeable battery packs:

WARNING!

The rechargeable battery

pack may only be removed by qualified personnel! RISK OF PERSONAL INJURY THROUGH ELECTRIC SHOCK!

■ Ensure that the battery is completely discharged.
The battery can be removed, once the two halves of the device have been separated from one another. These are held together by commercial screws.
- Carefully remove the battery or the rechargeable battery pack. - The battery or rechargeable battery pack and device can now be disposed of separately.

Batteries containing harmful substances are labelled with the adjacent symbol, which indicates the prohibition on disposal in household waste. The abbreviations for the relevant heavy metals are: Cd = cadmium, Hg = mercury, Pb = lead.

Take used batteries to a waste management company in your city or community or return them to your dealer. This satisfies your legal obligations while also making an important contribution to protecting the environment.

Please note the marking on the different packaging materials and separate them as necessary. The packaging materials are marked with abbreviations (a) and digits (b) with the following definitions: 1–7: Plastics, 20–22: Paper and cardboard, 80–98: Composite materials.

- Original EC Declaration of Conformity

We,

C. M. C. GmbH Holding

Responsible for documentation:

Joachim Bettinger

Katharina-Loth-Str. 15

66386 St. Ingbert

Germany

hereby take sole responsibility for declaring that the product

Portable jump starter with power bank

IAN: 486189_2501

Item no.: 2884

Year of manufacture: 2025/41

Model: UMAP 12000 C4

meets the basic safety requirements as specified in the European Directives

Electromagnetic Compatibility:

(2014/30/EU)

Low Voltage Directive:

(2014/35/EU)

RoHS Directive:

(2011/65/EU), (2015/863/EU)

and the amendments to these Directives.

The object of the declaration described above meets the requirements of Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

This conformity assessment is based on the following harmonised standards:

EN 50498:2010

EN 55032:2015+A11:2020+A1:2020

EN 55035:2017+A11:2020

EN IEC 61000-3-2:2019+A1:2021

EN 61000-3-3:2013+A1:2019+A2:2021

EN 62471:2008

EN IEC 62368-1:2020+A11:2020

EN IEC 62368-3:2020

EN 60335-1:2012+A11:2014+A13:2017+A1:2019+

A14:2019+A2:2019+A15:2021

EN 62233:2008

EN 62841-1:2015+A11:2022

● Warranty and service information

Warranty from C. M. C. GmbH Holding

Dear Customer,

The warranty for this equipment (including the battery) is 3 years from the date of purchase. In the event of product defects, you have legal rights against the retailer of this product. Your statutory rights are not affected in any way by our warranty conditions, which are described below.

- Warranty conditions

The warranty period begins on the date of purchase. Please retain the original sales receipt. This document is required as your proof of purchase.

Should this product show any defect in materials or manufacture within 3 years from the date of purchase, we will repair or replace it – at our discretion – free of charge. This warranty service requires that you retain proof of purchase (sales receipt) for the defective device for the three year period and that you briefly explain in writing what the fault entails and when it occurred. If the defect is covered by our warranty, we will repair and return your product or send you a replacement. The original warranty period is not extended when a device is repair or replaced.

- Warranty period and statutory claims for defects

The warranty period is not extended by the guarantee. This also applies to replaced and repaired parts. Any damages or defects detected at the time of purchase must be reported immediately after unpacking. Any incidental repairs after the warranty period are subject to a fee.

• Extent of warranty

This device has been manufactured according to strict quality guidelines and carefully inspected before delivery.

The warranty applies to material and manufacturing defects only. This warranty does not extend to product parts, which are subject to normal wear and tear and can thus be regarded as consumable parts, or for damages to fragile parts, e.g. switches or parts made from glass.

This warranty is voided if the product becomes damaged or is improperly used or maintained. For proper use of the product, all of the instructions given in the operating instructions must be followed precisely. If the operating instructions advise you or warn you against certain uses or actions, these must be avoided in all circumstances.

The product is for consumer use only and is not intended for commercial or trade use. The warranty becomes void in the event of misuse and improper use, use of force, and any work on the device that has not been carried out by our authorised service branch.

- Processing of warranty claims

To ensure prompt processing of your claim, please follow the instructions given below.

Please retain proof of purchase and the article number (e.g. IAN) for all inquiries.

The product number can be found on the type plate, an engraving, the cover page of your instructions (bottom left), or the sticker on the back or underside of the device.

In the event of malfunctions or other defects, please first contact our service department below by phone or email. If your product is found to be defective, you can then send your product with proof of purchase (till receipt) and a statement describing what the fault involves and when it occurred free of charge to the service address given.

PLEASE NOTE: You can download this handbook and many more, as well as product videos and software at

PDF ONLINE www.lidl-service.com

With this QR code you can gain immediate access to the Lidl Service page (www.lidl-service.com) and you can open your operating instructions by entering the article number (IAN) 486189.

- Service

How to contact us:

GB, IE, NI, CY, MT

Website: www.cmc-creative.de

E-mail: [e-mail]

Phone: [phone]

Registered office: Germany

IAN 486189\_2501

Please note that the following address is not a service address.

Please first contact the service point given above.

Address:

C. M. C. GmbH Holding

Katharina-Loth-Str. 15

66386 St. Ingbert

Germany

Ordering spare parts:

● = Problem
= Ursache
○ = Behebung

[e-mail]

[e-mail]

Telefon: [phone]

EN IEC 62368-1:2020+A11:2020

EN IEC 62368-3:2020

EN 60335-1:2012+A11:2014+A13:2017+A1:2019+

A14:2019+A2:2019+A15:2021

EN 62233:2008

EN 62841-1:2015/A11:2022

EN IEC 62368-1:2020+A11:2020

EN IEC 62368-3:2020

EN 60335-1:2012+A11:2014+A13:2017+A1:2019+

A14:2019+A2:2019+A15:2021

EN 62233:2008

EN 62841-1:2015+A11:2022

St. Ingbert, 1-3-2025

EN IEC 62368-1:2020+A11:2020

EN IEC 62368-3:2020

EN 60335-1:2012+A11:2014+A13:2017+A1:2019+

A14:2019+A2:2019+A15:2021

EN 62233:2008

EN 62841-1:2015+A11:2022

St. Ingbert 1.3.2024

C.M.C. GmbH Holding

$$ C d = k a d m, H g = r t \epsilon c, P b = o \text { of } w. $$

EN IEC 62368-1:2020+A11:2020

EN IEC 62368-3:2020

EN 60335-1:2012+A11:2014+A13:2017+A1:2019+

A14:2019+A2:2019+A15:2021

EN 62233:2008

EN 62841-1:2015+A11:2022

EN IEC 62368-1:2020+A11:2020

EN IEC 62368-3:2020

EN 60335-1:2012+A11:2014+A13:2017+A1:2019+

A14:2019+A2:2019+A15:2021

EN 62233:2008

EN 62841-1:2015+A11:2022

St. Ingbert, 01/03/2025

C.M.C. GmbH Holding

EN IEC 62368-1:2020+A11:2020

EN IEC 62368-3:2020

EN 60335-1:2012+A11:2014+A13:2017+A1:2019+

A14:2019+A2:2019+A15:2021

EN 62233:2008

EN 62841-1:2015+A11:2022

Nome: Riku Service snc

Indirizzo Internet: www.riku-service.com

E-Mail: [e-mail]

Telefono: 0039 (0) 4711430103

Sede: Germania

IAN 486189\_2501

EN IEC 62368-1:2020+A11:2020

EN IEC 62368-3:2020

EN 60335-1:2012+A11:2014+A13:2017+A1:2019+

A14:2019+A2:2019+A15:2021

EN 62233:2008

EN 62841-1:2015+A11:2022