GSA18V-110 Professional - Saw BOSCH - Free user manual and instructions

USER MANUAL GSA18V-110 Professional BOSCH

IMPORTANT Read Before Using

IMPORTANT Lire avant usage

IMPORTANTE Leer antes de usar

Icon of a person reading a book inside a circle (no text or symbols)

Operating / Safety Instructions Consignes d'utilisation / de sécurité Instrucciones de funcionamiento y seguridad

GSA18V-110

BOSCH robotic brush tool with visible mounting bracket and brand logo (no text or symbols on the device itself)

BOSCH

Call Toll Free for Consumer Information & Service Locations Pour obtenir des informations et les adresses de nos centres de service après-vente, appelez ce numéro gratuit Llame gratis para obtener información para el consumidor y ubicaciones de servicio

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

For English Version See page 2

Safety SymbolsThe definitions below describe the level of severity for each signal word.Please read the manual and pay attention to these symbols.
	This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
	DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
	WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
	CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

General Power Tool Safety Warnings

⚠ WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed be-

low may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a Ground Fault Circuit Interrupter (GFCI) protected supply. Use of an GFCI reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and / or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before

making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Battery tool use and care

a. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
b. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
c. When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

General Power Tool Safety Warnings

d. Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
e. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
f. Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 265 °F may cause explosion.

g. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

6. Service

a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
b. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Safety Rules for Cordless Reciprocating Saws

a. Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
b. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.
c. Do not drill, fasten or break into existing walls or other blind areas where electrical wiring may exist. If this situation is unavoidable, disconnect all fuses or circuit breakers feeding this worksite.
d. Keep hands away from cutting area. Do not reach under the material being cut. The proximity of the blade to your hand is hidden from your sight.
e. Keep hands away from the area between the gear housing and saw blade clamp (plunger). The reciprocating blade clamp (blade plunger) can pinch your fingers.
f. Do not use dull or damaged blades. Bent blades can break easily or cause kickback.
g. Before starting to cut, turn tool "ON" and allow the blade to come to full desired speed. Tool can chatter or vibrate if blade

speed is too slow at beginning of cut and possibly kickback.

h. Always wear safety goggles or eye protection when using this tool. Use a dust mask or respirator for applications which generate dust.
i. Secure material before cutting. Never hold it in your hand or across legs. Small or thin material may flex or vibrate with the blade, causing loss of control.
j. Make certain all adjusting screws (knobs) and the blade clamp are tight before making a cut. Loose adjusting screws and clamps can cause the tool or blade to slip and loss of control may result.
k. When removing the blade from the tool avoid contact with skin and use proper protective gloves when grasping the blade or accessory. Accessories may be hot after prolonged use.
1. When using the utility hook always be aware that the blade is exposed. Always hang the tool in area where you or bystanders cannot accidentally make contact with the blade.
m. When operating the saw continuously and for prolonged periods of time, the gearbox may become hot to touch. To reduce the risk of injury, wear protective gloves during saw operation.

Additional Safety Warnings

GFCI and personal protection devices like electrician's rubber gloves and footwear will further enhance your personal safety.

Develop a periodic maintenance schedule for your tool. When cleaning a tool be careful not to disassemble any portion of the tool since internal wires may be misplaced or pinched or safety guard return springs may be improperly mounted. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.

WARNING

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints,
  • Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Symbols

Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.

Symbol Designation/Explanation
V Volts (voltage)
A Amperes (current)
Hz Hertz (frequency, cycles per second)
W Watt (power)
kg Kilograms (weight)
min Minutes (time)
s Seconds (time)
∅	Diameter (size of drill bits, grinding wheels, etc.)
n_0	No load speed (rotational speed, at no load)
n Rated speed (Maximum attainable speed)
.../min	Revolutions or reciprocation per minute (revolutions, strokes, surface speed, orbits etc. per minute)
0 Off position (zero speed, zero torque...)
1, 2, 3, ...I, II, III,	Selector settings (speed, torque or position settings. Higher number means greater speed)
0	Infinitely variable selector with off (speed is increasing from 0 setting)
→	Arrow (action in the direction of arrow)
~	Type or a characteristic of current
==	Type or a characteristic of current
~	Type or a characteristic of current
☐	Designates Double Insulated Construction tools
⊕	Grounding terminal
⚠	Alerts user to warning messages

Symbols

Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.

Symbol Designation/Explanation
	Alerts user to read manual.
	Alerts user to wear eye protection.
	Alerts user to wear respiratory protection.
	Alerts user to wear hearing protection.
	Alerts user to wear eye, respiratory, and hearing protection.
	This symbol designates that this tool is listed by Underwriters Laboratories, to United States and Canadian Standards.
	This symbol designates that this tool is listed by the Canadian Standards Association.
	This symbol designates that this tool is listed by the Canadian Standards Association, to United States and Canadian Standards.
	This symbol designates that this tool is listed by the Intertek Testing Services, to United States and Canadian Standards.
	Designates Li-ion battery recycling program.

Getting to Know Your Product

WARNING

Disconnect battery pack from tool before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce

the risk of starting the tool accidentally.

Bosch GSA18V-110 Cordless Reciprocating Saw

Fig. 1

(1) Saw blade*
(2) Adjustable footplate
(3) Locking sleeve for blade holder
(4) Saw blade receptacle
(5) Hex key
(6) Saw hook
(7) Lock-off button

(8) Variable speed trigger switch
(9) Orbital action on/off lever
(10) Battery pack release button*
(11) Battery pack*
(12) Handle (insulated gripping surface)
(13) Footplate screw
* Sold Separately

Specifications

Model Number GSA18V-110
Voltage rating 18 V
No load speed 0-2,900
Stroke length 1.10” (28mm)
Permitted battery temperature during charging +32...+113°F (0...+45°C)
Permitted ambient temperature during operation and storage -4...+122°F (-20...+50°C)
Recommended ambient temperature during charging +32...+95°F (0...+35°C)

Battery Packs / Chargers:

Please refer to the battery/charger list, included with your tool.

NOTE: For tool specifications refer to the nameplate on your tool.

Intended Use

WARNING

Use this reciprocating saw only as intended. Unintended use may result in personal injury and property damage.

The power tool is suitable for sawing wood, plastic, metal and building materials on a firm surface. It is suitable for straight and curved cuts. When using designated suitable bimetal saw blades, flush cutting is also possible. The saw blade's recommendations are to be observed.

Assembly

WARNING

Disconnect battery pack from tool before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce

the risk of starting the tool accidentally.

Blade Selection

No one blade can be efficient on all cutting jobs. Different materials require specially designed blades. Since your reciprocating saw can cut so many materials, many types of Bosch blades are available. Be sure to use the proper blade to ensure proper cutting performance.

Installing and Removing a Blade

WARNING Make sure that the front end of the blade extends through the footplate for the entire stroke length. Do not use specialty blades that are very short or those with a significant bend. Blade must not contact footplate. A blade which is too short or tilted could jam inside the foot and snap.

Assembly

To install the blade (Fig. 2):

Slide the saw blade (1) into the saw blade holder (4) slot. Make sure the blade is securely locked in place.

If the blade does not snap into place it may be necessary to reset the LockJaw blade holder.

1. Turn the locking sleeve (3) for blade holder (4) approximately 90° in the direction shown, until it locks into the open position and a clicking sound is heard.
2. Then repeat insertion of the blade, checking to make sure it is securely locked in place.

NOTE: Most blades can be installed with teeth pointing either up or down, as desired for the application.

To remove the blade (Fig. 3):

Turn the Locking sleeve (3) for blade holder (4) approximately 90° in the direction shown (Fig. 2). The blade should spring eject how ever due to contaminants it may be necessary to pull the blade (1) out of the blade slot.

NOTE: be careful, blade may be hot.

Inserting and Releasing Battery Pack

WARNING

Ensure the switch is in the off position before in-

serting battery pack. Inserting the battery pack into power tools that have the switch on invites accidents.

Slide charged battery pack (11) into the housing until the battery pack locks into position (Fig. 4).

Your tool is equipped with a secondary locking latch to prevent the battery pack from completely falling out of the tool housing, should it become loose due to vibration.

To remove the battery pack (11), press the battery pack release button (10) and slide the battery pack forward (Fig. 4).

Press the battery pack release button (10) again and slide the battery pack completely out of tool housing (Fig. 4).

Fig. 2 (1) (3) (4)

Fig. 3 (1) (3)

Fig. 4 (10) (11)

Operation

WARNING

Disconnect battery pack from tool before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce

the risk of starting the tool accidentally.

Protection Against Deep Discharging

The lithium ion battery is protected against deep discharging by the "Electronic Cell Protection (ECP)". When the battery is empty, the tool is switched off by means of a protective circuit.

CAUTION

Do not continue to press the trigger switch after the tool has been automatically switched off. The battery can be damaged.

Lock-Off Button

The lock-off button is designed to prevent accidental starts.

To lock the trigger switch (8), press the lock-off button (7) on the side with the lock symbol.

To unlock the trigger switch (8), press the lock-off button (7) on the side with the unlock symbol.

Variable Speed Controlled Trigger Switch

Your tool is equipped with a variable speed controlled trigger switch (8). To turn the tool on, push the lock-off button (7) on the side with the unlock symbol and pull the trigger switch (8) (Fig. 5). The tool will turn itself off as soon as you release the trigger.

The blade stroke rate can be adjusted from the minimum to maximum stroke rate by the pressure you apply to the trigger. Apply more pressure to increase the speed and release pressure to decrease speed.

The required stroke rate is dependent on the material and the working conditions and can be determined by a practical trial.

Reducing the stroke rate is recommended when the saw blade engages in the material as well as when sawing plastic and aluminum.

Fig. 5 (8)(7) ① ② BOSCH

Orbital Action Settings

The orbital action allows for faster and more aggressive cutting by changing the cutting pattern. With orbital action switch (figure 1, 9) you can turn on or off the orbital action.

Orbital action switched off: For cutting thin or hard material such as sheet metal or steel. For achieving clean cutting edges.

Orbital action switched on: For cutting soft materials, e. g., soft building materials, insulation material, softwood. Aggressive rough cutting.

NOTE: For effective cutting in orbital mode blade should be installed with teeth pointing down.

Operation

Saw Hook

WARNING

When using the saw hook always be aware that the

accessory is exposed. Always hang the tool in an area where yourself and bystanders cannot accidentally make contact with the accessory.

WARNING

To reduce the risk of in-jury, use care in selecting ranging the tool.

the location for hanging the tool.

WARNING

Always move lock-off button (7) to the locked ranging tool.

position, before hanging tool.

WARNING

To reduce the risk of in-jury, Do not use the hang-

ing hook if it appears damaged or deformed. This could result in unstable hanging and the tool unexpectedly falling.

Your tool is equipped with a convenient saw hook for hanging your tool. To use, simply lift up hook (6) until it snaps into the open position (Fig. 6).

• Select a suitably sized and shaped object that will provide adequate hanging stability. An unstable hanging surface could result in the tool unexpectedly falling.
• Ensure that the tool is hung out of the way of walkways and working areas with bystanders. The tool could be bumped or a bystander could become entangled causing the tool to unexpectedly fall.

When not in use, always close hook until it snaps into the closed position.

Fig. 6 (6) BOSCH

Operation

Footplate Adjustment

WARNING stalled and secur

Do not operate the saw without footplate in-ed.

WARNING

To reduce the risk of injury, be sure the blade the footplate and all the workpiece throughout the lay shatter if the blade hits its the work at an angle that

The footplate (2) tilts in order to keep as much of its surface in contact with the work surface (Fig. 7).

The footplate (2) can also be locked into any position along 1-1/4" of travel to optimize blade life and/or to reduce blade protrusion beyond the end of the footplate, such as when cutting into large diameter pipe or into walls (Fig. 9).

To adjust the footplate position, loosen the footplate screws (13) with the hex key (5), move the footplate (2) into the desired position, and tighten the footplate screws (13) with the hex key (5). (Fig. 8)

Mechanical tool diagram showing a cutting or turning process with directional arrows and labeled component (2), no readable text or symbols beyond labels.

Fig. 8 (2)(13)(5)

Operation

Using the Saw

WARNING Always hold the saw by the insulated gripping surfaces on the front of the tool and the switch handle. Failure to hold the tool by the insulated gripping surface may result in electric shock or electrocution if sawing into a blind area where live wiring exits.

1. Securely clamp the work.
2. Position to the line of cut and grasp the tool with one hand on the handle and the other placed on the insulated rubber boot over the front housing.
3. Keep the saw footplate firmly against the work to minimize counter-force (jumping) and vibration.
4. Squeeze the trigger to start the tool. Let the saw reach full desired speed before starting the cut. Guide the saw so that the blade will move along the marked line.

Sawing Tips

Following a few simple tips will reduce the wear on the workpiece, the tool and the operator.

1. Blades cut on the draw or back stroke. On fine work, such as paneling, fiberglass, etc., place the good side of workpiece facing down.

2. Use the correct saw blade for the material being cut and keep extra blades on hand to use when others become dull. Replace cracked or bent blades immediately.

3. Select the appropriate cutting speed.

4. To reduce the risk of injury, be sure the blade always extends beyond the foot-plate and work throughout the stroke (Fig. 9). Blades may shatter if the front on the blade hits the work and/or the foot-plate.

Fig. 9 X

1. When cutting metal:

2. Apply a lubricant for easier, smoother, faster cutting and longer blade life.

3. For non-ferrous metals, aluminum, bronze or brass, use a stick wax on the blade.

4. For ferrous metals, iron and steel, use machine or cutting oil along the surface to be cut.
   • See page 11 related to orbital settings when cutting metals.

5. When cutting thin metal, "sandwich" the material between two pieces of scrap wood. Clamp or put in a bench vise. One piece of lumber on top of the metal can be used with adequate clamping. Place your cut lines or design on the wood.

6. Don't force the cutting. Let the saw and blade do the work.

Operation

Pocket/Plunge Cuts

The reciprocating saw can be used to make plunge cuts into softer material, (for example, wood or light building materials for walls), without a starting hole (Fig. 10).

1. Mark the line to be cut clearly on the work.
2. Set the tool with one edge of the footplate (2) firmly against the material.
3. Place the tip of the blade (1) (not running) on the line to be cut.
4. Tilt the saw so that the blade clears the work.
5. Squeeze the trigger switch and carefully engage the moving saw blade into the material.
6. After the blade penetrates through the work, continue sawing along the marked outline.

Notes:

To make plunge cutting easier, use a heavy gauge blade, install the blade with the teeth facing upward, and hold the saw upside down (as shown in Fig. 11).

Do not plunge cut in metal surfaces.

In thick materials and in harder materials, such as metal, plunge cutting should not be attempted. Such materials can be cut with the reciprocating saw only by starting the cut from the edge of the material or from a hole drilled all the way through the material that is large enough to fit the saw blade.

(1) (2) Fig. 10

(1) (2) Fig. 11

Maintenance

WARNING

To avoid accidents, always disconnect the battery pack from tool before servicing or cleaning.

Service

WARNING

NO USER SERVICEABLE PARTS INSIDE. Preventive maintenance performed by un authorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station.

Batteries

Be alert for battery packs that are nearing their end of life. If you notice decreased tool performance or significantly shorter running time between charges then it is time to replace the battery pack. Failure to do so can cause the tool to operate improperly or damage the charger.

Tool Lubrication

Your Bosch tool has been properly lubricated and is ready for use.

Motors

The motor in your tool has been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend it be examined every six months.

Only a genuine Bosch replacement motor specially designed for your tool should be used.

Cleaning

CAUTION

Certain cleaning agents and solvents damage

plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through opening.

Accessory Storage & Maintenance

Store accessories in a cool dry place and avoid freezing. Before use check accessory for cracks and fractures, do not use if damage is suspected.

LockJaw™ Blade Holder Maintenance

Periodically lubricate LockJaw™ blade holder with a dry lubricant such as graphite.

Accessories

WARNING

Do not use attachments/accessories other than those specified by Bosch.

⚠️WARNING Use of attachments/accessories not specified for use with the tool described in this manual may result in damage to tool, property damage, and or personal injury.

Mechanical tool diagram showing a cutting or turning process with directional arrows and labeled component (2), no readable text or symbols beyond labels.

Fig. 8 (2)(13)(5)

Opération

Mechanical tool diagram showing a cutting or turning process with directional arrows and labeled component (2), no readable text or symbols beyond labels.

Fig. 8 (2)(13)(5)

Copyright © 2009-2020 ARM LIMITED

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of ARM nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Copyright (C) 2009 - 2020 ARM LIMITED

© Robert Bosch Tool Corporation 1800 W. Central Road Mt. Prospect, IL 60056-2230

Exportado por: Robert Bosch Tool Corporation Mt. Prospect, IL 60056-2230, E.U.A.